Dieter,
On Mon, 2009-06-22 at 17:01 +0200, Dieter Kiermaier wrote:
> Am Montag 22 Juni 2009 15:08:20 schrieb Dieter Kiermaier:
>
> This seems to be an issue regarding Gigabit / 100MBits uplink with current
> marvell git u-boot.
this gives lots of things worth looking at them :
- are you running on a custom board, i.e. is MDIO known to work properly
-> PHY adressing ?
- Does your chips require different clocks for 100M/1000M ?
- What about mis-strapped link advertisement of the PHY ? Maybe 100M-FD
disabled ?
Have you tried mii diagnostics ?
Have a look at common/cmd_mii.c -> "mii info" and "mii dump" should be
your friends.
Regards,
André
>
> If I work with 100MBit/s network show the reported errors.
> With gigabit connection everything seems to be working fine until now.
>
> André, thanks for your help!
> Dieter
>
>
> > Am Montag 22 Juni 2009 14:53:44 schrieb André Schwarz:
> > > On Mon, 2009-06-22 at 14:41 +0200, Dieter Kiermaier wrote:
> > > > André,
> > > >
> > > > > Dieter,
> > > > >
> > > > > On Mon, 2009-06-22 at 14:04 +0200, Dieter Kiermaier wrote:
> > > > > > Hi all,
> > > > > >
> > > > > > I've tried the first time booting a self compiled u-boot from
> > > > > > git.marvell.com U-Boot can be downloaded and started with openocd
> > > > > > quite well.
> > > > > > Boot messages (version is dirty due to a comment in board file):
> > > > > >
> > > > > > U-Boot 2009.06-rc2-02207-g14c575a-dirty (Jun 22 2009 - 13:40:45)
> > > > > > Marvell-Sheevaplug
> > > > > >
> > > > > > SoC: Kirkwood 88F6281_A0
> > > > > > DRAM: 512 MB
> > > > > > NAND: 512 MiB
> > > > > > *** Warning - bad CRC or NAND, using default environment
> > > > >
> > > > > most propably you'll need to save the environment.
> > > >
> > > > Also saving environment doesn't help.
> > > > The bad CRC message disappered as expected but that's all what
> > > > happened.
> > > >
> > > > > > In: serial
> > > > > > Out: serial
> > > > > > Err: serial
> > > > > > Net: egiga0
> > > > > > 88E1116 Initialized on egiga0
> > > > > > Hit any key to stop autoboot: 0
> > > > > > Marvell>>
> > > > >
> > > > > type "save" here and "reset".
> > > > >
> > > > > > Environment is broken only with marvell git u-boot. Preflashed
> > > > > > u-boot find environment is ok.
> > > > > > Does sheevaplug u-boot from marvell git use other environment
> > > > > > settings than preflashed u-boot?
> > > > > >
> > > > > > Marvell>> printenv
> > > > > > bootcmd=${x_bootcmd_kernel}; setenv bootargs ${x_bootargs}
> > > > > > ${x_bootargs_root}; bootm 0x6400000;
> > > > > > bootdelay=3
> > > > > > baudrate=115200
> > > > > > x_bootargs=console=ttyS0,115200
> > > > > > mtdparts=orion_nand:512k(uboot),3...@1m(kernel),1...@4m(psm),1...@5m(roo
> > > > > >tf s) rw x_bootcmd_kernel=nand read 0x100000 0x6400000 0x300000
> > > > > > x_bootargs_root=root=/dev/mtdblock3 rw rootfstype=jffs2
> > > > > > stdin=serial
> > > > > > stdout=serial
> > > > > > stderr=serial
> > > > > > ethaddr=00:50:43:e0:b9:d8
> > > > > > ethact=egiga0
> > > > > > ipaddr=192.168.2.75
> > > > > >
> > > > > > (ipaddr is set after bootup with setenv ipaddr 192.168.2.75)
> > >
> > > Did you try "bootp" or "dhcp" to set up the I/F ?
> >
> > Yes, but everytimes the same:
> > Marvell>> dhcp
> > BOOTP broadcast 1
> >
> > ... machine hangs and only a reset helps...
> >
> >
> > U-Boot 2009.06-rc2-02207-g14c575a-dirty (Jun 22 2009 - 13:40:45)
> > Marvell-Sheevaplug
> >
> > SoC: Kirkwood 88F6281_A0
> > DRAM: 512 MB
> > NAND: 512 MiB
> > *** Warning - bad CRC or NAND, using default environment
> >
> > In: serial
> > Out: serial
> > Err: serial
> > Net: egiga0
> > 88E1116 Initialized on egiga0
> > Hit any key to stop autoboot: 0
> > Marvell>> bootp
> > BOOTP broadcast 1
> >
> > ...the same here again...
> >
> > It seems that the network would be activated (1 blink on the activity LED)
> > but nothing more happens.
> >
> > > > > > If I now try to ping another machine in the same network:
> > > > > > Marvell>> ping 192.168.2.251
> > > > > > Using egiga0 device
> > > > >
> > > > > maybe your MAC is missing ? environment ?
> > > >
> > > > MAC is available in default (compiled in environment) as shown in env
> >
> > above:
> > > > > > ethaddr=00:50:43:e0:b9:d8
> > > >
> > > > Also writing a new MAC to environment / savenenv / reset made no
> > > > difference :(
> > > >
> > > > > > This is all what happens - no response from board, CTRL-C doesn't
> > > > > > work. Only a hard reset will get the board up again.
> > > > > >
> > > > > > Do I have to change something in the default board configuration to
> > > > > > succesfullly use networking on the sheevaplug?
> > > > > >
> > > > > > u-boot is build with following commands:
> > > > > >
> > > > > > make ARCH=arm sheevaplug_config
> > > > > > make
> > > > > >
> > > > > > I get no errors during build.
> > > > > >
> > > > > > My gcc version is:
> > > > > > arm-none-linux-gnueabi-gcc (GCC) 4.2.0 20070413 (prerelease)
> > > > > >
> > > > > > Any help would be appreciated,
> > > > > > Dieter
> > > > >
> > > > > Regards,
> > > > >
> > > > > André
> > > >
> > > > Dieter
> > > >
> > > > > > _______________________________________________
> > > > > > U-Boot mailing list
> > > > > > U-Boot@lists.denx.de
> > > > > > http://lists.denx.de/mailman/listinfo/u-boot
> > > > >
> > > > > MATRIX VISION GmbH, Talstrae 16, DE-71570 Oppenweiler
> > > > > Registergericht: Amtsgericht Stuttgart, HRB 271090
> > > > > Geschftsfhrer: Gerhard Thullner, Werner Armingeon, Uwe Furtner,
> > > > > Hans-Joachim Reich
> > >
> > > MATRIX VISION GmbH, Talstrae 16, DE-71570 Oppenweiler
> > > Registergericht: Amtsgericht Stuttgart, HRB 271090
> > > Geschftsfhrer: Gerhard Thullner, Werner Armingeon, Uwe Furtner,
> > > Hans-Joachim Reich
>
>
MATRIX VISION GmbH, Talstra�e 16, DE-71570 Oppenweiler
Registergericht: Amtsgericht Stuttgart, HRB 271090
Gesch�ftsf�hrer: Gerhard Thullner, Werner Armingeon, Uwe Furtner, Hans-Joachim
Reich
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
