Hi Nikolay,
On 22/04/2015 14:22, Nikolay Dimitrov wrote:
> Hi Stefano,
>
> On 04/22/2015 03:12 PM, Stefano Babic wrote:
>> Hi Nikolay,
>>
>> On 17/04/2015 00:36, Nikolay Dimitrov wrote:
>>> This is proposal for clamping the MMDC/DDR3 clocks to the maximum
>>> supported
>>> frequencies as per imx6 SOC models, and for dynamically calculating
>>> valid
>>> clock value based on mem_speed.
>>>
>>> Currently the code uses impossible values for mem_speed (1333, 1600
>>> MT/s) for
>>> calculating the DDR timings, and uses fixed clock (528 or 400 MHz) which
>>> doesn't take into account DDR3 memory limitations.
>>>
>>> Signed-off-by: Nikolay Dimitrov <picmas...@mail.bg>
>>> Cc: Fabio Estevam <feste...@gmail.com>
>>> Cc: Stefano Babic <sba...@denx.de>
>>> Cc: Tim Harvey <thar...@gateworks.com>
>>> Cc: Eric Nelson <eric.nel...@boundarydevices.com>
>>> ---
>>> arch/arm/cpu/armv7/mx6/ddr.c | 25 ++++++++++++++++++++-----
>>> 1 file changed, 20 insertions(+), 5 deletions(-)
>>>
>>> diff --git a/arch/arm/cpu/armv7/mx6/ddr.c b/arch/arm/cpu/armv7/mx6/ddr.c
>>> index fef2231..9daa180 100644
>>> --- a/arch/arm/cpu/armv7/mx6/ddr.c
>>> +++ b/arch/arm/cpu/armv7/mx6/ddr.c
>>> @@ -265,7 +265,7 @@ void mx6_dram_cfg(const struct mx6_ddr_sysinfo
>>> *sysinfo,
>>> u16 tdllk = 0x1ff; /* DLL locking time: 512 cycles (JEDEC DDR3) */
>>> u8 coladdr;
>>> int clkper; /* clock period in picoseconds */
>>> - int clock; /* clock freq in mHz */
>>> + int clock; /* clock freq in MHz */
>>> int cs;
>>>
>>> mmdc0 = (struct mmdc_p_regs *)MMDC_P0_BASE_ADDR;
>>> @@ -273,16 +273,31 @@ void mx6_dram_cfg(const struct mx6_ddr_sysinfo
>>> *sysinfo,
>>> mmdc1 = (struct mmdc_p_regs *)MMDC_P1_BASE_ADDR;
>>> #endif
>>>
>>> - /* MX6D/MX6Q: 1066 MHz memory clock, clkper = 1.894ns = 1894ps */
>>> + /* Limit mem_speed for MX6D/MX6Q */
>>> if (is_cpu_type(MXC_CPU_MX6Q) || is_cpu_type(MXC_CPU_MX6D)) {
>>> - clock = 528;
>>> + if (ddr3_cfg->mem_speed > 1066)
>>> + ddr3_cfg->mem_speed = 1066; /* 1066 MT/s */
>>> +
Sorry, but there is an issue. Parameters are const struct *, and you are
setting value here.
By testing I get on most mx6 boards:
+arch/arm/cpu/armv7/mx6/ddr.c: In function 'mx6_dram_cfg':
+arch/arm/cpu/armv7/mx6/ddr.c:279:4: error: assignment of member
'mem_speed' in read-only object
+arch/arm/cpu/armv7/mx6/ddr.c:286:4: error: assignment of member
'mem_speed' in read-only object
+make[4]: *** [spl/arch/arm/cpu/armv7/mx6/ddr.o] Error 1
Best regards,
Stefano
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sba...@denx.de
=====================================================================
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
