Fabio,
I added the '#define CONFIG_USB_MAX_CONTROLLER_COUNT 2' to my include config
file and I see that it loads both USB port 0 and 1.
To me it looks like using CONFIG_USB_MAX_CONTROLLER_COUNT produces that number
of duplicate devices all of the USB port defined by CONFIG_MXC_USB_PORT.
If CONFIG_MXC_USB_PORT is set 0, I only get port 0 duplicated
CONFIG_USB_MAX_CONTROLLER_COUNT times. The ums command works, but I don't see
any USB devices connected to port 1.
If CONFIG_MXC_USB_PORT is set 1, I only get port 1 duplicated
CONFIG_USB_MAX_CONTROLLER_COUNT times. The ums command shows nothing on the
host side, but I can see USB devices (although multiple of the same single
device, one on each port)
I looked at drivers/usb/host/ehci-mx5.c and found that the loading of USB is
not dynamic and depends on the CONFIG_MXC_USB_PORT value. In
drivers/usb/host/ehci-hcd.c, the CONFIG_USB_MAX_CONTROLLER_COUNT value defines
how many devices to create and the index of the current device is passed to the
usb_lowlevel_init() function in drivers/usb/host/ehci-mx5.c but is ignored.
Here is the output when running 'usb start' and then 'usb tree' when
CONFIG_MXC_USB_PORT is 1 and CONFIG_USB_MAX_CONTROLLER_COUNT is 2 and a USB
mass storage device is only connected to port 1:
U-Boot > usb start
starting USB...
USB0: USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
USB1: USB EHCI 1.00
scanning bus 1 for devices... 2 USB Device(s) found
scanning usb for storage devices... EHCI timed out on TD -
token=0x80008c80
EHCI timed out on TD - token=0x80008d80
EHCI timed out on TD - token=0x80008d80
EHCI timed out on TD - token=0x80008d80
EHCI timed out on TD - token=0x80008d80
EHCI timed out on TD - token=0x80008d80
error in inquiry
1 Storage Device(s) found
scanning usb for ethernet devices... 0 Ethernet Device(s) found
U-Boot > usb tree
USB device tree:
1 Hub (480 Mb/s, 0mA)
| u-boot EHCI Host Controller
|
+-2 Mass Storage (480 Mb/s, 100mA)
Generic Mass Storage 30820100
3 Hub (480 Mb/s, 0mA)
| u-boot EHCI Host Controller
|
+-4 Mass Storage (480 Mb/s, 100mA)
Generic Mass Storage 30820100
I fixed the issues by switching all instances of CONFIG_MXC_USB_PORT with index
in drivers/usb/host/ehci-mx5.c and CONFIG_MXC_USB_PORT is no longer used. Even
if index is used in place of CONFIG_MXC_USB_PORT, if you wanted to just use
port 1 you would need to populate both port 0 and 1 by setting
CONFIG_USB_MAX_CONTROLLER_COUNT to 2.
Here is the patch I made to drivers/usb/host/ehci-hcd.c to make USB client work
on port 0 and USB host work on port 1 at the same time:
diff --git a/drivers/usb/host/ehci-mx5.c b/drivers/usb/host/ehci-mx5.c
index 7566c61..f7ecff5 100644
--- a/drivers/usb/host/ehci-mx5.c
+++ b/drivers/usb/host/ehci-mx5.c
@@ -231,10 +231,10 @@ int ehci_hcd_init(int index, enum usb_init_type init,
mdelay(1);
/* Do board specific initialization */
- board_ehci_hcd_init(CONFIG_MXC_USB_PORT);
+ board_ehci_hcd_init(index);
ehci = (struct usb_ehci *)(OTG_BASE_ADDR +
- (0x200 * CONFIG_MXC_USB_PORT));
+ (0x200 * index));
*hccr = (struct ehci_hccr *)((uint32_t)&ehci->caplength);
*hcor = (struct ehci_hcor *)((uint32_t)*hccr +
HC_LENGTH(ehci_readl(&(*hccr)->cr_capbase)));
@@ -243,11 +243,11 @@ int ehci_hcd_init(int index, enum usb_init_type init,
__raw_writel(CONFIG_MXC_USB_PORTSC, &ehci->portsc);
setbits_le32(&ehci->portsc, USB_EN);
- mxc_set_usbcontrol(CONFIG_MXC_USB_PORT, CONFIG_MXC_USB_FLAGS);
+ mxc_set_usbcontrol(index, CONFIG_MXC_USB_FLAGS);
mdelay(10);
/* Do board specific post-initialization */
- board_ehci_hcd_postinit(ehci, CONFIG_MXC_USB_PORT);
+ board_ehci_hcd_postinit(ehci, index);
return 0;
}
Regards,
Matthew Starr
> -----Original Message-----
> From: Fabio Estevam [mailto:feste...@gmail.com]
> Sent: Tuesday, May 19, 2015 9:45 PM
> To: Matthew Starr
> Cc: U-Boot-Denx; Marek VaĊĦut
> Subject: Re: [U-Boot] i.MX53 USB Client not working
>
> Hi Matthew,
>
> On Thu, May 14, 2015 at 7:39 PM, Matthew Starr <mst...@hedonline.com>
> wrote:
> > It appears that setting CONFIG_MXC_USB_PORT to 0 then loads the OTG
> port on the i.MX53. The code appears to be in drivers/usb/host/ehci-mx5.c.
> The problem then is that the USB host port is then not usable since my
> i.MX53 board dedicates the OTG port to USB client functionality only.
> >
> > Now I am trying to get both USB Host port 1 and USB OTG port 0 working at
> the same time. Does u-boot allow using multiple USB controller ports at the
> same time?
>
> Yes, you can use both ports.
>
> In order to do so, you need to pass #define
> CONFIG_USB_MAX_CONTROLLER_COUNT 2 in your config file.
>
> Regards,
>
> Fabio Estevam
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
