This reverts commit 17da7120249bfdef877f46be5bbcb3cc01212eb9.

The i210/i211 do have the SW_FW_SYNC (0x5b5c) register and this is what should
be used when acquiring the semaphore.

I believe the issue that this patch was trying to resolve is now resolved
by properly releasing the semaphore once no longer needed.

Cc: Marcel Ziswiler <mar...@ziswiler.com>
Cc: Marek Vasut <ma...@denx.de>
Cc: Aneesh Bansal <aneesh.ban...@freescale.com>
Cc: Naveen Burmi <naveenbu...@freescale.com>
Cc: Po Liu <po....@freescale.com>
Cc: Bin Meng <bmeng...@gmail.com>
Cc: Alison Wang <alison.w...@freescale.com>
Cc: Reinhard Arlt <reinhard.a...@esd-electronics.com>
Cc: Shengzhou Liu  <shengzhou....@freescale.com>
Cc: York Sun <york...@freescale.com>
Signed-off-by: Tim Harvey <thar...@gateworks.com>
---
 drivers/net/e1000.c | 6 ++----
 drivers/net/e1000.h | 1 -
 2 files changed, 2 insertions(+), 5 deletions(-)

diff --git a/drivers/net/e1000.c b/drivers/net/e1000.c
index a64bc7b..f960024 100644
--- a/drivers/net/e1000.c
+++ b/drivers/net/e1000.c
@@ -1120,10 +1120,7 @@ e1000_swfw_sync_acquire(struct e1000_hw *hw, uint16_t 
mask)
                if (e1000_get_hw_eeprom_semaphore(hw))
                        return -E1000_ERR_SWFW_SYNC;
 
-               if (hw->mac_type == e1000_igb)
-                       swfw_sync = E1000_READ_REG(hw, I210_SW_FW_SYNC);
-               else
-                       swfw_sync = E1000_READ_REG(hw, SW_FW_SYNC);
+               swfw_sync = E1000_READ_REG(hw, SW_FW_SYNC);
                if (!(swfw_sync & (fwmask | swmask)))
                        break;
 
@@ -4458,6 +4455,7 @@ e1000_phy_hw_reset(struct e1000_hw *hw)
 
                if (hw->mac_type >= e1000_82571)
                        mdelay(10);
+
        } else {
                /* Read the Extended Device Control Register, assert the 
PHY_RESET_DIR
                 * bit to put the PHY into reset. Then, take it out of reset.
diff --git a/drivers/net/e1000.h b/drivers/net/e1000.h
index f3b77b1..232c95d 100644
--- a/drivers/net/e1000.h
+++ b/drivers/net/e1000.h
@@ -2496,7 +2496,6 @@ struct e1000_hw {
 #define ICH_GFPREG_BASE_MASK       0x1FFF
 #define ICH_FLASH_LINEAR_ADDR_MASK 0x00FFFFFF
 
-#define E1000_I210_SW_FW_SYNC 0x5B50 /* Software-Firmware Synchronization - RW 
*/
 #define E1000_SW_FW_SYNC 0x05B5C /* Software-Firmware Synchronization - RW */
 
 /* SPI EEPROM Status Register */
-- 
1.9.1

_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot

Reply via email to