Hi Christian,
On 22/09/2014 13:57, Christian Gmeiner wrote:
> This patch adds support for the OT1200 series of devices.
>
> Following components are used in u-boot:
> + ethernet
> + i2c
> + emmc
> + gpio
>
> For more details see README.
>
> Changes v1 > v2
Can you also version your patches in the subject ? (aka: "[PATCH vX]
imx6:..."). Rather patchwork makes some mess and it is not able to
follow the versions, numbering helps - thanks !
There are some warnings reported by checkpatch, a couple opf them are
due to line over 80 chars.
Please fix warnings and repost, thanks !
> - make use of enable_cspi_clock(..)
> - fix usage of OUTPUT_40OHM define
> - added README
>
> Signed-off-by: Christian Gmeiner <christian.gmei...@gmail.com>
> ---
> arch/arm/Kconfig | 4 +
> board/bachmann/ot1200/Kconfig | 23 ++++
> board/bachmann/ot1200/MAINTAINERS | 6 +
> board/bachmann/ot1200/Makefile | 9 ++
> board/bachmann/ot1200/README | 20 +++
> board/bachmann/ot1200/ot1200.c | 251
> ++++++++++++++++++++++++++++++++++++++
> configs/ot1200_defconfig | 3 +
> include/configs/ot1200.h | 196 +++++++++++++++++++++++++++++
> 8 files changed, 512 insertions(+)
> create mode 100644 board/bachmann/ot1200/Kconfig
> create mode 100644 board/bachmann/ot1200/MAINTAINERS
> create mode 100644 board/bachmann/ot1200/Makefile
> create mode 100644 board/bachmann/ot1200/README
> create mode 100644 board/bachmann/ot1200/ot1200.c
> create mode 100644 configs/ot1200_defconfig
> create mode 100644 include/configs/ot1200.h
>
> diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
> index 106aed9..8face21 100644
> --- a/arch/arm/Kconfig
> +++ b/arch/arm/Kconfig
> @@ -414,6 +414,9 @@ config TARGET_HUMMINGBOARD
> config TARGET_TQMA6
> bool "TQ Systems TQMa6 board"
>
> +config TARGET_OT1200
> + bool "Bachmann OT1200"
> +
> config OMAP34XX
> bool "OMAP34XX SoC"
>
> @@ -577,6 +580,7 @@ source "board/atmel/at91sam9rlek/Kconfig"
> source "board/atmel/at91sam9x5ek/Kconfig"
> source "board/atmel/sama5d3_xplained/Kconfig"
> source "board/atmel/sama5d3xek/Kconfig"
> +source "board/bachmann/ot1200/Kconfig"
> source "board/balloon3/Kconfig"
> source "board/barco/titanium/Kconfig"
> source "board/bluegiga/apx4devkit/Kconfig"
> diff --git a/board/bachmann/ot1200/Kconfig b/board/bachmann/ot1200/Kconfig
> new file mode 100644
> index 0000000..55a825d
> --- /dev/null
> +++ b/board/bachmann/ot1200/Kconfig
> @@ -0,0 +1,23 @@
> +if TARGET_OT1200
> +
> +config SYS_CPU
> + string
> + default "armv7"
> +
> +config SYS_BOARD
> + string
> + default "ot1200"
> +
> +config SYS_VENDOR
> + string
> + default "bachmann"
> +
> +config SYS_SOC
> + string
> + default "mx6"
> +
> +config SYS_CONFIG_NAME
> + string
> + default "ot1200"
> +
> +endif
> diff --git a/board/bachmann/ot1200/MAINTAINERS
> b/board/bachmann/ot1200/MAINTAINERS
> new file mode 100644
> index 0000000..ad75c24
> --- /dev/null
> +++ b/board/bachmann/ot1200/MAINTAINERS
> @@ -0,0 +1,6 @@
> +BACHMANN ELECTRONIC OT1200 BOARD
> +M: Christian Gmeiner <christian.gmei...@gmail.com>
> +S: Maintained
> +F: board/bachmann/ot1200
> +F: include/configs/ot1200.h
> +F: configs/ot1200*_defconfig
> diff --git a/board/bachmann/ot1200/Makefile b/board/bachmann/ot1200/Makefile
> new file mode 100644
> index 0000000..1bd42e8
> --- /dev/null
> +++ b/board/bachmann/ot1200/Makefile
> @@ -0,0 +1,9 @@
> +#
> +# Copyright (C) 2012-2013, Guennadi Liakhovetski <l...@denx.de>
> +# (C) Copyright 2012-2013 Freescale Semiconductor, Inc.
> +# Copyright (C) 2013, Boundary Devices <i...@boundarydevices.com>
> +#
> +# SPDX-License-Identifier: GPL-2.0+
> +#
> +
> +obj-y := ot1200.o
> diff --git a/board/bachmann/ot1200/README b/board/bachmann/ot1200/README
> new file mode 100644
> index 0000000..efcff11
> --- /dev/null
> +++ b/board/bachmann/ot1200/README
> @@ -0,0 +1,20 @@
> +U-Boot for the Bachmann electronic GmbH OT1200 devices
> +
> +There are two different versions of the base print,
Do you mean here base board ?
> which differ
> +in the way ethernet is done. The variant detection is done during
> +runtime based on the address of the found phy.
> +
> +- "mr" variant
> +FEC is connected directly to an ethernet switch (KSZ8895). The ethernet
> +port is always up and auto-negotiation is not possible.
> +
> +- normal variant
> +FEC is connected to a normal phy and auto-negotiation is possible.
> +
> +
> +The variant name is part of the dtb file name loaded by u-boot. This
> +make is possible to boot the linux kernel and make use variant specific
> +devicetree (fixed-phy link).
> +
> +In order to support different display resoltuions/sizes the OT1200 devices
> +are making use of EDID data stored in an i2c EEPROM.
> \ No newline at end of file
> diff --git a/board/bachmann/ot1200/ot1200.c b/board/bachmann/ot1200/ot1200.c
> new file mode 100644
> index 0000000..0d5ede5
> --- /dev/null
> +++ b/board/bachmann/ot1200/ot1200.c
> @@ -0,0 +1,251 @@
> +/*
> + * Copyright (C) 2010-2013 Freescale Semiconductor, Inc.
> + * Copyright (C) 2014, Bachmann electronic GmbH
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#include <common.h>
> +#include <asm/arch/clock.h>
> +#include <asm/arch/imx-regs.h>
> +#include <asm/arch/iomux.h>
> +#include <malloc.h>
> +#include <asm/arch/mx6-pins.h>
> +#include <asm/imx-common/iomux-v3.h>
> +#include <asm/imx-common/mxc_i2c.h>
> +#include <asm/imx-common/boot_mode.h>
> +#include <asm/arch/crm_regs.h>
> +#include <mmc.h>
> +#include <fsl_esdhc.h>
> +#include <netdev.h>
> +#include <i2c.h>
> +#include <pca953x.h>
> +#include <asm/gpio.h>
> +#include <phy.h>
> +
> +DECLARE_GLOBAL_DATA_PTR;
> +
> +#define OUTPUT_40OHM (PAD_CTL_SPEED_MED|PAD_CTL_DSE_40ohm)
> +
> +#define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
> + OUTPUT_40OHM | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
> +
> +#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP | \
> + PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm | \
> + PAD_CTL_SRE_FAST | PAD_CTL_HYS)
> +
> +#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | OUTPUT_40OHM | \
> + PAD_CTL_HYS)
> +
> +#define SPI_PAD_CTRL (PAD_CTL_HYS | OUTPUT_40OHM | \
> + PAD_CTL_SRE_FAST)
> +
> +#define I2C_PAD_CTRL (PAD_CTL_PUS_100K_UP | OUTPUT_40OHM | \
> + PAD_CTL_HYS | PAD_CTL_ODE | PAD_CTL_SRE_FAST)
> +
> +int dram_init(void)
> +{
> + gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
> +
> + return 0;
> +}
> +
> +static iomux_v3_cfg_t const uart1_pads[] = {
> + MX6_PAD_CSI0_DAT10__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
> + MX6_PAD_CSI0_DAT11__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
> +};
> +
> +static void setup_iomux_uart(void)
> +{
> + imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
> +}
> +
> +static iomux_v3_cfg_t const enet_pads[] = {
> + MX6_PAD_KEY_ROW1__ENET_COL | MUX_PAD_CTRL(ENET_PAD_CTRL),
> + MX6_PAD_KEY_COL3__ENET_CRS | MUX_PAD_CTRL(ENET_PAD_CTRL),
> + MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
> + MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
> + MX6_PAD_GPIO_16__ENET_REF_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL),
> + MX6_PAD_GPIO_18__ENET_RX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL),
> + MX6_PAD_ENET_RXD0__ENET_RX_DATA0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
> + MX6_PAD_ENET_RXD1__ENET_RX_DATA1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
> + MX6_PAD_KEY_COL2__ENET_RX_DATA2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
> + MX6_PAD_KEY_COL0__ENET_RX_DATA3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
> + MX6_PAD_ENET_CRS_DV__ENET_RX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
> + MX6_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL),
> + MX6_PAD_ENET_TXD0__ENET_TX_DATA0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
> + MX6_PAD_ENET_TXD1__ENET_TX_DATA1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
> + MX6_PAD_KEY_ROW2__ENET_TX_DATA2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
> + MX6_PAD_KEY_ROW0__ENET_TX_DATA3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
> + MX6_PAD_ENET_TX_EN__ENET_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
> +};
> +
> +static void setup_iomux_enet(void)
> +{
> + imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
> +}
> +
> +static iomux_v3_cfg_t const ecspi1_pads[] = {
> + MX6_PAD_DISP0_DAT3__ECSPI3_SS0 | MUX_PAD_CTRL(SPI_PAD_CTRL),
> + MX6_PAD_DISP0_DAT4__ECSPI3_SS1 | MUX_PAD_CTRL(SPI_PAD_CTRL),
> + MX6_PAD_DISP0_DAT2__ECSPI3_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
> + MX6_PAD_DISP0_DAT1__ECSPI3_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
> + MX6_PAD_DISP0_DAT0__ECSPI3_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
> +};
> +
> +static void setup_iomux_spi(void)
> +{
> + imx_iomux_v3_setup_multiple_pads(ecspi1_pads, ARRAY_SIZE(ecspi1_pads));
> +}
> +
> +int board_early_init_f(void)
> +{
> + setup_iomux_uart();
> + setup_iomux_spi();
> +
> + return 0;
> +}
> +
> +static iomux_v3_cfg_t const usdhc3_pads[] = {
> + MX6_PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
> + MX6_PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
> + MX6_PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
> + MX6_PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
> + MX6_PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
> + MX6_PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
> + MX6_PAD_SD3_DAT4__SD3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
> + MX6_PAD_SD3_DAT5__SD3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
> + MX6_PAD_SD3_DAT6__SD3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
> + MX6_PAD_SD3_DAT7__SD3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
> + MX6_PAD_SD3_RST__SD3_RESET | MUX_PAD_CTRL(USDHC_PAD_CTRL),
> +};
> +
> +int board_mmc_getcd(struct mmc *mmc)
> +{
> + return 1;
> +}
> +
> +struct fsl_esdhc_cfg usdhc_cfg[] = {
> + {USDHC3_BASE_ADDR},
> +};
> +
> +int board_mmc_init(bd_t *bis)
> +{
> + usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
> + usdhc_cfg[0].max_bus_width = 8;
> +
> + imx_iomux_v3_setup_multiple_pads(usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
> +
> + return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
> +}
> +
> +#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
> +
> +/* I2C3 - IO expander */
> +static struct i2c_pads_info i2c_pad_info2 = {
> + .scl = {
> + .i2c_mode = MX6_PAD_EIM_D17__I2C3_SCL | PC,
> + .gpio_mode = MX6_PAD_EIM_D17__GPIO3_IO17 | PC,
> + .gp = IMX_GPIO_NR(3, 17)
> + },
> + .sda = {
> + .i2c_mode = MX6_PAD_EIM_D18__I2C3_SDA | PC,
> + .gpio_mode = MX6_PAD_EIM_D18__GPIO3_IO18 | PC,
> + .gp = IMX_GPIO_NR(3, 18)
> + }
> +};
> +
> +static iomux_v3_cfg_t const pwm_pad[] = {
> + MX6_PAD_SD1_CMD__PWM4_OUT | MUX_PAD_CTRL(OUTPUT_40OHM),
> +};
> +
> +static void leds_on(void)
> +{
> + /* turn on all possible leds connected via GPIO expander */
> + i2c_set_bus_num(2);
> + pca953x_set_dir(CONFIG_SYS_I2C_PCA953X_ADDR, 0xffff, PCA953X_DIR_OUT);
> + pca953x_set_val(CONFIG_SYS_I2C_PCA953X_ADDR, 0xffff, 0x0);
> +}
> +
> +static void backlight_lcd_off(void)
> +{
> + unsigned gpio = IMX_GPIO_NR(2, 0);
> + gpio_direction_output(gpio, 0);
> +
> + gpio = IMX_GPIO_NR(2, 3);
> + gpio_direction_output(gpio, 0);
> +}
> +
> +int board_eth_init(bd_t *bis)
> +{
> + uint32_t base = IMX_FEC_BASE;
> + struct mii_dev *bus = NULL;
> + struct phy_device *phydev = NULL;
> + int ret;
> +
> + setup_iomux_enet();
> +
> + bus = fec_get_miibus(base, -1);
> + if (!bus)
> + return 0;
> +
> + /* scan phy 0 and 5 */
> + phydev = phy_find_by_mask(bus, 0x21, PHY_INTERFACE_MODE_RGMII);
> + if (!phydev) {
> + free(bus);
> + return 0;
> + }
> +
> + /* depending on the phy address we can detect our board version */
> + if (phydev->addr == 0)
> + setenv("boardver", "");
> + else
> + setenv("boardver", "mr");
> +
> + printf("using phy at %d\n", phydev->addr);
> + ret = fec_probe(bis, -1, base, bus, phydev);
> + if (ret) {
> + printf("FEC MXC: %s:failed\n", __func__);
> + free(phydev);
> + free(bus);
> + }
> + return 0;
> +}
> +
> +int board_init(void)
> +{
> + gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
> +
> + backlight_lcd_off();
> +
> + setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2);
> +
> + leds_on();
> +
> + /* enable ecspi3 clocks */
> + enable_cspi_clock(1, 2);
> +
> + return 0;
> +}
> +
> +int checkboard(void)
> +{
> + puts("Board: "CONFIG_SYS_BOARD"\n");
> + return 0;
> +}
> +
> +#ifdef CONFIG_CMD_BMODE
> +static const struct boot_mode board_boot_modes[] = {
> + /* 4 bit bus width */
> + {"mmc0", MAKE_CFGVAL(0x40, 0x30, 0x00, 0x00)},
> + {NULL, 0},
> +};
> +#endif
> +
> +int misc_init_r(void)
> +{
> +#ifdef CONFIG_CMD_BMODE
> + add_board_boot_modes(board_boot_modes);
> +#endif
> + return 0;
> +}
> diff --git a/configs/ot1200_defconfig b/configs/ot1200_defconfig
> new file mode 100644
> index 0000000..11797ce
> --- /dev/null
> +++ b/configs/ot1200_defconfig
> @@ -0,0 +1,3 @@
> +CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/imx/ddr/mx6q_4x_mt41j128.cfg,MX6Q"
> +CONFIG_ARM=y
> +CONFIG_TARGET_OT1200=y
> diff --git a/include/configs/ot1200.h b/include/configs/ot1200.h
> new file mode 100644
> index 0000000..8fb8177
> --- /dev/null
> +++ b/include/configs/ot1200.h
> @@ -0,0 +1,196 @@
> +/*
> + * Copyright (C) 2010-2013 Freescale Semiconductor, Inc.
> + * Copyright (C) 2014 Bachmann electronic GmbH
> + *
> + * SPDX-License-Identifier: GPL-2.0+
> + */
> +
> +#ifndef __CONFIG_H
> +#define __CONFIG_H
> +
> +#include "mx6_common.h"
> +#define CONFIG_MX6
> +#define CONFIG_DISPLAY_CPUINFO
> +#define CONFIG_DISPLAY_BOARDINFO
> +
> +#include <asm/arch/imx-regs.h>
> +#include <asm/imx-common/gpio.h>
> +
> +#define CONFIG_CMDLINE_TAG
> +#define CONFIG_SETUP_MEMORY_TAGS
> +#define CONFIG_INITRD_TAG
> +#define CONFIG_REVISION_TAG
> +#define CONFIG_SYS_GENERIC_BOARD
> +
> +/* Size of malloc() pool */
> +#define CONFIG_SYS_MALLOC_LEN (10 * 1024 * 1024)
> +
> +#define CONFIG_BOARD_EARLY_INIT_F
> +#define CONFIG_MISC_INIT_R
> +#define CONFIG_MXC_GPIO
> +
> +/* FUSE Configs */
> +#define CONFIG_CMD_FUSE
> +#define CONFIG_MXC_OCOTP
> +
> +/* UART Configs */
> +#define CONFIG_MXC_UART
> +#define CONFIG_MXC_UART_BASE UART1_BASE
> +
> +/* SF Configs */
> +#define CONFIG_CMD_SF
> +#define CONFIG_SPI
> +#define CONFIG_SPI_FLASH
> +#define CONFIG_SPI_FLASH_STMICRO
> +#define CONFIG_SPI_FLASH_WINBOND
> +#define CONFIG_SPI_FLASH_MACRONIX
> +#define CONFIG_SPI_FLASH_SST
> +#define CONFIG_MXC_SPI
> +#define CONFIG_SF_DEFAULT_BUS 2
> +#define CONFIG_SF_DEFAULT_CS (0|(IMX_GPIO_NR(1, 3)<<8))
> +#define CONFIG_SF_DEFAULT_SPEED 25000000
> +#define CONFIG_SF_DEFAULT_MODE (SPI_MODE_0)
> +
> +/* IO expander */
> +#define CONFIG_PCA953X
> +#define CONFIG_SYS_I2C_PCA953X_ADDR 0x20
> +#define CONFIG_SYS_I2C_PCA953X_WIDTH { {0x20, 16} }
> +#define CONFIG_CMD_PCA953X
> +#define CONFIG_CMD_PCA953X_INFO
> +
> +/* I2C Configs */
> +#define CONFIG_CMD_I2C
> +#define CONFIG_SYS_I2C
> +#define CONFIG_SYS_I2C_MXC
> +#define CONFIG_SYS_I2C_SPEED 100000
> +
> +/* OCOTP Configs */
> +#define CONFIG_CMD_IMXOTP
> +#define CONFIG_IMX_OTP
> +#define IMX_OTP_BASE OCOTP_BASE_ADDR
> +#define IMX_OTP_ADDR_MAX 0x7F
> +#define IMX_OTP_DATA_ERROR_VAL 0xBADABADA
> +#define IMX_OTPWRITE_ENABLED
> +
> +/* MMC Configs */
> +#define CONFIG_FSL_ESDHC
> +#define CONFIG_FSL_USDHC
> +#define CONFIG_SYS_FSL_ESDHC_ADDR 0
> +#define CONFIG_SYS_FSL_USDHC_NUM 2
> +
> +#define CONFIG_MMC
> +#define CONFIG_CMD_MMC
> +#define CONFIG_GENERIC_MMC
> +#define CONFIG_BOUNCE_BUFFER
> +
> +#ifdef CONFIG_MX6Q
> +#define CONFIG_CMD_SATA
> +#endif
> +
> +/*
> + * SATA Configs
> + */
> +#ifdef CONFIG_CMD_SATA
> +#define CONFIG_DWC_AHSATA
> +#define CONFIG_SYS_SATA_MAX_DEVICE 1
> +#define CONFIG_DWC_AHSATA_PORT_ID 0
> +#define CONFIG_DWC_AHSATA_BASE_ADDR SATA_ARB_BASE_ADDR
> +#define CONFIG_LBA48
> +#define CONFIG_LIBATA
> +#endif
> +
> +
> +#define CONFIG_CMD_PING
> +#define CONFIG_CMD_DHCP
> +#define CONFIG_CMD_MII
> +#define CONFIG_CMD_NET
> +#define CONFIG_FEC_MXC
> +#define CONFIG_MII
> +#define IMX_FEC_BASE ENET_BASE_ADDR
> +#define CONFIG_FEC_XCV_TYPE MII100
> +#define CONFIG_ETHPRIME "FEC"
> +#define CONFIG_FEC_MXC_PHYADDR 0x5
> +#define CONFIG_PHYLIB
> +#define CONFIG_PHY_SMSC
> +
> +/* Miscellaneous commands */
> +#define CONFIG_CMD_BMODE
> +#define CONFIG_CMD_SETEXPR
> +
> +/* allow to overwrite serial and ethaddr */
> +#define CONFIG_ENV_OVERWRITE
> +#define CONFIG_CONS_INDEX 1
> +#define CONFIG_BAUDRATE 115200
> +
> +/* Command definition */
> +#include <config_cmd_default.h>
> +
> +#undef CONFIG_CMD_IMLS
> +
> +#define CONFIG_BOOTDELAY 2
> +
> +#define CONFIG_PREBOOT ""
> +
> +#define CONFIG_LOADADDR 0x12000000
> +#define CONFIG_SYS_TEXT_BASE 0x17800000
> +
> +/* Miscellaneous configurable options */
> +#define CONFIG_SYS_LONGHELP
> +#define CONFIG_SYS_HUSH_PARSER
> +#define CONFIG_SYS_CBSIZE 1024
> +
> +/* Print Buffer Size */
> +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) +
> 16)
> +#define CONFIG_SYS_MAXARGS 16
> +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
> +
> +#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
> +
> +#define CONFIG_CMDLINE_EDITING
> +
> +/* Physical Memory Map */
> +#define CONFIG_NR_DRAM_BANKS 1
> +#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
> +#define PHYS_SDRAM_SIZE (1u * 1024 * 1024 * 1024)
> +
> +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
> +#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
> +#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
> +
> +#define CONFIG_SYS_INIT_SP_OFFSET \
> + (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
> +#define CONFIG_SYS_INIT_SP_ADDR \
> + (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
> +
> +/* FLASH and environment organization */
> +#define CONFIG_SYS_NO_FLASH
> +
> +#define CONFIG_ENV_IS_IN_SPI_FLASH
> +#define CONFIG_ENV_SIZE (64 * 1024) /* 64 kb */
> +#define CONFIG_ENV_OFFSET (1024 * 1024)
> +#define CONFIG_ENV_SECT_SIZE (64 * 1024) /* M25P16 has an erase
> size of 64 KiB */
> +#define CONFIG_ENV_SPI_BUS CONFIG_SF_DEFAULT_BUS
> +#define CONFIG_ENV_SPI_CS CONFIG_SF_DEFAULT_CS
> +#define CONFIG_ENV_SPI_MODE CONFIG_SF_DEFAULT_MODE
> +#define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED
> +
> +#define CONFIG_OF_LIBFDT
> +#define CONFIG_CMD_BOOTZ
> +
> +#ifndef CONFIG_SYS_DCACHE_OFF
> +#define CONFIG_CMD_CACHE
> +#endif
> +
> +#define CONFIG_CMD_BOOTZ
> +#define CONFIG_SUPPORT_RAW_INITRD
> +
> +/* FS Configs */
> +#define CONFIG_CMD_EXT3
> +#define CONFIG_CMD_EXT4
> +#define CONFIG_DOS_PARTITION
> +#define CONFIG_CMD_FS_GENERIC
> +
> +#define CONFIG_BOOTP_SERVERIP
> +#define CONFIG_BOOTP_BOOTFILE
> +
> +#endif /* __CONFIG_H */
>
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sba...@denx.de
=====================================================================
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
