Hello Michal,

Op 07-06-15 om 18:48 schreef Michal Suchanek:
Hello,

On 5 June 2015 at 13:52, Roy Spliet <r.spl...@ultimaker.com> wrote:
Based on the default layout of the android image used at least on Olimex Lime

Signed-off-by: Roy Spliet <r.spl...@ultimaker.com>
---
  include/configs/sunxi-common.h | 9 +++++++++
  1 file changed, 9 insertions(+)

diff --git a/include/configs/sunxi-common.h b/include/configs/sunxi-common.h
index ec28c40..b38f2f5 100644
--- a/include/configs/sunxi-common.h
+++ b/include/configs/sunxi-common.h
@@ -404,8 +404,15 @@ extern int soft_i2c_gpio_scl;
  #define BOOT_TARGET_DEVICES_USB(func)
  #endif

+#ifdef CONFIG_NAND
+#define BOOT_TARGET_DEVICES_NAND(func) func(NAND, nand , 0)
+#else
+#define BOOT_TARGET_DEVICES_NAND(func)
+#endif
+
  #define BOOT_TARGET_DEVICES(func) \
         BOOT_TARGET_DEVICES_MMC(func) \
+       BOOT_TARGET_DEVICES_NAND(func) \
         BOOT_TARGET_DEVICES_SCSI(func) \
         BOOT_TARGET_DEVICES_USB(func) \
         func(PXE, pxe, na) \
@@ -441,6 +448,8 @@ extern int soft_i2c_gpio_scl;
         MEM_LAYOUT_ENV_SETTINGS \
         "fdtfile=" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0" \
         "console=ttyS0,115200\0" \
+       "mtdids=nand0=mtd2\0" \
+       "mtdparts=mtdparts=mtd2:0xffc00000@0x400000(nand0_main)\0" \
         BOOTENV
 From what I heard the nand boot partition size should be specified in
nand pages rather than bytes because the boot rom loads a fixed number
of pages and just uses the start of each page regardless of page size.
Although I believe you have the facts mostly right, they do not apply in this situation. What you are looking for is the partition definition for U-boot. At this point the boot rom (BROM) is no longer active and thus it's inner workings are mostly irrelevant. The NAND partition lay-out for the boards I have seen (various Olimex + Cubietruck..)
are as follows:
0-2MB U-Boot-SPL + U-Boot
2-4MB U-Boot SPL + U-Boot (for recovery)
4MB+ Main file system

The mtdparts env variable defines only the main file system because that's the only
place with relevant files for U-Boot.
This said: I have replaced the default file system with a "custom" UBI FS containing just a boot and a rootfs partition. I am unsure whether these defaults apply for the Android image that ships with the Olimex boards. But then again: that image also
ships with a boot-loader, so do we care?
I did not find any document regarding the nand boot partition layout
so I would like to see some input from somebody familiar with the
driver.

While it is fine for testing to hand-edit the environment the final
nand support should have

1) way to express the boot partition size in nand pages
2) way to make the main partition start at the end of boot partition
and extend to the end of the flash

This should probably also go to Linux.
Linux can define partitions in the device tree. I'd prefer to carry this approach to U-boot, but current U-Boot has the partitioning part of the MTD code hacked away and replaced by custom mtdparts code without OF support. Doing this proper requires getting rid of the latter, which will likely break a lot of legacy. So as far as I agree, I have to warn that is a longer-term project, extended further by the ongoing (justified) discussion we are having regarding the MTD partitioning code in upstream Linux that may or may not lead to parts
of the framework being re-architected.

Roy
Thanks

Michal


--


IMAGINE IT >> MAKE IT

Meet us online at Twitter <http://twitter.com/ultimaker>, Facebook <http://facebook.com/ultimaker>, Google+ <http://google.com/+Ultimaker>

www.ultimaker.com
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot

Reply via email to