On 03/29/2016 03:56 AM, George Broz wrote: > On 20 March 2016 at 09:49, Marek Vasut <ma...@denx.de> wrote: >> On 03/18/2016 10:22 PM, George Broz wrote: >>> On 18 March 2016 at 12:32, Marek Vasut <ma...@denx.de> wrote: >>>> On 03/18/2016 07:59 PM, George Broz wrote: >>>>> On 16 March 2016 at 18:35, Marek Vasut <ma...@denx.de> wrote: >>>>>> On 03/16/2016 05:17 PM, George Broz wrote: >>>>>>> On 15 March 2016 at 18:29, George Broz <broz...@gmail.com> wrote: >>>>>>> >>>>>>>> >>>>>>>> Hello again - >>>>>>>> >>>>>>>> So under the assumption my SoCKit h/w was broken, I bought a new board. >>>>>>>> They are back ordered on SoCKit boards, so I got a DE0-Nano-SoC >>>>>>>> instead. >>>>>>>> >>>>>>>> I build the v2016.03 (release) version of u-boot-with-spl.sfp. >>>>>>>> >>>>>>>> I power-up the (brand new) board and get: >>>>>>>> >>>>>>>> U-Boot SPL 2016.03 (Mar 15 2016 - 14:52:42) >>>>>>>> drivers/ddr/altera/sequencer.c: Preparing to start memory calibration >>>>>>>> drivers/ddr/altera/sequencer.c: CALIBRATION FAILED >>>>>>>> drivers/ddr/altera/sequencer.c: Calibration complete >>>>>>>> SDRAM calibration failed. >>>>>>>> ### ERROR ### Please RESET the board ### >>>>>>>> >>>>>>>> U-Boot SPL 2016.03 (Mar 15 2016 - 14:52:42) >>>>>>>> drivers/ddr/altera/sequencer.c: Preparing to start memory calibration >>>>>>>> drivers/ddr/altera/sequencer.c: CALIBRATION FAILED >>>>>>>> drivers/ddr/altera/sequencer.c: Calibration complete >>>>>>>> SDRAM calibration failed. >>>>>>>> ### ERROR ### Please RESET the board ### >>>>>>>> >>>>>>>> U-Boot SPL 2016.03 (Mar 15 2016 - 14:52:42) >>>>>>>> drivers/ddr/altera/sequencer.c: Preparing to start memory calibration >>>>>>>> drivers/ddr/altera/sequencer.c: CALIBRATION PASSED >>>>>>>> drivers/ddr/altera/sequencer.c: Calibration complete >>>>>>>> Trying to boot from MMC >>>>>>>> >>>>>>>> U-Boot 2016.03 (Mar 15 2016 - 14:52:42 -0700) >>>>>>>> >>>>>>>> CPU: Altera SoCFPGA Platform >>>>>>>> FPGA: Altera Cyclone V, SE/A4 or SX/C4, version 0x0 >>>>>>>> BOOT: SD/MMC Internal Transceiver (3.0V) >>>>>>>> Watchdog enabled >>>>>>>> I2C: ready >>>>>>>> DRAM: 1 GiB >>>>>>>> MMC: dwmmc0@ff704000: 0 >>>>>>>> In: serial >>>>>>>> Out: serial >>>>>>>> Err: serial >>>>>>>> Model: Terasic DE0-Nano(Atlas) >>>>>>>> Net: >>>>>>>> Error: ethernet@ff702000 address not set. >>>>>>>> No ethernet found. >>>>>>>> Hit any key to stop autoboot: 0 >>>>>>>> => >>>>>>>> >>>>>>>> And this is a good case... usually it doesn't succeed after the fourth >>>>>>>> try >>>>>>>> and I have to cycle power 4 or 5 times before I get lucky. >>>>>>>> >>>>>>>> If I do get lucky and then try to see a USB storage device, then I get: >>>>>>>> >>>>>>>> => >>>>>>>> => usb start >>>>>>>> starting USB... >>>>>>>> USB0: Core Release: 2.93a >>>>>>>> dwc_otg_core_host_init: Timeout! >>>>>>>> dwc_otg_core_host_init: Timeout! >>>>>>>> dwc_otg_core_host_init: Timeout! >>>>>>>> dwc_otg_core_host_init: Timeout! >>>>>>>> dwc_otg_core_host_init: Timeout! >>>>>>>> dwc_otg_core_host_init: Timeout! >>>>>>>> dwc_otg_core_host_init: Timeout! >>>>>>>> dwc_otg_core_host_init: Timeout! >>>>>>>> dwc_otg_core_host_init: Timeout! >>>>>>>> dwc_otg_core_host_init: Timeout! >>>>>>>> dwc_otg_core_host_init: Timeout! >>>>>>>> dwc_otg_core_host_init: Timeout! >>>>>>>> dwc_otg_core_host_init: Timeout! >>>>>>>> dwc_otg_core_host_init: Timeout! >>>>>>>> dwc_otg_core_host_init: Timeout! >>>>>>>> scanning bus 0 for devices... 1 USB Device(s) found >>>>>>>> => >>>>>>>> >>>>>>>> (Every time) >>>>>>>> >>>>>>>> The version of u-boot SPL that ships with the board: >>>>>>>> U-Boot SPL 2013.01.01 (Dec 29 2014 - 15:29:15) >>>>>>>> >>>>>>>> boots every time and has limited USB capability as >>>>>>>> it can see some USB sticks, but not others. >>>>>>>> >>>>>>>> >>>>>>>> Anyway - brand new board - same old symptoms. >>>>>>>> >>>>>>>> Is it perhaps a toolchain problem?? I'm using: >>>>>>>> >>>>>>>> Thread model: posix >>>>>>>> gcc version 4.9.3 20141031 (prerelease) (Linaro GCC 4.9-2014.11) >>>>>>>> >>>>>>>> COLLECT_GCC=arm-poky-linux-gnueabi-gcc >>>>>>>> COLLECT_LTO_WRAPPER=/opt/poky/1.7.1/sysroots/x86_64-pokysdk-linux/usr/libexec/arm-poky-linux-gnueabi/gcc/arm-poky-linux-gnueabi/4.9.3/lto-wrapper >>>>>>>> < snip > >>>>>>>> >>>>>>>> Any advice greatly appreciated. >>>>>>>> >>>>>>>> >>>>>>>> Regards, >>>>>>>> --George Broz >>>>>>> >>>>>>> Rebuilt using the Altera EDS15.0 toolchain: >>>>>>> >>>>>>> arm-altera-eabi-gcc --version >>>>>>> arm-altera-eabi-gcc (Sourcery CodeBench Lite 2014.11-13) 4.9.1 >>>>>>> Copyright (C) 2014 Free Software Foundation, Inc. >>>>>>> This is free software; see the source for copying conditions. There >>>>>>> is NO >>>>>>> warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR >>>>>>> PURPOSE. >>>>>>> >>>>>>> >>>>>>> Get same result ... mostly failing calibration, non-working USB.... >>>>>>> >>>>>>> U-Boot SPL 2016.03 (Mar 16 2016 - 08:27:20) >>>>>>> drivers/ddr/altera/sequencer.c: Preparing to start memory calibration >>>>>>> drivers/ddr/altera/sequencer.c: CALIBRATION FAILED >>>>>>> drivers/ddr/altera/sequencer.c: Calibration complete >>>>>>> SDRAM calibration failed. >>>>>>> ### ERROR ### Please RESET the board ### >>>>>>> >>>>>>> U-Boot SPL 2016.03 (Mar 16 2016 - 08:27:20) >>>>>>> drivers/ddr/altera/sequencer.c: Preparing to start memory calibration >>>>>>> drivers/ddr/altera/sequencer.c: CALIBRATION FAILED >>>>>>> drivers/ddr/altera/sequencer.c: Calibration complete >>>>>>> SDRAM calibration failed. >>>>>>> ### ERROR ### Please RESET the board ### >>>>>>> >>>>>>> U-Boot SPL 2016.03 (Mar 16 2016 - 08:27:20) >>>>>>> drivers/ddr/altera/sequencer.c: Preparing to start memory calibration >>>>>>> drivers/ddr/altera/sequencer.c: CALIBRATION PASSED >>>>>>> drivers/ddr/altera/sequencer.c: Calibration complete >>>>>>> Trying to boot from MMC >>>>>>> >>>>>>> >>>>>>> U-Boot 2016.03 (Mar 16 2016 - 08:27:20 -0700) >>>>>>> >>>>>>> Does this work for anybody else? >>>>>>> Is it in anyone's experience that these (cheaper) Terasic >>>>>>> eval boards are generally out of spec? >>>>>>> >>>>>>> Is there a way to relax the calibration parameters? the USB parameters? >>>>>>> >>>>>>> Would it help if I posted debug output? >>>>>> >>>>>> Sorry for the late reply, I am horribly overloaded now. I asked someone >>>>>> in #u-boot who has the DE0-NANO-SOC board to test latest u-boot/master >>>>>> on it and it apparently worked for him. I should get some more feedback >>>>>> in the morning [ see http://pastebin.com/CM1QJGnh ] . >>>>>> >>>>>> Still, this is getting real creepy. You are the second person who is >>>>>> complaining about misbehavior of terasic boards with mainline u-boot >>>>>> and whatever I do, I cannot replicate this. >>>>>> >>>>>> I am at least CCing the Altera guys. Sorry I have no better suggestion >>>>>> for you :( >>>>>> >>>>>> Best regards, >>>>>> Marek Vasut >>>>> >>>>> >>>>> Hi Marek, >>>>> >>>>> I've got a third board coming to me in the mail (another >>>>> DE0-NANO-SOC). I'll post >>>>> how that goes.If it fails, maybe I'll send it to you... >>>>> >>>>> I've also sent Terasic an email. >>>>> >>>>> One question - after you (your collegue's) SoCKit (Nano) get past memory >>>>> calibration, does USB work (i.e. does the u-boot USB subsystem recognize >>>>> mass >>>>> storage devices)? >>>>> >>>>> I'm beginning to look for solutions that don't involve rebuilding the >>>>> SPL or using USB. >>>> >>>> Try "dcache off" before "usb reset", I had trouble with usb in recent >>>> versions due to cache problems. If this works, I am happy to give you >>>> a workaround, but I would also love a real solution ... which I do not >>>> have for 3+ months now :'-( >>>> >>>> Best regards, >>>> Marek Vasut >>> >>> Thanks, but nope - same story: >>> => dcache off >>> => dcache >>> Data (writethrough) Cache is OFF >>> => usb reset >>> resetting USB... >>> USB0: Core Release: 0.000 >>> SNPSID invalid (not DWC2 OTG device): 00000000 >>> Port not available. >>> USB1: Core Release: 2.93a >>> dwc_otg_core_host_init: Timeout! >>> dwc_otg_core_host_init: Timeout! >>> dwc_otg_core_host_init: Timeout! >>> dwc_otg_core_host_init: Timeout! ... >>> : >>> : >> >> If we cannot get this sorted out and you'd be willing to ship me one of >> those boards, I'd be super-glad to have one. >> >> In the meantime, can you try the ELDK 5.8 toolchain ? You can fetch it >> from [1], go into 5.8 / targets / armv5te and grab >> eldk-glibc-i686-arm-toolchain.sh . Run the script and it will install >> the toolchain into /opt/eldk/ . Then just source >> /opt/eldk-5.8/arm*/environment* script >> and build u-boot as usual. >> >> [1] >> https://www.amazon.com/clouddrive/share/ZDYTL7dwcLT1lkNoHzM4D7UoTJ4ulmPKFQBSW8IuG0I/folder/qoplba6uRqeeSDyEOnqIow >> >> -- >> Best regards, >> Marek Vasut > > Hello Marek, > > I tried the ELDK 5.8 toolchain. On the de0_nano_soc board that > intermittently fails memory calibration > it makes no difference. > > On the second de0_nano_soc board, the same SPL/image that failed on > the other board works every time > on this board, but USB still does not work (using the ELDK toolchain). > > Let me know if we're to the point where you'd need to have the failing board.
Where are you located, australia ? -- Best regards, Marek Vasut _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot