Add USB host support.

Tested by connecting a USB pen drive:

=> usb start                                                                    
starting USB...                                                                 
USB0:   Port not available.                                                     
USB1:   USB EHCI 1.00                                                           
scanning bus 1 for devices... 2 USB Device(s) found                             
       scanning usb for storage devices... 1 Storage Device(s) found

Signed-off-by: Vanessa Maegima <vanessa.maeg...@nxp.com>
---
 board/technexion/pico-imx6ul/pico-imx6ul.c | 24 +++++++++++++++++++++++-
 include/configs/pico-imx6ul.h              |  2 +-
 2 files changed, 24 insertions(+), 2 deletions(-)

diff --git a/board/technexion/pico-imx6ul/pico-imx6ul.c 
b/board/technexion/pico-imx6ul/pico-imx6ul.c
index c038d43..bdf32f4 100644
--- a/board/technexion/pico-imx6ul/pico-imx6ul.c
+++ b/board/technexion/pico-imx6ul/pico-imx6ul.c
@@ -59,6 +59,9 @@ static iomux_v3_cfg_t const usdhc1_pads[] = {
        MX6_PAD_NAND_CLE__USDHC1_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
 };
 
+#define USB_OTHERREGS_OFFSET   0x800
+#define UCTRL_PWR_POL          (1 << 9)
+
 static iomux_v3_cfg_t const usb_otg_pad[] = {
        MX6_PAD_GPIO1_IO00__ANATOP_OTG1_ID | MUX_PAD_CTRL(OTG_ID_PAD_CTRL),
 };
@@ -98,7 +101,26 @@ int board_early_init_f(void)
 
 int board_usb_phy_mode(int port)
 {
-       return USB_INIT_DEVICE;
+       if (port == 1)
+               return USB_INIT_HOST;
+       else
+               return USB_INIT_DEVICE;
+}
+
+int board_ehci_hcd_init(int port)
+{
+       u32 *usbnc_usb_ctrl;
+
+       if (port > 1)
+               return -EINVAL;
+
+       usbnc_usb_ctrl = (u32 *)(USB_BASE_ADDR + USB_OTHERREGS_OFFSET +
+                                port * 4);
+
+       /* Set Power polarity */
+       setbits_le32(usbnc_usb_ctrl, UCTRL_PWR_POL);
+
+       return 0;
 }
 
 int board_init(void)
diff --git a/include/configs/pico-imx6ul.h b/include/configs/pico-imx6ul.h
index d848ead..01edc03 100644
--- a/include/configs/pico-imx6ul.h
+++ b/include/configs/pico-imx6ul.h
@@ -42,7 +42,7 @@
 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 #define CONFIG_MXC_USB_PORTSC          (PORT_PTS_UTMI | PORT_PTS_PTW)
 #define CONFIG_MXC_USB_FLAGS           0
-#define CONFIG_USB_MAX_CONTROLLER_COUNT        1 /* Only OTG1 port enabled */
+#define CONFIG_USB_MAX_CONTROLLER_COUNT        2
 
 #define CONFIG_CI_UDC
 #define CONFIG_USBD_HS
-- 
1.9.1

_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot

Reply via email to