On Sun, 2014-10-12 at 10:43 +0800, Chen-Yu Tsai wrote:
> On Sat, Oct 11, 2014 at 11:58 PM, Ian Campbell <i...@hellion.org.uk> wrote:
> > On Tue, 2014-10-07 at 15:11 +0800, Chen-Yu Tsai wrote:
> >> The basic blocks of the A23 are similar to the A31 (sun6i). Re-use
> >> sun6i code for initial clock, gpio, and uart setup.
> >
> > Do I take it that sun8i is also in the same position wrt DRAM bring up
> > code not existing yet and there therefore being no SPL yet?
>
> That is correct.
Please could you add a sentence to the commit message.
Apart from that: Acked-by: Ian Campbell <i...@hellion.org.uk>
>
> >> Signed-off-by: Chen-Yu Tsai <w...@csie.org>
> >> ---
> >> arch/arm/Kconfig | 3 +++
> >> arch/arm/cpu/armv7/sunxi/Makefile | 2 ++
> >> arch/arm/cpu/armv7/sunxi/board.c | 3 ++-
> >> arch/arm/cpu/armv7/sunxi/cpu_info.c | 2 ++
> >> arch/arm/include/asm/arch-sunxi/clock.h | 2 +-
> >> board/sunxi/Kconfig | 9 ++++++++-
> >> include/configs/sun8i.h | 23 +++++++++++++++++++++++
> >> 7 files changed, 41 insertions(+), 3 deletions(-)
> >> create mode 100644 include/configs/sun8i.h
> >>
> >> diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
> >> index e3e7e78..cb691b2 100644
> >> --- a/arch/arm/Kconfig
> >> +++ b/arch/arm/Kconfig
> >> @@ -450,6 +450,9 @@ config TARGET_SUN6I
> >> config TARGET_SUN7I
> >> bool "Support sun7i"
> >>
> >> +config TARGET_SUN8I
> >> + bool "Support sun8i"
> >> +
> >> config TARGET_SNOWBALL
> >> bool "Support snowball"
> >>
> >> diff --git a/arch/arm/cpu/armv7/sunxi/Makefile
> >> b/arch/arm/cpu/armv7/sunxi/Makefile
> >> index 2a42dca..24f1dae 100644
> >> --- a/arch/arm/cpu/armv7/sunxi/Makefile
> >> +++ b/arch/arm/cpu/armv7/sunxi/Makefile
> >> @@ -12,10 +12,12 @@ obj-y += board.o
> >> obj-y += clock.o
> >> obj-y += pinmux.o
> >> obj-$(CONFIG_SUN6I) += prcm.o
> >> +obj-$(CONFIG_SUN8I) += prcm.o
> >> obj-$(CONFIG_SUN4I) += clock_sun4i.o
> >> obj-$(CONFIG_SUN5I) += clock_sun4i.o
> >> obj-$(CONFIG_SUN6I) += clock_sun6i.o
> >> obj-$(CONFIG_SUN7I) += clock_sun4i.o
> >> +obj-$(CONFIG_SUN8I) += clock_sun6i.o
> >>
> >> ifndef CONFIG_SPL_BUILD
> >> obj-y += cpu_info.o
> >> diff --git a/arch/arm/cpu/armv7/sunxi/board.c
> >> b/arch/arm/cpu/armv7/sunxi/board.c
> >> index 29d45b6..61c1ba9 100644
> >> --- a/arch/arm/cpu/armv7/sunxi/board.c
> >> +++ b/arch/arm/cpu/armv7/sunxi/board.c
> >> @@ -100,7 +100,8 @@ void reset_cpu(ulong addr)
> >> /* do some early init */
> >> void s_init(void)
> >> {
> >> -#if !defined CONFIG_SPL_BUILD && (defined CONFIG_SUN7I || defined
> >> CONFIG_SUN6I)
> >> +#if !defined CONFIG_SPL_BUILD && (defined CONFIG_SUN7I || \
> >> + defined CONFIG_SUN6I || defined CONFIG_SUN8I)
> >
> > At some point we should refactor this to use a common Kconfig thing
> > (SUNXI_SMP etc) which the relevant targets select.
>
> I agree. We can do this as we move further to Kconfig.
>
> ChenYu
>
> >> /* Enable SMP mode for CPU0, by setting bit 6 of Auxiliary Ctl reg */
> >> asm volatile(
> >> "mrc p15, 0, r0, c1, c0, 1\n"
> >> diff --git a/arch/arm/cpu/armv7/sunxi/cpu_info.c
> >> b/arch/arm/cpu/armv7/sunxi/cpu_info.c
> >> index 40c4e13..4f2a09c 100644
> >> --- a/arch/arm/cpu/armv7/sunxi/cpu_info.c
> >> +++ b/arch/arm/cpu/armv7/sunxi/cpu_info.c
> >> @@ -27,6 +27,8 @@ int print_cpuinfo(void)
> >> puts("CPU: Allwinner A31 (SUN6I)\n");
> >> #elif defined CONFIG_SUN7I
> >> puts("CPU: Allwinner A20 (SUN7I)\n");
> >> +#elif defined CONFIG_SUN8I
> >> + puts("CPU: Allwinner A23 (SUN8I)\n");
> >> #else
> >> #warning Please update cpu_info.c with correct CPU information
> >> puts("CPU: SUNXI Family\n");
> >> diff --git a/arch/arm/include/asm/arch-sunxi/clock.h
> >> b/arch/arm/include/asm/arch-sunxi/clock.h
> >> index 8f5d860..012c2af 100644
> >> --- a/arch/arm/include/asm/arch-sunxi/clock.h
> >> +++ b/arch/arm/include/asm/arch-sunxi/clock.h
> >> @@ -15,7 +15,7 @@
> >> #define CLK_GATE_CLOSE 0x0
> >>
> >> /* clock control module regs definition */
> >> -#ifdef CONFIG_SUN6I
> >> +#if defined(CONFIG_SUN6I) || defined(CONFIG_SUN8I)
> >> #include <asm/arch/clock_sun6i.h>
> >> #else
> >> #include <asm/arch/clock_sun4i.h>
> >> diff --git a/board/sunxi/Kconfig b/board/sunxi/Kconfig
> >> index 05defac..16f6db4 100644
> >> --- a/board/sunxi/Kconfig
> >> +++ b/board/sunxi/Kconfig
> >> @@ -27,7 +27,14 @@ config SYS_CONFIG_NAME
> >>
> >> endif
> >>
> >> -if TARGET_SUN4I || TARGET_SUN5I || TARGET_SUN6I || TARGET_SUN7I
> >> +if TARGET_SUN8I
> >> +
> >> +config SYS_CONFIG_NAME
> >> + default "sun8i"
> >> +
> >> +endif
> >> +
> >> +if TARGET_SUN4I || TARGET_SUN5I || TARGET_SUN6I || TARGET_SUN7I ||
> >> TARGET_SUN8I
> >>
> >> config SYS_CPU
> >> default "armv7"
> >> diff --git a/include/configs/sun8i.h b/include/configs/sun8i.h
> >> new file mode 100644
> >> index 0000000..1c1a7cd
> >> --- /dev/null
> >> +++ b/include/configs/sun8i.h
> >> @@ -0,0 +1,23 @@
> >> +/*
> >> + * (C) Copyright 2014 Chen-Yu Tsai <w...@csie.org>
> >> + *
> >> + * Configuration settings for the Allwinner A23 (sun8i) CPU
> >> + *
> >> + * SPDX-License-Identifier: GPL-2.0+
> >> + */
> >> +
> >> +#ifndef __CONFIG_H
> >> +#define __CONFIG_H
> >> +
> >> +/*
> >> + * A23 specific configuration
> >> + */
> >> +#define CONFIG_SUN8I /* sun8i SoC generation */
> >> +#define CONFIG_SYS_PROMPT "sun8i# "
> >> +
> >> +/*
> >> + * Include common sunxi configuration where most the settings are
> >> + */
> >> +#include <configs/sunxi-common.h>
> >> +
> >> +#endif /* __CONFIG_H */
> >
> >
>
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
