Hi Anand,
I have a odroid-xu4, but it doesn't detect the rtl8153:
U-Boot 2016.01-rc1-00441-g75507d5-dirty (Dec 07 2015 - 15:46:09 +0800) for
ODROID-XU3
CPU: Exynos5422 @ 800 MHz
Model: Odroid XU3 based on EXYNOS5422
Board: Odroid XU3 based on EXYNOS5422
Type: xu4
DRAM: 2 GiB
__of_translate_address: Bad cell count for gpx0
MMC: EXYNOS DWMMC: 0, EXYNOS DWMMC: 1
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: No ethernet found.
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
starting USB...
USB0: USB EHCI 1.00
USB1: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.00
USB2: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.00
scanning bus 0 for devices... 1 USB Device(s) found
scanning bus 1 for devices... 2 USB Device(s) found
scanning bus 2 for devices... 2 USB Device(s) found
scanning usb for ethernet devices... Setup ERROR: address device
command for slot 1.
Unknown version 0x0000
Unknown Device
0 Ethernet Device(s) found
No ethernet found.
could you send me your odroid-xu3_defconfig? Thanks.
BTW, I added "#define CONFIG_USB_ETHER_RTL8152" to
include/configs/exynos5-common.h
Regards,
Joe
On Wed, Nov 25, 2015 at 5:09 PM, Anand Moon <linux.am...@gmail.com> wrote:
> Hi Ted,
>
> On 25 November 2015 at 11:27, Ted Chen <tedc...@realtek.com> wrote:
> > Add a condition of set_address and set_configuration to check
> > if the request is standardized.
> >
> > Signed-off-by: Ted Chen <tedc...@realtek.com>
> > ---
> > drivers/usb/host/xhci.c | 6 ++++--
> > 1 file changed, 4 insertions(+), 2 deletions(-)
> >
> > diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c
> > index ca598aa..cb8a04b 100644
> > --- a/drivers/usb/host/xhci.c
> > +++ b/drivers/usb/host/xhci.c
> > @@ -941,10 +941,12 @@ static int _xhci_submit_control_msg(struct
> usb_device *udev, unsigned long pipe,
> > if (usb_pipedevice(pipe) == ctrl->rootdev)
> > return xhci_submit_root(udev, pipe, buffer, setup);
> >
> > - if (setup->request == USB_REQ_SET_ADDRESS)
> > + if (setup->request == USB_REQ_SET_ADDRESS &&
> > + (setup->requesttype & USB_TYPE_MASK) == USB_TYPE_STANDARD)
> > return xhci_address_device(udev, root_portnr);
> >
> > - if (setup->request == USB_REQ_SET_CONFIGURATION) {
> > + if (setup->request == USB_REQ_SET_CONFIGURATION &&
> > + (setup->requesttype & USB_TYPE_MASK) == USB_TYPE_STANDARD) {
> > ret = xhci_set_configuration(udev);
> > if (ret) {
> > puts("Failed to configure xHCI endpoint\n");
> > --
> > 1.7.9.5
> >
>
> Tested on Odroid-XU4 with Ethernet USB3.0 RT8153-VB.
>
> Tested-by: Anand Moon <linux.am...@gmail.com>
> Reviewed-by: Anand Moon <linux.am...@gmail.com>
>
> -Anand Moon
> _______________________________________________
> U-Boot mailing list
> U-Boot@lists.denx.de
> http://lists.denx.de/mailman/listinfo/u-boot
>
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
