>-----Original Message-----
>From: Phillips Kim-R1AAHA
>Sent: Thursday, October 29, 2009 1:36 AM
>To: Kumar Gopalpet-B05799
>Cc: u-boot@lists.denx.de
>Subject: Re: [PATCH v3 1/2] NET: Move MDIO regs out of TSEC Space
>
>On Wed, 28 Oct 2009 14:19:18 +0530
>Sandeep Gopalpet <sandeep.ku...@freescale.com> wrote:
>
>> Moved the mdio regs out of the tsec structure,and provided different
>> offsets for tsec base and mdio base so that provision for
>etsec2.0 can
>> be provided.
>>
>> This patch helps in providing the support for etsec2.0 In etsec2.0,
>> the MDIO register space and the etsec reg space are different.
>>
>> Also, moved the TSEC_BASE_ADDR and MDIO_BASE_ADDR definitons into
>> platform specific files.
>>
>> Signed-off-by: Sandeep Gopalpet <sandeep.ku...@freescale.com>
>> ---
>
>without this patchseries:
>
>U-Boot 2009.11-rc1 (Oct 28 2009 - 14:57:54) MPC83XX
>
>Reset Status: Software Hard, External/Internal Soft,
>External/Internal Hard
>
>CPU: e300c3, MPC8315E, Rev: 1.0 at 400 MHz, CSB: 133.333 MHz
>Board: Freescale MPC8315ERDB Rev 0.1
>I2C: ready
>DRAM: 128 MB
>FLASH: 8 MB
>NAND: 32 MiB
>PCIE0: No link
>PCIE1: No link
>In: serial
>Out: serial
>Err: serial
>Net: eTSEC0, eTSEC1
>Hit any key to stop autoboot: 0
>=> ping $serverip
>Speed: 1000, full duplex
>Using eTSEC0 device
>host 192.168.1.1 is alive
>=>
>
>with this patchseries:
>
>U-Boot 2009.11-rc1-00002-g3775d27 (Oct 28 2009 - 14:45:51) MPC83XX
>
>Reset Status: Software Hard, External/Internal Soft,
>External/Internal Hard
>
>CPU: e300c3, MPC8315E, Rev: 1.0 at 400 MHz, CSB: 133.333 MHz
>Board: Freescale MPC8315ERDB Rev 0.1
>I2C: ready
>DRAM: 128 MB
>FLASH: 8 MB
>NAND: 32 MiB
>PCIE0: No link
>PCIE1: No link
>In: serial
>Out: serial
>Err: serial
>Net: eTSEC0: No support for PHY id 0; assuming generic
>eTSEC1: No support for PHY id 0; assuming generic eTSEC0,
>eTSEC1 Hit any key to stop autoboot: 0 => ping $serverip
>eTSEC0: No link.
>eTSEC1: No link.
>ping failed; host 192.168.1.1 is not alive
>
>do you not test older version tsecs/83xx?
>
>> +typedef struct tsec_mdio
>> +{
>
>please also move this brace onto the above line.
My bad. I forgot to change the MDIO_OFFSET in the last version of my
patches.
This is the reason why it failed for 83xx series.
Will resend the patches.
Thanks a lot Kim.
-Thanks
Sandeep
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
