Since the introduction of the pinctrl and clk driver and
the dts file, remove unneeded hard coded related code from
the board file.
Signed-off-by: Wenyou Yang <wenyou.y...@atmel.com>
---
Changes in v2: None
board/atmel/sama5d3xek/sama5d3xek.c | 73 +------------------------------------
1 file changed, 1 insertion(+), 72 deletions(-)
diff --git a/board/atmel/sama5d3xek/sama5d3xek.c
b/board/atmel/sama5d3xek/sama5d3xek.c
index 08f1be4fc1..a3486437bd 100644
--- a/board/atmel/sama5d3xek/sama5d3xek.c
+++ b/board/atmel/sama5d3xek/sama5d3xek.c
@@ -16,7 +16,6 @@
#include <lcd.h>
#include <linux/ctype.h>
#include <atmel_hlcdc.h>
-#include <atmel_mci.h>
#include <phy.h>
#include <micrel.h>
#include <net.h>
@@ -135,8 +134,6 @@ static void sama5d3xek_usb_hw_init(void)
#ifdef CONFIG_GENERIC_ATMEL_MCI
static void sama5d3xek_mci_hw_init(void)
{
- at91_mci_hw_init();
-
at91_set_pio_output(AT91_PIO_PORTB, 10, 0); /* MCI0 Power */
}
#endif
@@ -217,12 +214,6 @@ void lcd_show_board_info(void)
int board_early_init_f(void)
{
- at91_periph_clk_enable(ATMEL_ID_PIOA);
- at91_periph_clk_enable(ATMEL_ID_PIOB);
- at91_periph_clk_enable(ATMEL_ID_PIOC);
- at91_periph_clk_enable(ATMEL_ID_PIOD);
- at91_periph_clk_enable(ATMEL_ID_PIOE);
-
at91_seriald_hw_init();
return 0;
@@ -248,9 +239,6 @@ int board_init(void)
#ifdef CONFIG_GENERIC_ATMEL_MCI
sama5d3xek_mci_hw_init();
#endif
-#ifdef CONFIG_ATMEL_SPI
- at91_spi0_hw_init(1 << 0);
-#endif
#ifdef CONFIG_MACB
if (has_emac())
at91_macb_hw_init();
@@ -316,61 +304,6 @@ int board_eth_init(bd_t *bis)
return rc;
}
-#ifdef CONFIG_GENERIC_ATMEL_MCI
-int board_mmc_init(bd_t *bis)
-{
- int rc = 0;
-
- rc = atmel_mci_init((void *)ATMEL_BASE_MCI0);
-
- return rc;
-}
-#endif
-
-/* SPI chip select control */
-#ifdef CONFIG_ATMEL_SPI
-#include <spi.h>
-
-#ifndef CONFIG_DM_SPI
-int spi_cs_is_valid(unsigned int bus, unsigned int cs)
-{
- return bus == 0 && cs < 4;
-}
-
-void spi_cs_activate(struct spi_slave *slave)
-{
- switch (slave->cs) {
- case 0:
- at91_set_pio_output(AT91_PIO_PORTD, 13, 0);
- case 1:
- at91_set_pio_output(AT91_PIO_PORTD, 14, 0);
- case 2:
- at91_set_pio_output(AT91_PIO_PORTD, 15, 0);
- case 3:
- at91_set_pio_output(AT91_PIO_PORTD, 16, 0);
- default:
- break;
- }
-}
-
-void spi_cs_deactivate(struct spi_slave *slave)
-{
- switch (slave->cs) {
- case 0:
- at91_set_pio_output(AT91_PIO_PORTD, 13, 1);
- case 1:
- at91_set_pio_output(AT91_PIO_PORTD, 14, 1);
- case 2:
- at91_set_pio_output(AT91_PIO_PORTD, 15, 1);
- case 3:
- at91_set_pio_output(AT91_PIO_PORTD, 16, 1);
- default:
- break;
- }
-}
-#endif
-#endif /* CONFIG_ATMEL_SPI */
-
#ifdef CONFIG_BOARD_LATE_INIT
int board_late_init(void)
{
@@ -394,12 +327,8 @@ int board_late_init(void)
#ifdef CONFIG_SPL_BUILD
void spl_board_init(void)
{
-#ifdef CONFIG_SYS_USE_MMC
- sama5d3xek_mci_hw_init();
-#elif CONFIG_SYS_USE_NANDFLASH
+#if CONFIG_SYS_USE_NANDFLASH
sama5d3xek_nand_hw_init();
-#elif CONFIG_SYS_USE_SERIALFLASH
- at91_spi0_hw_init(1 << 0);
#endif
}
--
2.11.0
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
