On Fri, May 15, 2015 at 7:25 AM, Stefano Babic <sba...@denx.de> wrote: > Hi Tim, > > On 09/05/2015 03:28, Tim Harvey wrote: >> This collection of patches comprises a set of various updates I've been >> on for Ventana. >> >> In summary: >> - enable driver model >> - enable gpio command >> - enable dm-serial >> - enable thermal support >> - fixup for GW522x PCI enumeration >> - split out common code shared between SPL an U-Boot >> - pull down various init code to the SPL for use in Falcon mode >> - enable Falcon mode (based on env var) >> >> The enabling of Falcon mode is dependent on a patch I submitted earlier >> allowing nand env in spl [1]. >> >> Currently Falcon mode is configured for NAND boot. I plan on re-working >> a pending patchset I have that allows dynamic env support (use mmc or nand >> env depending on boot device) but I still need to re-work that using >> driver-model so it will come later. >> >> I will send a followup patch with README updates explaining our use of Falcon >> mode if everything here looks good. >> >> Tim >> >> [1] https://patchwork.ozlabs.org/patch/470191/ >> >> Tim Harvey (19): >> imx: ventana: set dtype env var to boot media >> imx: ventana: display SPL boot device >> imx: ventana: config: enable gpio command >> imx: ventana: config: enable driver model >> imx: ventana: register gpio's with gpio_request >> imx: ventana: enable DM_SERIAL >> imx: ventana: config: enable Thermal support >> imx: ventana: config: use MMC SPL RAW support >> imx: ventana: (cosmetic) clean up size defines for improved >> readability >> imx: ventana: fix pcie reset for GW522x >> imx: ventana: default msata/pci mux to pci before PCI enumeration >> imx: ventana: split out common functions between SPL and uboot >> imx: ventana: move GSC boot watchdog disable function to gsc.c >> imx: ventana: detect pmic using i2c probe instead of board model >> imx: ventana: use common uart and i2c setup functions in SPL >> imx: ventana: add gpio setup to SPL >> imx: ventana: add pmic_setup to SPL >> imx: ventana: add GSC boot watchdog disable to SPL >> imx: ventana: config: enable Falcon mode >> >> board/gateworks/gw_ventana/Makefile | 2 +- >> board/gateworks/gw_ventana/common.c | 827 +++++++++++++++++++++++++ >> board/gateworks/gw_ventana/common.h | 98 +++ >> board/gateworks/gw_ventana/gsc.c | 27 + >> board/gateworks/gw_ventana/gsc.h | 1 + >> board/gateworks/gw_ventana/gw_ventana.c | 911 >> ++-------------------------- >> board/gateworks/gw_ventana/gw_ventana_spl.c | 103 ++-- >> include/configs/gw_ventana.h | 67 +- >> 8 files changed, 1102 insertions(+), 934 deletions(-) >> create mode 100644 board/gateworks/gw_ventana/common.c >> create mode 100644 board/gateworks/gw_ventana/common.h >> > > Patches 1-7, 10-16, 18 applied to u-boot-imx, thanks ! > > Best regards, > Stefano Babic >
Stefano, Thanks - I just posted a v2 of patch 8 and a rebased 9 and 17 (assuming that is why you skipped those two). You were right to hold off on 19 as it will fail to compile until 'env_nand: use nand_spl_load_image for readenv if SPL' [1] is accepted which I sent to Scott as he's the nand maintainer - he's given a thumbs up but may be waiting for additional feedback (or perhaps waiting on my attempted simplification of readenv which I've about lost interest on as its just a simplification and apparently I don't understand the args to nand_read_skip_bad). Tim [1] - https://patchwork.ozlabs.org/patch/472491/ _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot
