On 05/17/2016 09:25 AM, York Sun wrote:
> On 05/05/2016 12:29 PM, York Sun wrote:
>> On 04/06/2016 11:50 PM, Shengzhou Liu wrote:
>>> Optimize DDR timing for good margins to support new Transcend
>>> and Apacer DDR4 UDIMM besides current Micron UDIMM.
>>>
>>> Verified 1333MT/s, 1600MT/s, 1866MT/s, 2133MT/s rate with
>>> following UDIMM on LS2080ARDB.
>>> - Micron UDIMM: MTA18ASF1G72AZ-2G1A1Z
>>> - Apacer UDIMM: 78.C1GM4.AF10B
>>> - Transcend UDIMM: TS1GLH72V1H
>>>
>>> Signed-off-by: Shengzhou Liu <shengzhou....@nxp.com>
>>> ---
>>> v2: verified lower rate, for 1333MT/s no changes are necessary.
>>>
>>> board/freescale/ls2080ardb/ddr.h | 6 +++---
>>> 1 file changed, 3 insertions(+), 3 deletions(-)
>>>
>>> diff --git a/board/freescale/ls2080ardb/ddr.h
>>> b/board/freescale/ls2080ardb/ddr.h
>>> index bda9d4a..b3c6306 100644
>>> --- a/board/freescale/ls2080ardb/ddr.h
>>> +++ b/board/freescale/ls2080ardb/ddr.h
>>> @@ -29,9 +29,9 @@ static const struct board_specific_parameters udimm0[] = {
>>> * ranks| mhz| GB |adjst| start | ctl2 | ctl3
>>> */
>>> {2, 1350, 0, 4, 6, 0x0708090B, 0x0C0D0E09,},
>>> - {2, 1666, 0, 4, 8, 0x08090B0D, 0x0E10100C,},
>>> - {2, 1900, 0, 4, 8, 0x090A0C0E, 0x1012120D,},
>>> - {2, 2300, 0, 4, 9, 0x0A0B0C10, 0x1114140E,},
>>> + {2, 1666, 0, 5, 9, 0x090A0B0E, 0x0F11110C,},
>>> + {2, 1900, 0, 6, 0xA, 0x0B0C0E11, 0x1214140F,},
>>> + {2, 2300, 0, 6, 0xB, 0x0C0D0F12, 0x14161610,},
>>> {}
>>> };
>>>
>>>
>>
>> Shengzhou,
>>
>> I see a problem with this patch on one LS2085ARDB board, at 1866MT/s with
>> MT18ASF1G72AZ-2G1A1. Please try it yourself on ls2085rdb-3 (ATX boardfarm).
>> My
>> order of patches are
>>
>> http://patchwork.ozlabs.org/patch/607290/
>> http://patchwork.ozlabs.org/patch/598135/
>> http://patchwork.ozlabs.org/patch/598136/
>> http://patchwork.ozlabs.org/patch/607274/
>>
>> My test code base is master branch bbca7108db79076d3a9a9c112792d7c4608a665c.
>>
>
> Shengzhou,
>
> I rebased the code and repeated the tests on the same board but seeing no
> issue now.
>
Shengzhou,
I am still seeing it unstable on ls2085rdb-5 (ATX boardfarm) at 1866MT/s. It can
boot if I change clk_adjust to 5. Please work with hardware team to confirm.
York
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
