This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masah...@socionext.com>
---
arch/powerpc/cpu/mpc5xxx/Kconfig | 4 -
board/v38b/Kconfig | 9 --
board/v38b/MAINTAINERS | 6 -
board/v38b/Makefile | 8 -
board/v38b/ethaddr.c | 197 -----------------------
board/v38b/v38b.c | 260 ------------------------------
configs/v38b_defconfig | 4 -
include/configs/v38b.h | 333 ---------------------------------------
8 files changed, 821 deletions(-)
delete mode 100644 board/v38b/Kconfig
delete mode 100644 board/v38b/MAINTAINERS
delete mode 100644 board/v38b/Makefile
delete mode 100644 board/v38b/ethaddr.c
delete mode 100644 board/v38b/v38b.c
delete mode 100644 configs/v38b_defconfig
delete mode 100644 include/configs/v38b.h
diff --git a/arch/powerpc/cpu/mpc5xxx/Kconfig b/arch/powerpc/cpu/mpc5xxx/Kconfig
index dc86ac3..7fa948f 100644
--- a/arch/powerpc/cpu/mpc5xxx/Kconfig
+++ b/arch/powerpc/cpu/mpc5xxx/Kconfig
@@ -18,9 +18,6 @@ config TARGET_A4M072
config TARGET_CM5200
bool "Support cm5200"
-config TARGET_V38B
- bool "Support v38b"
-
config TARGET_O2D
bool "Support O2D"
@@ -56,6 +53,5 @@ source "board/cm5200/Kconfig"
source "board/ifm/o2dnt2/Kconfig"
source "board/intercontrol/digsy_mtc/Kconfig"
source "board/tqc/tqm5200/Kconfig"
-source "board/v38b/Kconfig"
endmenu
diff --git a/board/v38b/Kconfig b/board/v38b/Kconfig
deleted file mode 100644
index 653bfc1..0000000
--- a/board/v38b/Kconfig
+++ /dev/null
@@ -1,9 +0,0 @@
-if TARGET_V38B
-
-config SYS_BOARD
- default "v38b"
-
-config SYS_CONFIG_NAME
- default "v38b"
-
-endif
diff --git a/board/v38b/MAINTAINERS b/board/v38b/MAINTAINERS
deleted file mode 100644
index d1a6ae6..0000000
--- a/board/v38b/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-V38B BOARD
-#M: -
-S: Maintained
-F: board/v38b/
-F: include/configs/v38b.h
-F: configs/v38b_defconfig
diff --git a/board/v38b/Makefile b/board/v38b/Makefile
deleted file mode 100644
index a20a5ef..0000000
--- a/board/v38b/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# (C) Copyright 2003-2006
-# Wolfgang Denk, DENX Software Engineering, w...@denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y := v38b.o ethaddr.o
diff --git a/board/v38b/ethaddr.c b/board/v38b/ethaddr.c
deleted file mode 100644
index 982998f..0000000
--- a/board/v38b/ethaddr.c
+++ /dev/null
@@ -1,197 +0,0 @@
-/*
- * (C) Copyright 2006
- * Wolfgang Denk, DENX Software Engineering, w...@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <mpc5xxx.h>
-
-/* For the V38B board the pin is GPIO_PSC_6 */
-#define GPIO_PIN GPIO_PSC6_0
-
-#define NO_ERROR 0
-#define ERR_NO_NUMBER 1
-#define ERR_BAD_NUMBER 2
-
-static int is_high(void);
-static int check_device(void);
-static void io_out(int value);
-static void io_input(void);
-static void io_output(void);
-static void init_gpio(void);
-static void read_byte(unsigned char *data);
-static void write_byte(unsigned char command);
-
-void read_2501_memory(unsigned char *psernum, unsigned char *perr);
-void board_get_enetaddr(uchar *enetaddr);
-
-
-static int is_high()
-{
- return (*((vu_long *) MPC5XXX_WU_GPIO_DATA_I) & GPIO_PIN);
-}
-
-static void io_out(int value)
-{
- if (value)
- *((vu_long *) MPC5XXX_WU_GPIO_DATA_O) |= GPIO_PIN;
- else
- *((vu_long *) MPC5XXX_WU_GPIO_DATA_O) &= ~GPIO_PIN;
-}
-
-static void io_input()
-{
- *((vu_long *) MPC5XXX_WU_GPIO_DIR) &= ~GPIO_PIN;
- udelay(3); /* allow input to settle */
-}
-
-static void io_output()
-{
- *((vu_long *) MPC5XXX_WU_GPIO_DIR) |= GPIO_PIN;
-}
-
-static void init_gpio()
-{
- *((vu_long *) MPC5XXX_WU_GPIO_ENABLE) |= GPIO_PIN; /* Enable
appropriate pin */
-}
-
-void read_2501_memory(unsigned char *psernum, unsigned char *perr)
-{
-#define NBYTES 28
- unsigned char crcval, i;
- unsigned char buf[NBYTES];
-
- *perr = 0;
- crcval = 0;
-
- for (i = 0; i < NBYTES; i++)
- buf[i] = 0;
-
- if (!check_device())
- *perr = ERR_NO_NUMBER;
- else {
- *perr = NO_ERROR;
- write_byte(0xCC); /* skip ROM (0xCC) */
- write_byte(0xF0); /* Read memory command 0xF0 */
- write_byte(0x00); /* Address TA1=0, TA2=0 */
- write_byte(0x00);
- read_byte(&crcval); /* Read CRC of address and
command */
-
- for (i = 0; i < NBYTES; i++)
- read_byte(&buf[i]);
- }
- if (strncmp((const char *) &buf[11], "MAREL IEEE 802.3", 16)) {
- *perr = ERR_BAD_NUMBER;
- psernum[0] = 0x00;
- psernum[1] = 0xE0;
- psernum[2] = 0xEE;
- psernum[3] = 0xFF;
- psernum[4] = 0xFF;
- psernum[5] = 0xFF;
- } else {
- psernum[0] = 0x00;
- psernum[1] = 0xE0;
- psernum[2] = 0xEE;
- psernum[3] = buf[7];
- psernum[4] = buf[6];
- psernum[5] = buf[5];
- }
-}
-
-static int check_device()
-{
- int found;
-
- io_output();
- io_out(0);
- udelay(500); /* must be at least 480 us low pulse */
-
- io_input();
- udelay(60);
-
- found = (is_high() == 0) ? 1 : 0;
- udelay(500); /* must be at least 480 us low pulse */
-
- return found;
-}
-
-static void write_byte(unsigned char command)
-{
- char i;
-
- for (i = 0; i < 8; i++) {
- /* 1 us to 15 us low pulse starts bit slot */
- /* Start with high pulse for 3 us */
- io_input();
- udelay(3);
-
- io_out(0);
- io_output();
- udelay(3);
-
- if (command & 0x01) {
- /* 60 us high for 1-bit */
- io_input();
- udelay(60);
- } else
- /* 60 us low for 0-bit */
- udelay(60);
- /* Leave pin as input */
- io_input();
-
- command = command >> 1;
- }
-}
-
-static void read_byte(unsigned char *data)
-{
- unsigned char i, rdat = 0;
-
- for (i = 0; i < 8; i++) {
- /* read one bit from one-wire device */
-
- /* 1 - 15 us low starts bit slot */
- io_out(0);
- io_output();
- udelay(0);
-
- /* allow line to be pulled high */
- io_input();
-
- /* delay 10 us */
- udelay(10);
-
- /* now sample input status */
- if (is_high())
- rdat = (rdat >> 1) | 0x80;
- else
- rdat = rdat >> 1;
-
- udelay(60); /* at least 60 us */
- }
- /* copy the return value */
- *data = rdat;
-}
-
-void board_get_enetaddr(uchar *enetaddr)
-{
- unsigned char sn[6], err = NO_ERROR;
-
- init_gpio();
-
- read_2501_memory(sn, &err);
-
- if (err == NO_ERROR) {
- sprintf((char *)enetaddr, "%02x:%02x:%02x:%02x:%02x:%02x",
- sn[0], sn[1], sn[2], sn[3], sn[4], sn[5]);
- printf("MAC address: %s\n", enetaddr);
- setenv("ethaddr", (char *)enetaddr);
- } else {
- sprintf((char *)enetaddr, "00:01:02:03:04:05");
- printf("Error reading MAC address.\n");
- printf("Setting default to %s\n", enetaddr);
- setenv("ethaddr", (char *)enetaddr);
- }
-}
diff --git a/board/v38b/v38b.c b/board/v38b/v38b.c
deleted file mode 100644
index a337729..0000000
--- a/board/v38b/v38b.c
+++ /dev/null
@@ -1,260 +0,0 @@
-/*
- * (C) Copyright 2003-2006
- * Wolfgang Denk, DENX Software Engineering, w...@denx.de.
- *
- * (C) Copyright 2004
- * Mark Jonas, Freescale Semiconductor, mark.jo...@motorola.com.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <mpc5xxx.h>
-#include <net.h>
-#include <asm/processor.h>
-
-
-#ifndef CONFIG_SYS_RAMBOOT
-static void sdram_start(int hi_addr)
-{
- long hi_addr_bit = hi_addr ? 0x01000000 : 0;
-
- /* unlock mode register */
- *(vu_long *) MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000000 |
hi_addr_bit;
- __asm__ volatile ("sync");
-
- /* precharge all banks */
- *(vu_long *) MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000002 |
hi_addr_bit;
- __asm__ volatile ("sync");
-
-#if SDRAM_DDR
- /* set mode register: extended mode */
- *(vu_long *) MPC5XXX_SDRAM_MODE = SDRAM_EMODE;
- __asm__ volatile ("sync");
-
- /* set mode register: reset DLL */
- *(vu_long *) MPC5XXX_SDRAM_MODE = SDRAM_MODE | 0x04000000;
- __asm__ volatile ("sync");
-#endif /* SDRAM_DDR */
-
- /* precharge all banks */
- *(vu_long *) MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000002 |
hi_addr_bit;
- __asm__ volatile ("sync");
-
- /* auto refresh */
- *(vu_long *) MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | 0x80000004 |
hi_addr_bit;
- __asm__ volatile ("sync");
-
- /* set mode register */
- *(vu_long *) MPC5XXX_SDRAM_MODE = SDRAM_MODE;
- __asm__ volatile ("sync");
-
- /* normal operation */
- *(vu_long *) MPC5XXX_SDRAM_CTRL = SDRAM_CONTROL | hi_addr_bit;
- __asm__ volatile ("sync");
-}
-#endif /* !CONFIG_SYS_RAMBOOT */
-
-
-phys_size_t initdram(int board_type)
-{
- ulong dramsize = 0;
- ulong dramsize2 = 0;
- uint svr, pvr;
-
-#ifndef CONFIG_SYS_RAMBOOT
- ulong test1, test2;
-
- /* setup SDRAM chip selects */
- *(vu_long *) MPC5XXX_SDRAM_CS0CFG = 0x0000001e; /* 2G at 0x0 */
- *(vu_long *) MPC5XXX_SDRAM_CS1CFG = 0x80000000; /* disabled */
- __asm__ volatile ("sync");
-
- /* setup config registers */
- *(vu_long *) MPC5XXX_SDRAM_CONFIG1 = SDRAM_CONFIG1;
- *(vu_long *) MPC5XXX_SDRAM_CONFIG2 = SDRAM_CONFIG2;
- __asm__ volatile ("sync");
-
-#if SDRAM_DDR
- /* set tap delay */
- *(vu_long *) MPC5XXX_CDM_PORCFG = SDRAM_TAPDELAY;
- __asm__ volatile ("sync");
-#endif /* SDRAM_DDR */
-
- /* find RAM size using SDRAM CS0 only */
- sdram_start(0);
- test1 = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, 0x80000000);
- sdram_start(1);
- test2 = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, 0x80000000);
- if (test1 > test2) {
- sdram_start(0);
- dramsize = test1;
- } else
- dramsize = test2;
-
- /* memory smaller than 1MB is impossible */
- if (dramsize < (1 << 20))
- dramsize = 0;
-
- /* set SDRAM CS0 size according to the amount of RAM found */
- if (dramsize > 0)
- *(vu_long *) MPC5XXX_SDRAM_CS0CFG = 0x13 +
__builtin_ffs(dramsize >> 20) - 1;
- else
- *(vu_long *) MPC5XXX_SDRAM_CS0CFG = 0; /* disabled */
-
- /* let SDRAM CS1 start right after CS0 */
- *(vu_long *) MPC5XXX_SDRAM_CS1CFG = dramsize + 0x0000001e;/* 2G */
-
- /* find RAM size using SDRAM CS1 only */
- if (!dramsize)
- sdram_start(0);
- test2 = test1 = get_ram_size((long *) (CONFIG_SYS_SDRAM_BASE +
dramsize), 0x80000000);
- if (!dramsize) {
- sdram_start(1);
- test2 = get_ram_size((long *) (CONFIG_SYS_SDRAM_BASE +
dramsize), 0x80000000);
- }
- if (test1 > test2) {
- sdram_start(0);
- dramsize2 = test1;
- } else
- dramsize2 = test2;
-
- /* memory smaller than 1MB is impossible */
- if (dramsize2 < (1 << 20))
- dramsize2 = 0;
-
- /* set SDRAM CS1 size according to the amount of RAM found */
- if (dramsize2 > 0)
- *(vu_long *) MPC5XXX_SDRAM_CS1CFG = dramsize
- | (0x13 + __builtin_ffs(dramsize2 >> 20) - 1);
- else
- *(vu_long *) MPC5XXX_SDRAM_CS1CFG = dramsize; /* disabled */
-
-#else /* CONFIG_SYS_RAMBOOT */
-
- /* retrieve size of memory connected to SDRAM CS0 */
- dramsize = *(vu_long *) MPC5XXX_SDRAM_CS0CFG & 0xFF;
- if (dramsize >= 0x13)
- dramsize = (1 << (dramsize - 0x13)) << 20;
- else
- dramsize = 0;
-
- /* retrieve size of memory connected to SDRAM CS1 */
- dramsize2 = *(vu_long *) MPC5XXX_SDRAM_CS1CFG & 0xFF;
- if (dramsize2 >= 0x13)
- dramsize2 = (1 << (dramsize2 - 0x13)) << 20;
- else
- dramsize2 = 0;
-
-#endif /* CONFIG_SYS_RAMBOOT */
-
- /*
- * On MPC5200B we need to set the special configuration delay in the
- * DDR controller. Please refer to Freescale's AN3221 "MPC5200B SDRAM
- * Initialization and Configuration", 3.3.1 SDelay--MBAR + 0x0190:
- *
- * "The SDelay should be written to a value of 0x00000004. It is
- * required to account for changes caused by normal wafer processing
- * parameters."
- */
- svr = get_svr();
- pvr = get_pvr();
- if ((SVR_MJREV(svr) >= 2) &&
- (PVR_MAJ(pvr) == 1) && (PVR_MIN(pvr) == 4)) {
-
- *(vu_long *) MPC5XXX_SDRAM_SDELAY = 0x04;
- __asm__ volatile ("sync");
- }
-
- return dramsize + dramsize2;
-}
-
-
-int checkboard (void)
-{
- puts("Board: MarelV38B\n");
- return 0;
-}
-
-int board_early_init_f(void)
-{
-#ifdef CONFIG_HW_WATCHDOG
- /*
- * Enable and configure the direction (output) of PSC3_9 - watchdog
- * reset input. Refer to 7.3.2.2.[1,3,4] of the MPC5200B User's
- * Manual.
- */
- *(vu_long *) MPC5XXX_WU_GPIO_ENABLE |= GPIO_PSC3_9;
- *(vu_long *) MPC5XXX_WU_GPIO_DIR |= GPIO_PSC3_9;
-#endif /* CONFIG_HW_WATCHDOG */
- return 0;
-}
-
-int board_early_init_r(void)
-{
- /*
- * Now, when we are in RAM, enable flash write access for the
- * detection process. Note that CS_BOOT cannot be cleared when
- * executing in flash.
- */
- *(vu_long *) MPC5XXX_BOOTCS_CFG &= ~0x1; /* clear RO */
-
- /*
- * Enable GPIO_WKUP_7 to "read the status of the actual power
- * situation". Default direction is input, so no need to set it
- * explicitly.
- */
- *(vu_long *) MPC5XXX_WU_GPIO_ENABLE |= GPIO_WKUP_7;
- return 0;
-}
-
-extern void board_get_enetaddr(uchar *enetaddr);
-int misc_init_r(void)
-{
- uchar enetaddr[6];
-
- if (!eth_getenv_enetaddr("ethaddr", enetaddr)) {
- board_get_enetaddr(enetaddr);
- eth_setenv_enetaddr("ethaddr", enetaddr);
- }
-
- return 0;
-}
-
-#if defined(CONFIG_CMD_IDE) && defined(CONFIG_IDE_RESET)
-void init_ide_reset(void)
-{
- debug("init_ide_reset\n");
-
- /* Configure PSC1_4 as GPIO output for ATA reset */
- *(vu_long *) MPC5XXX_WU_GPIO_ENABLE |= GPIO_PSC1_4;
- *(vu_long *) MPC5XXX_WU_GPIO_DIR |= GPIO_PSC1_4;
- /* Deassert reset */
- *(vu_long *) MPC5XXX_WU_GPIO_DATA_O |= GPIO_PSC1_4;
-}
-
-
-void ide_set_reset(int idereset)
-{
- debug("ide_reset(%d)\n", idereset);
-
- if (idereset) {
- *(vu_long *) MPC5XXX_WU_GPIO_DATA_O &= ~GPIO_PSC1_4;
- /* Make a delay. MPC5200 spec says 25 usec min */
- udelay(500000);
- } else
- *(vu_long *) MPC5XXX_WU_GPIO_DATA_O |= GPIO_PSC1_4;
-}
-#endif
-
-
-#ifdef CONFIG_HW_WATCHDOG
-void hw_watchdog_reset(void)
-{
- /*
- * MarelV38B has a TPS3705 watchdog. Spec says that to kick the dog
- * we need a positive or negative transition on WDI i.e., our PSC3_9.
- */
- *(vu_long *) MPC5XXX_WU_GPIO_DATA_O ^= GPIO_PSC3_9;
-}
-#endif /* CONFIG_HW_WATCHDOG */
diff --git a/configs/v38b_defconfig b/configs/v38b_defconfig
deleted file mode 100644
index cc3d802..0000000
--- a/configs/v38b_defconfig
+++ /dev/null
@@ -1,4 +0,0 @@
-CONFIG_PPC=y
-CONFIG_MPC5xxx=y
-CONFIG_TARGET_V38B=y
-# CONFIG_CMD_SETEXPR is not set
diff --git a/include/configs/v38b.h b/include/configs/v38b.h
deleted file mode 100644
index 63049ab..0000000
--- a/include/configs/v38b.h
+++ /dev/null
@@ -1,333 +0,0 @@
-/*
- * (C) Copyright 2003-2006 Wolfgang Denk, DENX Software Engineering,
- * w...@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-#define CONFIG_MPC5200 1 /* This is an MPC5200 CPU */
-#define CONFIG_V38B 1 /* ...on V38B board */
-
-#define CONFIG_SYS_TEXT_BASE 0xFF000000
-
-#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ...running at
33.000000MHz */
-
-#define CONFIG_RTC_PCF8563 1 /* has PCF8563 RTC */
-#define CONFIG_MPC5200_DDR 1 /* has DDR SDRAM */
-
-#undef CONFIG_HW_WATCHDOG /* don't use watchdog */
-
-#define CONFIG_NETCONSOLE 1
-
-#define CONFIG_BOARD_EARLY_INIT_R 1 /* do board-specific init */
-#define CONFIG_BOARD_EARLY_INIT_F 1 /* do board-specific init */
-#define CONFIG_MISC_INIT_R
-
-#define CONFIG_SYS_XLB_PIPELINING 1 /* gives better
performance */
-
-#define CONFIG_HIGH_BATS 1 /* High BATs supported */
-
-/*
- * Serial console configuration
- */
-#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */
-#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */
-#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200,
230400 }
-
-/*
- * DDR
- */
-#define SDRAM_DDR 1 /* is DDR */
-/* Settings for XLB = 132 MHz */
-#define SDRAM_MODE 0x018D0000
-#define SDRAM_EMODE 0x40090000
-#define SDRAM_CONTROL 0x704f0f00
-#define SDRAM_CONFIG1 0x73722930
-#define SDRAM_CONFIG2 0x47770000
-#define SDRAM_TAPDELAY 0x10000000
-
-/*
- * PCI - no suport
- */
-#undef CONFIG_PCI
-
-/*
- * Partitions
- */
-#define CONFIG_MAC_PARTITION 1
-#define CONFIG_DOS_PARTITION 1
-
-/*
- * USB
- */
-#define CONFIG_USB_OHCI
-#define CONFIG_USB_STORAGE
-#define CONFIG_USB_CLOCK 0x0001BBBB
-#define CONFIG_USB_CONFIG 0x00001000
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IDE
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_SDRAM
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_USB
-#define CONFIG_CMD_FAT
-
-
-#define CONFIG_TIMESTAMP /* Print image info with timestamp */
-
-/*
- * Boot low with 16 MB Flash
- */
-#define CONFIG_SYS_LOWBOOT 1
-#define CONFIG_SYS_LOWBOOT16 1
-
-/*
- * Autobooting
- */
-#define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
-
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "bootcmd=run net_nfs\0" \
- "bootdelay=3\0" \
- "baudrate=115200\0" \
- "preboot=echo;echo Type \"run flash_nfs\" to mount root " \
- "filesystem over NFS; echo\0" \
- "netdev=eth0\0" \
- "ramargs=setenv bootargs root=/dev/ram rw wdt=off \0" \
- "addip=setenv bootargs $(bootargs) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):" \
- "$(netmask):$(hostname):$(netdev):off panic=1\0" \
- "flash_nfs=run nfsargs addip;bootm $(kernel_addr)\0" \
- "flash_self=run ramargs addip;bootm $(kernel_addr) " \
- "$(ramdisk_addr)\0" \
- "net_nfs=tftp 200000 $(bootfile);run nfsargs addip;bootm\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=$(serverip):$(rootpath) wdt=off\0" \
- "hostname=v38b\0" \
- "ethact=FEC\0" \
- "rootpath=/opt/eldk-3.1.1/ppc_6xx\0" \
- "update=prot off ff000000 ff03ffff; era ff000000 ff03ffff; " \
- "cp.b 200000 ff000000 $(filesize);" \
- "prot on ff000000 ff03ffff\0" \
- "load=tftp 200000 $(u-boot)\0" \
- "netmask=255.255.0.0\0" \
- "ipaddr=192.168.160.18\0" \
- "serverip=192.168.1.1\0" \
- "bootfile=/tftpboot/v38b/uImage\0" \
- "u-boot=/tftpboot/v38b/u-boot.bin\0" \
- ""
-
-#define CONFIG_BOOTCOMMAND "run net_nfs"
-
-/*
- * IPB Bus clocking configuration.
- */
-#undef CONFIG_SYS_IPBCLK_EQUALS_XLBCLK /* define for 133MHz
speed */
-
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */
-#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-
-/*
- * EEPROM configuration
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 70
-
-/*
- * RTC configuration
- */
-#define CONFIG_SYS_I2C_RTC_ADDR 0x51
-
-/*
- * Flash configuration - use CFI driver
- */
-#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI
conformant */
-#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common
driver */
-#define CONFIG_SYS_FLASH_CFI_AMD_RESET 1
-#define CONFIG_SYS_FLASH_BASE 0xFF000000
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash
banks */
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
-#define CONFIG_SYS_FLASH_SIZE 0x01000000 /* 16 MiB */
-#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max num of sects on
one chip */
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* flash write speed-up
*/
-
-/*
- * Environment settings
- */
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x00040000)
-#define CONFIG_ENV_SIZE 0x10000
-#define CONFIG_ENV_SECT_SIZE 0x10000
-#define CONFIG_ENV_OVERWRITE 1
-
-/*
- * Memory map
- */
-#define CONFIG_SYS_MBAR 0xF0000000
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_DEFAULT_MBAR 0x80000000
-
-/* Use SRAM until RAM will be available */
-#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM
-#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE /* Size of used
area in DPRAM */
-
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE -
GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-# define CONFIG_SYS_RAMBOOT 1
-#endif
-
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256kB for
Monitor */
-#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128kB for
malloc() */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Linux initial memory
map */
-
-/*
- * Ethernet configuration
- */
-#define CONFIG_MPC5xxx_FEC 1
-#define CONFIG_MPC5xxx_FEC_MII100
-#define CONFIG_PHY_ADDR 0x00
-#define CONFIG_MII 1
-
-/*
- * GPIO configuration
- */
-#define CONFIG_SYS_GPS_PORT_CONFIG 0x90001404
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
/* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of
command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot
Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM
*/
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address
*/
-
-#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
-#if defined(CONFIG_CMD_KGDB)
-# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above
value */
-#endif
-
-/*
- * Various low-level settings
- */
-#define CONFIG_SYS_HID0_INIT HID0_ICE | HID0_ICFI
-#define CONFIG_SYS_HID0_FINAL HID0_ICE
-
-#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE
-#define CONFIG_SYS_BOOTCS_CFG 0x00047801
-#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE
-
-#define CONFIG_SYS_CS_BURST 0x00000000
-#define CONFIG_SYS_CS_DEADCYCLE 0x33333333
-
-#define CONFIG_SYS_RESET_ADDRESS 0xff000000
-
-/*
- * IDE/ATA (supports IDE harddisk)
- */
-#undef CONFIG_IDE_8xx_PCCARD /* Don't use IDE with PC Card Adapter */
-#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
-#undef CONFIG_IDE_LED /* LED for ide not supported */
-
-#define CONFIG_IDE_RESET /* reset for ide supported */
-#define CONFIG_IDE_PREINIT
-
-#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
-#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
-
-#define CONFIG_SYS_ATA_BASE_ADDR MPC5XXX_ATA
-
-#define CONFIG_SYS_ATA_DATA_OFFSET (0x0060) /* data I/O offset */
-
-#define CONFIG_SYS_ATA_REG_OFFSET (CONFIG_SYS_ATA_DATA_OFFSET) /*
normal register accesses offset */
-
-#define CONFIG_SYS_ATA_ALT_OFFSET (0x005C) /* alternate registers
offset */
-
-#define CONFIG_SYS_ATA_STRIDE 4 /* Interval between
registers */
-
-/*
- * Status LED
- */
-#define CONFIG_STATUS_LED /* Status LED enabled */
-#define CONFIG_BOARD_SPECIFIC_LED /* version has board specific leds */
-
-#define CONFIG_SYS_LED_BASE MPC5XXX_GPT7_ENABLE /* Timer 7 GPIO */
-#ifndef __ASSEMBLY__
-typedef unsigned int led_id_t;
-
-#define __led_toggle(_msk) \
- do { \
- *((volatile long *) (CONFIG_SYS_LED_BASE)) ^= (_msk); \
- } while(0)
-
-#define __led_set(_msk, _st) \
- do { \
- if ((_st)) \
- *((volatile long *) (CONFIG_SYS_LED_BASE)) &= ~(_msk); \
- else \
- *((volatile long *) (CONFIG_SYS_LED_BASE)) |= (_msk); \
- } while(0)
-
-#define __led_init(_msk, st) \
- do { \
- *((volatile long *) (CONFIG_SYS_LED_BASE)) |= 0x34; \
- } while(0)
-#endif /* __ASSEMBLY__ */
-
-#endif /* __CONFIG_H */
--
1.9.1
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
