On 8 February 2016 at 02:27, Mateusz Kulikowski <mateusz.kulikow...@gmail.com> wrote: > This driver supports GPIOs present on PM8916 PMIC. > There are 2 device drivers inside: > - GPIO driver (4 "generic" GPIOs) > - Keypad driver that presents itself as GPIO with 2 inputs (power and reset) > > Signed-off-by: Mateusz Kulikowski <mateusz.kulikow...@gmail.com> > Reviewed-by: Simon Glass <s...@chromium.org> > Tested-by: Simon Glass <s...@chromium.org> > --- > > Changes in v3: None > Changes in v2: > - Add Reviewed-by > > Changes in v1: > - Add binding doc > - Fixed inlcude ordering > - Merged direction_input and direction_output functions > - gpio_get: use switch instead of stacked if > - use pmic_clrsetbits > - add possibility to change prwkey bank name > - Handle invalid bindings > - Sanity HW check (i.e. check type/subtype registers) > > doc/device-tree-bindings/gpio/pm8916_gpio.txt | 48 ++++ > drivers/gpio/Kconfig | 10 + > drivers/gpio/Makefile | 1 + > drivers/gpio/pm8916_gpio.c | 302 ++++++++++++++++++++++++++
4 GPIO's pin design, I think this is also comes under pincontrol. > 4 files changed, 361 insertions(+) > create mode 100644 doc/device-tree-bindings/gpio/pm8916_gpio.txt > create mode 100644 drivers/gpio/pm8916_gpio.c > > diff --git a/doc/device-tree-bindings/gpio/pm8916_gpio.txt > b/doc/device-tree-bindings/gpio/pm8916_gpio.txt > new file mode 100644 > index 0000000..58185b8 > --- /dev/null > +++ b/doc/device-tree-bindings/gpio/pm8916_gpio.txt > @@ -0,0 +1,48 @@ > +Driver for part of pm8916 PMIC - gpio and power/reset keys > + > +This device should be child of SPMI pmic. > + > +1) GPIO driver > + > +Required properties: > +- compatible: "qcom,pm8916-gpio" > +- reg: peripheral ID, size of register block > +- gpio-controller > +- gpio-count: number of GPIOs > +- #gpio-cells: 2 > + > +Optional properties: > +- gpio-bank-name: name of bank (as default "pm8916" is used) > + > +Example: > + > +pmic_gpios: gpios@c000 { > + compatible = "qcom,pm8916-gpio"; > + reg = <0xc000 0x400>; > + gpio-controller; > + gpio-count = <4>; > + #gpio-cells = <2>; > + gpio-bank-name="pmic"; > +}; > + > + > +2) Power/Reset key driver > + > +Required properties: > +- compatible: "qcom,pm8916-pwrkey" > +- reg: peripheral ID, size of register block > +- gpio-controller > +- #gpio-cells: 2 > + > +Optional properties: > +- gpio-bank-name: name of bank (as default "pm8916_key" is used) > + > + > +Example: > + > +pmic_pon: pon@800 { > + compatible = "qcom,pm8916-pwrkey"; > + reg = <0x800 0x96>; > + #gpio-cells = <2>; > + gpio-controller; > +}; > diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig > index a5e8182..bbafc63 100644 > --- a/drivers/gpio/Kconfig > +++ b/drivers/gpio/Kconfig > @@ -60,6 +60,16 @@ config MSM_GPIO > - APQ8016 > - MSM8916 > > +config PM8916_GPIO > + bool "Qualcomm PM8916 PMIC GPIO/keypad driver" > + depends on DM_GPIO && PMIC_PM8916 > + help > + Support for GPIO pins and power/reset buttons found on > + Qualcomm PM8916 PMIC. > + Default name for GPIO bank is "pm8916". > + Power and reset buttons are placed in "pm8916_key" bank and > + have gpio numbers 0 and 1 respectively. > + > config ROCKCHIP_GPIO > bool "Rockchip GPIO driver" > depends on DM_GPIO > diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile > index 6083c4a..8e880bd 100644 > --- a/drivers/gpio/Makefile > +++ b/drivers/gpio/Makefile > @@ -48,3 +48,4 @@ obj-$(CONFIG_VYBRID_GPIO) += vybrid_gpio.o > obj-$(CONFIG_HIKEY_GPIO) += hi6220_gpio.o > obj-$(CONFIG_PIC32_GPIO) += pic32_gpio.o > obj-$(CONFIG_MSM_GPIO) += msm_gpio.o > +obj-$(CONFIG_PM8916_GPIO) += pm8916_gpio.o > diff --git a/drivers/gpio/pm8916_gpio.c b/drivers/gpio/pm8916_gpio.c > new file mode 100644 > index 0000000..1abab7f > --- /dev/null > +++ b/drivers/gpio/pm8916_gpio.c > @@ -0,0 +1,302 @@ > +/* > + * Qualcomm pm8916 pmic gpio driver - part of Qualcomm PM8916 PMIC > + * > + * (C) Copyright 2015 Mateusz Kulikowski <mateusz.kulikow...@gmail.com> > + * > + * SPDX-License-Identifier: GPL-2.0+ > + */ > + > +#include <common.h> > +#include <dm.h> > +#include <power/pmic.h> > +#include <spmi/spmi.h> > +#include <asm/io.h> > +#include <asm/gpio.h> > +#include <linux/bitops.h> > + > +DECLARE_GLOBAL_DATA_PTR; > + > +/* Register offset for each gpio */ > +#define REG_OFFSET(x) ((x) * 0x100) > + > +/* Register maps */ > + > +/* Type and subtype are shared for all pm8916 peripherals */ > +#define REG_TYPE 0x4 > +#define REG_SUBTYPE 0x5 > + > +#define REG_STATUS 0x08 > +#define REG_STATUS_VAL_MASK 0x1 > + > +/* MODE_CTL */ > +#define REG_CTL 0x40 > +#define REG_CTL_MODE_MASK 0x70 > +#define REG_CTL_MODE_INPUT 0x00 > +#define REG_CTL_MODE_INOUT 0x20 > +#define REG_CTL_MODE_OUTPUT 0x10 > +#define REG_CTL_OUTPUT_MASK 0x0F > + > +#define REG_DIG_VIN_CTL 0x41 > +#define REG_DIG_VIN_VIN0 0 > + > +#define REG_DIG_PULL_CTL 0x42 > +#define REG_DIG_PULL_NO_PU 0x5 > + > +#define REG_DIG_OUT_CTL 0x45 > +#define REG_DIG_OUT_CTL_CMOS (0x0 << 4) > +#define REG_DIG_OUT_CTL_DRIVE_L 0x1 > + > +#define REG_EN_CTL 0x46 > +#define REG_EN_CTL_ENABLE (1 << 7) > + > +struct pm8916_gpio_bank { > + uint16_t pid; /* Peripheral ID on SPMI bus */ > +}; > + > +static int pm8916_gpio_set_direction(struct udevice *dev, unsigned offset, > + bool input, int value) > +{ > + struct pm8916_gpio_bank *priv = dev_get_priv(dev); > + uint32_t gpio_base = priv->pid + REG_OFFSET(offset); > + int ret; > + > + /* Disable the GPIO */ > + ret = pmic_clrsetbits(dev->parent, gpio_base + REG_EN_CTL, > + REG_EN_CTL_ENABLE, 0); > + if (ret < 0) > + return ret; > + > + /* Select the mode */ > + if (input) > + ret = pmic_reg_write(dev->parent, gpio_base + REG_CTL, > + REG_CTL_MODE_INPUT); > + else > + ret = pmic_reg_write(dev->parent, gpio_base + REG_CTL, > + REG_CTL_MODE_INOUT | (value ? 1 : 0)); > + if (ret < 0) > + return ret; > + > + /* Set the right pull (no pull) */ > + ret = pmic_reg_write(dev->parent, gpio_base + REG_DIG_PULL_CTL, > + REG_DIG_PULL_NO_PU); > + if (ret < 0) > + return ret; > + > + /* Configure output pin drivers if needed */ > + if (!input) { > + /* Select the VIN - VIN0, pin is input so it doesn't matter */ > + ret = pmic_reg_write(dev->parent, gpio_base + REG_DIG_VIN_CTL, > + REG_DIG_VIN_VIN0); > + if (ret < 0) > + return ret; > + > + /* Set the right dig out control */ > + ret = pmic_reg_write(dev->parent, gpio_base + REG_DIG_OUT_CTL, > + REG_DIG_OUT_CTL_CMOS | > + REG_DIG_OUT_CTL_DRIVE_L); > + if (ret < 0) > + return ret; > + } > + > + /* Enable the GPIO */ > + return pmic_clrsetbits(dev->parent, gpio_base + REG_EN_CTL, 0, > + REG_EN_CTL_ENABLE); > +} > + > +static int pm8916_gpio_direction_input(struct udevice *dev, unsigned offset) > +{ > + return pm8916_gpio_set_direction(dev, offset, true, 0); > +} > + > +static int pm8916_gpio_direction_output(struct udevice *dev, unsigned offset, > + int value) > +{ > + return pm8916_gpio_set_direction(dev, offset, false, value); > +} > + > +static int pm8916_gpio_get_function(struct udevice *dev, unsigned offset) > +{ > + struct pm8916_gpio_bank *priv = dev_get_priv(dev); > + uint32_t gpio_base = priv->pid + REG_OFFSET(offset); > + int reg; > + > + /* Set the output value of the gpio */ > + reg = pmic_reg_read(dev->parent, gpio_base + REG_CTL); > + if (reg < 0) > + return reg; > + > + switch (reg & REG_CTL_MODE_MASK) { > + case REG_CTL_MODE_INPUT: > + return GPIOF_INPUT; > + case REG_CTL_MODE_INOUT: /* Fallthrough */ > + case REG_CTL_MODE_OUTPUT: > + return GPIOF_OUTPUT; > + default: > + return GPIOF_UNKNOWN; > + } > +} > + > +static int pm8916_gpio_get_value(struct udevice *dev, unsigned offset) > +{ > + struct pm8916_gpio_bank *priv = dev_get_priv(dev); > + uint32_t gpio_base = priv->pid + REG_OFFSET(offset); > + int reg; > + > + reg = pmic_reg_read(dev->parent, gpio_base + REG_STATUS); > + if (reg < 0) > + return reg; > + > + return !!(reg & REG_STATUS_VAL_MASK); > +} > + > +static int pm8916_gpio_set_value(struct udevice *dev, unsigned offset, > + int value) > +{ > + struct pm8916_gpio_bank *priv = dev_get_priv(dev); > + uint32_t gpio_base = priv->pid + REG_OFFSET(offset); > + > + /* Set the output value of the gpio */ > + return pmic_clrsetbits(dev->parent, gpio_base + REG_CTL, > + REG_CTL_OUTPUT_MASK, !!value); > +} > + > +static const struct dm_gpio_ops pm8916_gpio_ops = { > + .direction_input = pm8916_gpio_direction_input, > + .direction_output = pm8916_gpio_direction_output, > + .get_value = pm8916_gpio_get_value, > + .set_value = pm8916_gpio_set_value, > + .get_function = pm8916_gpio_get_function, > +}; > + > +static int pm8916_gpio_probe(struct udevice *dev) > +{ > + struct pm8916_gpio_bank *priv = dev_get_priv(dev); > + int reg; > + > + priv->pid = dev_get_addr(dev); > + if (priv->pid == FDT_ADDR_T_NONE) > + return -EINVAL; > + > + /* Do a sanity check */ > + reg = pmic_reg_read(dev->parent, priv->pid + REG_TYPE); > + if (reg != 0x10) > + return -ENODEV; > + > + reg = pmic_reg_read(dev->parent, priv->pid + REG_SUBTYPE); > + if (reg != 0x5) > + return -ENODEV; > + > + return 0; > +} > + > +static int pm8916_gpio_ofdata_to_platdata(struct udevice *dev) > +{ > + struct gpio_dev_priv *uc_priv = dev_get_uclass_priv(dev); > + > + uc_priv->gpio_count = fdtdec_get_int(gd->fdt_blob, dev->of_offset, > + "gpio-count", 0); > + uc_priv->bank_name = fdt_getprop(gd->fdt_blob, dev->of_offset, > + "gpio-bank-name", NULL); > + if (uc_priv->bank_name == NULL) > + uc_priv->bank_name = "pm8916"; > + > + return 0; > +} > + > +static const struct udevice_id pm8916_gpio_ids[] = { > + { .compatible = "qcom,pm8916-gpio" }, > + { } > +}; > + > +U_BOOT_DRIVER(gpio_pm8916) = { > + .name = "gpio_pm8916", > + .id = UCLASS_GPIO, > + .of_match = pm8916_gpio_ids, > + .ofdata_to_platdata = pm8916_gpio_ofdata_to_platdata, > + .probe = pm8916_gpio_probe, > + .ops = &pm8916_gpio_ops, > + .priv_auto_alloc_size = sizeof(struct pm8916_gpio_bank), > +}; > + > + > +/* Add pmic buttons as GPIO as well - there is no generic way for now */ > +#define PON_INT_RT_STS 0x10 > +#define KPDPWR_ON_INT_BIT 0 > +#define RESIN_ON_INT_BIT 1 > + > +static int pm8941_pwrkey_get_function(struct udevice *dev, unsigned offset) > +{ > + return GPIOF_INPUT; > +} > + > +static int pm8941_pwrkey_get_value(struct udevice *dev, unsigned offset) > +{ > + struct pm8916_gpio_bank *priv = dev_get_priv(dev); > + > + int reg = pmic_reg_read(dev->parent, priv->pid + PON_INT_RT_STS); > + > + if (reg < 0) > + return 0; > + > + switch (offset) { > + case 0: /* Power button */ > + return (reg & BIT(KPDPWR_ON_INT_BIT)) != 0; > + break; > + case 1: /* Reset button */ > + default: > + return (reg & BIT(RESIN_ON_INT_BIT)) != 0; > + break; > + } > +} > + > +static const struct dm_gpio_ops pm8941_pwrkey_ops = { > + .get_value = pm8941_pwrkey_get_value, > + .get_function = pm8941_pwrkey_get_function, > +}; > + > +static int pm8941_pwrkey_probe(struct udevice *dev) > +{ > + struct pm8916_gpio_bank *priv = dev_get_priv(dev); > + int reg; > + > + priv->pid = dev_get_addr(dev); > + if (priv->pid == FDT_ADDR_T_NONE) > + return -EINVAL; > + > + /* Do a sanity check */ > + reg = pmic_reg_read(dev->parent, priv->pid + REG_TYPE); > + if (reg != 0x1) > + return -ENODEV; > + > + reg = pmic_reg_read(dev->parent, priv->pid + REG_SUBTYPE); > + if (reg != 0x1) > + return -ENODEV; > + > + return 0; > +} > + > +static int pm8941_pwrkey_ofdata_to_platdata(struct udevice *dev) > +{ > + struct gpio_dev_priv *uc_priv = dev_get_uclass_priv(dev); > + > + uc_priv->gpio_count = 2; > + if (uc_priv->bank_name == NULL) > + uc_priv->bank_name = "pm8916_key"; > + > + return 0; > +} > + > +static const struct udevice_id pm8941_pwrkey_ids[] = { > + { .compatible = "qcom,pm8916-pwrkey" }, > + { } > +}; > + > +U_BOOT_DRIVER(pwrkey_pm8941) = { > + .name = "pwrkey_pm8916", > + .id = UCLASS_GPIO, > + .of_match = pm8941_pwrkey_ids, > + .ofdata_to_platdata = pm8941_pwrkey_ofdata_to_platdata, > + .probe = pm8941_pwrkey_probe, > + .ops = &pm8941_pwrkey_ops, > + .priv_auto_alloc_size = sizeof(struct pm8916_gpio_bank), > +}; > -- > 2.5.0 > > _______________________________________________ > U-Boot mailing list > U-Boot@lists.denx.de > http://lists.denx.de/mailman/listinfo/u-boot -- Jagan. _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot