On 08/10/14 20:12, Nikita Kiryanov wrote:
> Add USB and USB OTG host support for Compulab CM-FX6 CoM.
>
> Cc: Igor Grinberg <grinb...@compulab.co.il>
> Cc: Stefano Babic <sba...@denx.de>
> Cc: Tom Rini <tr...@ti.com>
> Signed-off-by: Nikita Kiryanov <nik...@compulab.co.il>
> ---
> Changes in V2:
> - No changes
>
> board/compulab/cm_fx6/cm_fx6.c | 75
> ++++++++++++++++++++++++++++++++++++++++++
> board/compulab/cm_fx6/common.h | 3 ++
> include/configs/cm_fx6.h | 10 ++++++
> 3 files changed, 88 insertions(+)
>
> diff --git a/board/compulab/cm_fx6/cm_fx6.c b/board/compulab/cm_fx6/cm_fx6.c
> index e993de2..28c54b4 100644
> --- a/board/compulab/cm_fx6/cm_fx6.c
> +++ b/board/compulab/cm_fx6/cm_fx6.c
[...]
> +static int cm_fx6_usb_hub_reset(void)
> +{
> + int err;
> +
> + err = gpio_request(CM_FX6_USB_HUB_RST, "usb hub rst");
> + if (err) {
> + printf("USB hub rst gpio request failed: %d\n", err);
> + return -1;
> + }
> +
> + SETUP_IOMUX_PAD(PAD_SD3_RST__GPIO7_IO08 | MUX_PAD_CTRL(NO_PAD_CTRL));
> + gpio_direction_output(CM_FX6_USB_HUB_RST, 0);
> + udelay(10);
> + gpio_direction_output(CM_FX6_USB_HUB_RST, 1);
> + mdelay(1);
> +
> + return 0;
> +}
> +
> +static void cm_fx6_init_usb_otg(void)
Can this function also return int as the one above?
> +{
> + int ret;
> + struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
> +
> + ret = gpio_request(SB_FX6_USB_OTG_PWR, "usb-pwr");
> + if (ret)
> + printf("USB OTG pwr gpio request failed: %d\n", ret);
> +
> + SETUP_IOMUX_PAD(PAD_EIM_D22__GPIO3_IO22 | MUX_PAD_CTRL(NO_PAD_CTRL));
> + SETUP_IOMUX_PAD(PAD_ENET_RX_ER__USB_OTG_ID |
> + MUX_PAD_CTRL(WEAK_PULLDOWN));
> + clrbits_le32(&iomux->gpr[1], IOMUXC_GPR1_OTG_ID_MASK);
> + /* disable ext. charger detect, or it'll affect signal quality at dp. */
> + gpio_direction_output(SB_FX6_USB_OTG_PWR, 0);
> +}
> +
> +#define MX6_USBNC_BASEADDR 0x2184800
> +#define USBNC_USB_H1_PWR_POL (1 << 9)
> +int board_ehci_hcd_init(int port)
> +{
> + u32 *usbnc_usb_uh1_ctrl = (u32 *)(MX6_USBNC_BASEADDR + 4);
> + u32 val;
> +
> + switch (port) {
> + case 0:
> + cm_fx6_init_usb_otg();
> + break;
> + case 1:
> + SETUP_IOMUX_PAD(PAD_GPIO_0__USB_H1_PWR |
> + MUX_PAD_CTRL(NO_PAD_CTRL));
> +
> + /* Set PWR polarity to match power switch's enable polarity */
> + val = __raw_readl(usbnc_usb_uh1_ctrl);
> + val |= USBNC_USB_H1_PWR_POL;
> + __raw_writel(val, usbnc_usb_uh1_ctrl);
Can we have setbits_le32() here?
> + return cm_fx6_usb_hub_reset();
> + default:
> + break;
> + }
> +
> + return 0;
> +}
> +
> +int board_ehci_power(int port, int on)
> +{
> + return port ? 0 : gpio_direction_output(SB_FX6_USB_OTG_PWR, on);
Here port is a port number, not some bool conditional.
Please be explicit about it and don't use the construct above for such cases.
[...]
--
Regards,
Igor.
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
