Hi Stephen,
On 29 July 2016 at 13:15, Stephen Warren <swar...@wwwdotorg.org> wrote:
> From: Stephen Warren <swar...@nvidia.com>
>
> p2771-0000 has a couple of PCIe ports; one physically x4 desktop PCI
> connector (which may run at x2 electrically, depending on the board
> version and configuration) and a x1 connection to the M.2 slot (which may
> not be active, depending on the board version and configuration). This
> change enables those.
>
> Signed-off-by: Stephen Warren <swar...@nvidia.com>
> ---
> arch/arm/dts/tegra186-p2771-0000-a02.dts | 19 +++++++++++++++++++
> arch/arm/dts/tegra186-p2771-0000-b00.dts | 19 +++++++++++++++++++
> board/nvidia/p2771-0000/p2771-0000.c | 22 ++++++++++++++++++++++
> configs/p2771-0000-a02_defconfig | 5 +++++
> configs/p2771-0000-b00_defconfig | 5 +++++
> include/configs/p2771-0000.h | 5 +++++
> 6 files changed, 75 insertions(+)
>
> diff --git a/arch/arm/dts/tegra186-p2771-0000-a02.dts
> b/arch/arm/dts/tegra186-p2771-0000-a02.dts
> index 5ed3817a41c6..36a3c21a55de 100644
> --- a/arch/arm/dts/tegra186-p2771-0000-a02.dts
> +++ b/arch/arm/dts/tegra186-p2771-0000-a02.dts
> @@ -10,4 +10,23 @@
> cd-gpios = <&gpio_main TEGRA_MAIN_GPIO(P, 6) GPIO_ACTIVE_LOW>;
> power-gpios = <&gpio_main TEGRA_MAIN_GPIO(P, 5)
> GPIO_ACTIVE_HIGH>;
> };
> +
> + pcie-controller@10003000 {
> + status = "okay";
> +
> + pci@1,0 {
> + status = "okay";
> + nvidia,num-lanes = <2>;
> + };
> +
> + pci@2,0 {
> + status = "disabled";
> + nvidia,num-lanes = <1>;
> + };
> +
> + pci@3,0 {
> + status = "okay";
> + nvidia,num-lanes = <1>;
> + };
> + };
> };
> diff --git a/arch/arm/dts/tegra186-p2771-0000-b00.dts
> b/arch/arm/dts/tegra186-p2771-0000-b00.dts
> index 90c99c33ccc6..0f1d0e83e80d 100644
> --- a/arch/arm/dts/tegra186-p2771-0000-b00.dts
> +++ b/arch/arm/dts/tegra186-p2771-0000-b00.dts
> @@ -10,4 +10,23 @@
> cd-gpios = <&gpio_main TEGRA_MAIN_GPIO(P, 5) GPIO_ACTIVE_LOW>;
> power-gpios = <&gpio_main TEGRA_MAIN_GPIO(P, 6)
> GPIO_ACTIVE_HIGH>;
> };
> +
> + pcie-controller@10003000 {
> + status = "okay";
> +
> + pci@1,0 {
> + status = "okay";
> + nvidia,num-lanes = <4>;
> + };
> +
> + pci@2,0 {
> + status = "disabled";
> + nvidia,num-lanes = <0>;
> + };
> +
> + pci@3,0 {
> + status = "disabled";
> + nvidia,num-lanes = <1>;
> + };
> + };
> };
> diff --git a/board/nvidia/p2771-0000/p2771-0000.c
> b/board/nvidia/p2771-0000/p2771-0000.c
> index 0c828a200542..529ed9d4547a 100644
> --- a/board/nvidia/p2771-0000/p2771-0000.c
> +++ b/board/nvidia/p2771-0000/p2771-0000.c
> @@ -31,3 +31,25 @@ int tegra_board_init(void)
>
> return 0;
> }
> +
> +int tegra_pcie_board_init(void)
> +{
> + struct udevice *dev;
> + uchar val;
> + int ret;
> +
> + /* Turn on MAX77620 LDO7 to 1.05V for PEX power */
> + debug("%s: Set LDO7 for PEX power to 1.05V\n", __func__);
> + ret = i2c_get_chip_for_busnum(0, MAX77620_I2C_ADDR_7BIT, 1, &dev);
> + if (ret) {
> + printf("%s: Cannot find MAX77620 I2C chip\n", __func__);
> + return -1;
> + }
> + /* 0xC5 for 1.05v, enabled: bit7:6 = 11 = enable, bit5:0 = voltage */
> + val = 0xC5;
> + ret = dm_i2c_write(dev, MAX77620_CNFG1_L7_REG, &val, 1);
> + if (ret)
> + printf("i2c_write 0 0x3c 0x31 failed: %d\n", ret);
This looks like it should be a pmic regulator driver.
> +
> + return 0;
> +}
> diff --git a/configs/p2771-0000-a02_defconfig
> b/configs/p2771-0000-a02_defconfig
> index 404f7acf7ef5..5ce369c6d330 100644
> --- a/configs/p2771-0000-a02_defconfig
> +++ b/configs/p2771-0000-a02_defconfig
> @@ -26,7 +26,12 @@ CONFIG_CMD_EXT4=y
> CONFIG_CMD_EXT4_WRITE=y
> CONFIG_CMD_FAT=y
> CONFIG_CMD_FS_GENERIC=y
> +CONFIG_RTL8169=y
> +CONFIG_E1000=y
> +CONFIG_PCI_TEGRA=y
> CONFIG_TEGRA186_BPMP_I2C=y
> CONFIG_SYS_NS16550=y
> CONFIG_USB=y
> CONFIG_DM_USB=y
> +CONFIG_POWER_DOMAIN=y
> +CONFIG_TEGRA186_POWER_DOMAIN=y
> diff --git a/configs/p2771-0000-b00_defconfig
> b/configs/p2771-0000-b00_defconfig
> index ad35c99bbbcc..27393f3a5d46 100644
> --- a/configs/p2771-0000-b00_defconfig
> +++ b/configs/p2771-0000-b00_defconfig
> @@ -26,7 +26,12 @@ CONFIG_CMD_EXT4=y
> CONFIG_CMD_EXT4_WRITE=y
> CONFIG_CMD_FAT=y
> CONFIG_CMD_FS_GENERIC=y
> +CONFIG_RTL8169=y
> +CONFIG_E1000=y
> +CONFIG_PCI_TEGRA=y
> CONFIG_TEGRA186_BPMP_I2C=y
> CONFIG_SYS_NS16550=y
> CONFIG_USB=y
> CONFIG_DM_USB=y
> +CONFIG_POWER_DOMAIN=y
> +CONFIG_TEGRA186_POWER_DOMAIN=y
> diff --git a/include/configs/p2771-0000.h b/include/configs/p2771-0000.h
> index 3ce72086ce9c..1f64405f119a 100644
> --- a/include/configs/p2771-0000.h
> +++ b/include/configs/p2771-0000.h
> @@ -28,6 +28,11 @@
> #define CONFIG_SYS_MMC_ENV_PART 2
> #define CONFIG_ENV_OFFSET (-CONFIG_ENV_SIZE)
>
> +/* PCI host support */
> +#define CONFIG_PCI
> +#define CONFIG_PCI_PNP
> +#define CONFIG_CMD_PCI
> +
> #include "tegra-common-post.h"
>
> /* Crystal is 38.4MHz. clk_m runs at half that rate */
> --
> 2.9.2
>
Regards,
Simon
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
