On 02-09-15, 11:10, Stefan Roese wrote:
> This patch adds support for 4-bit ECC BCH4 for the SPEAr600 SoC. This can
> be used by boards equipped with a NAND chip that requires 4-bit ECC strength.
> The SPEAr600 HW ECC only supports 1-bit ECC strength.
>
> To enable SW BCH4, you need to specify this in your config header:
>
> And use the command "nandecc bch4" to select this ECC scheme upon runtime.
>
> Tested on SPEAr600 x600 board.
>
> Signed-off-by: Stefan Roese <s...@denx.de>
> Cc: Scott Wood <scottw...@freescale.com>
> Cc: Viresh Kumar <viresh.ku...@linaro.org>
> ---
> drivers/mtd/nand/fsmc_nand.c | 40 ++++++++++++++++++++++++++++++++++++++++
> 1 file changed, 40 insertions(+)
>
> diff --git a/drivers/mtd/nand/fsmc_nand.c b/drivers/mtd/nand/fsmc_nand.c
> index 567eff0..19f5526 100644
> --- a/drivers/mtd/nand/fsmc_nand.c
> +++ b/drivers/mtd/nand/fsmc_nand.c
> @@ -13,6 +13,7 @@
> #include <asm/io.h>
> #include <linux/bitops.h>
> #include <linux/err.h>
> +#include <linux/mtd/nand_bch.h>
> #include <linux/mtd/nand_ecc.h>
> #include <linux/mtd/fsmc_nand.h>
> #include <asm/arch/hardware.h>
> @@ -390,6 +391,45 @@ static int fsmc_read_page_hwecc(struct mtd_info *mtd,
> struct nand_chip *chip,
> return 0;
> }
>
> +#ifndef CONFIG_SPL_BUILD
> +/*
> + * fsmc_nand_switch_ecc - switch the ECC operation between different engines
> + *
> + * @eccstrength - the number of bits that could be corrected
> + * (1 - HW, 4 - SW BCH4)
> + */
> +int __maybe_unused fsmc_nand_switch_ecc(uint32_t eccstrength)
> +{
> + struct nand_chip *nand;
> + struct mtd_info *mtd;
> + int err = 0;
You don't have to initialize it.
> +
> + mtd = &nand_info[nand_curr_device];
> + nand = mtd->priv;
> +
> + /* Setup the ecc configurations again */
> + if (eccstrength == 1) {
> + nand->ecc.mode = NAND_ECC_HW;
> + nand->ecc.bytes = 3;
> + nand->ecc.strength = 1;
> + nand->ecc.layout = &fsmc_ecc1_layout;
> + nand->ecc.correct = nand_correct_data;
> + } else {
> + nand->ecc.mode = NAND_ECC_SOFT_BCH;
> + nand->ecc.calculate = nand_bch_calculate_ecc;
> + nand->ecc.correct = nand_bch_correct_data;
> + nand->ecc.bytes = 7;
> + nand->ecc.strength = 4;
> + nand->ecc.layout = NULL;
> + }
> +
> + /* Update NAND handling after ECC mode switch */
> + err = nand_scan_tail(mtd);
> +
> + return err;
> +}
> +#endif /* CONFIG_SPL_BUILD */
> +
> int fsmc_nand_init(struct nand_chip *nand)
> {
> static int chip_nr;
Other than that:
Acked-by: Viresh Kumar <viresh.ku...@linaro.org>
--
viresh
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
