On 07/04/2014 05:08 PM, Przemyslaw Marczak wrote:
> On 07/04/2014 08:07 AM, Jaehoon Chung wrote:
>> On 07/02/2014 08:50 PM, Przemyslaw Marczak wrote:
>>> This board file supports standard features of Odroid X2 and U3 boards:
>>> - Exynos4412 core clock set to 1000MHz and MPLL peripherial clock set to
>>> 800MHz,
>>> - MAX77686 power regulator,
>>> - USB PHY,
>>> - enable XCL205 - power for board peripherials
>>> - check board type: U3 or X2.
>>> - enable Odroid U3 FAN cooler
>>>
>>> Signed-off-by: Przemyslaw Marczak <p.marc...@samsung.com>
>>> Cc: Minkyu Kang <mk7.k...@samsung.com>
>>> Cc: Tom Rini <tr...@ti.com>
>>>
>>> ---
>>> Changes v2:
>>> - enable fan on odroid U3
>>>
>>> Changes v3:
>>> - odroid.c: clean up board name related code
>>> - odroid.c: remove static from set_board_type()
>>> - odroid.c: add implementation of functions: get_dfu_alt_*
>>> - odroid.c: include misc.h
>>>
>>> Changes v4:
>>> odroid.c: dfu_get_alt_boot: add call get_boot_mode()
>>> ---
>>> board/samsung/odroid/Makefile | 8 +
>>> board/samsung/odroid/odroid.c | 466
>>> ++++++++++++++++++++++++++++++++++++++++++
>>> board/samsung/odroid/setup.h | 227 ++++++++++++++++++++
>>> 3 files changed, 701 insertions(+)
>>> create mode 100644 board/samsung/odroid/Makefile
>>> create mode 100644 board/samsung/odroid/odroid.c
>>> create mode 100644 board/samsung/odroid/setup.h
>>>
>>> diff --git a/board/samsung/odroid/Makefile b/board/samsung/odroid/Makefile
>>> new file mode 100644
>>> index 0000000..b98aaeb
>>> --- /dev/null
>>> +++ b/board/samsung/odroid/Makefile
>>> @@ -0,0 +1,8 @@
>>> +#
>>> +# Copyright (c) 2014 Samsung Electronics Co., Ltd. All rights reserved.
>>> +# Przemyslaw Marczak <p.marc...@samsung.com>
>>> +#
>>> +# SPDX-License-Identifier: GPL-2.0+
>>> +#
>>> +
>>> +obj-y := odroid.o
>>> diff --git a/board/samsung/odroid/odroid.c b/board/samsung/odroid/odroid.c
>>> new file mode 100644
>>> index 0000000..28706af
>>> --- /dev/null
>>> +++ b/board/samsung/odroid/odroid.c
>>> @@ -0,0 +1,466 @@
>>> +/*
>>> + * Copyright (C) 2014 Samsung Electronics
>>> + * Przemyslaw Marczak <p.marc...@samsung.com>
>>> + *
>>> + * SPDX-License-Identifier: GPL-2.0+
>>> + */
>>> +
>>> +#include <common.h>
>>> +#include <asm/arch/pinmux.h>
>>> +#include <asm/arch/power.h>
>>> +#include <asm/arch/clock.h>
>>> +#include <asm/arch/gpio.h>
>>> +#include <asm/gpio.h>
>>> +#include <asm/arch/cpu.h>
>>> +#include <power/pmic.h>
>>> +#include <power/max77686_pmic.h>
>>> +#include <errno.h>
>>> +#include <usb.h>
>>> +#include <usb/s3c_udc.h>
>>> +#include <samsung/misc.h>
>>> +#include "setup.h"
>>> +
>>> +DECLARE_GLOBAL_DATA_PTR;
>>> +
>>> +#ifdef CONFIG_BOARD_TYPES
>>> +/* Odroid board types */
>>> +enum {
>>> + ODROID_TYPE_U3,
>>> + ODROID_TYPE_X2,
>>> +};
>>> +
>>> +void set_board_type(void)
>>> +{
>>> + int val;
>>> +
>>> + /* Check GPC1 pin 2 */
>>> + gpio_set_pull(EXYNOS4X12_GPIO_C12, S5P_GPIO_PULL_NONE);
>>> + gpio_set_drv(EXYNOS4X12_GPIO_C12, S5P_GPIO_DRV_4X);
>>> + gpio_direction_input(EXYNOS4X12_GPIO_C12);
>>> +
>>> + /* XCL205 - needs some latch time */
>>> + mdelay(10);
>>> +
>>> + /* Check GPC1 pin2 - LED supplied by XCL205 - X2 only */
>>> + val = gpio_get_value(EXYNOS4X12_GPIO_C12);
>>> + if (val)
>> val is unnecessary. "int val" can be removed.
>> if (gpio_get_value(EXYNS4x12_GPIO_C12))
>> ....
>>
> ok
>>> + gd->board_type = ODROID_TYPE_X2;
>>> + else
>>> + gd->board_type = ODROID_TYPE_U3;
>>> +}
>>> +
>>> +const char *get_board_name(void)
>>> +{
>>> + const char *board_name = "odroid";
>> Is there other approach or general method for getting board name?
>>
> Actually, the board name is the same as CONFIG_SYS_BOARD, but we are going to
> have only one binary for Exynos 4 boards in the future - so such function is
> welcome. We can also put this into the dts file.
In future...Then using dt-file would be better than this. :)
Best Regards,
Jaehoon Chung
>
>>> +
>>> + return board_name;
>>> +}
>>> +
>>> +const char *get_board_type(void)
>>> +{
>>> + const char *board_type[] = {"u3", "x2"};
>>> +
>>> + return board_type[gd->board_type];
>>> +}
>>> +#endif
>>> +
>>> +#ifdef CONFIG_SET_DFU_ALT_INFO
>>> +char *get_dfu_alt_system(void)
>>> +{
>>> + return getenv("dfu_alt_system");
>>> +}
>>> +
>>> +char *get_dfu_alt_boot(void)
>>> +{
>>> + char *alt_boot = NULL;
>>> +
>>> + switch (get_boot_mode()) {
>>> + case BOOT_MODE_MMC:
>>> + alt_boot = CONFIG_DFU_ALT_BOOT_SD;
>>> + break;
>>> + default:
>>> + alt_boot = CONFIG_DFU_ALT_BOOT_EMMC;
>>> + break;
>>> + }
>>> +
>>> + if (!alt_boot)
>>> + return NULL;
>>
>> Is it need? alt_boot is set to CONFIG_DFU_ALT_BOOT_EMMC by default, isn't?
>> CONFIG_DFU_ALT_BOOT_EMMC is 0?
>>
> Oops, right. I must fix that.
>>> +
>>> + setenv("dfu_alt_boot", alt_boot);
>>> +
>>> + return alt_boot;
>>> +}
>>> +#endif
>>> +
>>> +static void board_clock_init(void)
>>> +{
>>> + unsigned int set, clr, clr_src_cpu, clr_pll_con0, clr_src_dmc;
>>> + struct exynos4x12_clock *clk = (struct exynos4x12_clock *)
>>> + samsung_get_base_clock();
>>> +
>>> + /*
>>> + * CMU_CPU clocks src to MPLL
>>> + * Bit values: 0 ; 1
>>> + * MUX_APLL_SEL: FIN_PLL ; FOUT_APLL
>>> + * MUX_CORE_SEL: MOUT_APLL ; SCLK_MPLL
>>> + * MUX_HPM_SEL: MOUT_APLL ; SCLK_MPLL_USER_C
>>> + * MUX_MPLL_USER_SEL_C: FIN_PLL ; SCLK_MPLL
>>> + */
>>> + clr_src_cpu = MUX_APLL_SEL(0x1) | MUX_CORE_SEL(0x1) |
>>> + MUX_HPM_SEL(0x1) | MUX_MPLL_USER_SEL_C(0x1);
>>> + set = MUX_APLL_SEL(0) | MUX_CORE_SEL(1) | MUX_HPM_SEL(1) |
>>> + MUX_MPLL_USER_SEL_C(1);
>> 0x1 or 1? you can use it consistency. MUX_APLL_SEL(1) or MUX_APLL_SEL(0x1).
>>
> ok, will be fixed.
>>> +
>>> + clrsetbits_le32(&clk->src_cpu, clr_src_cpu, set);
>>> +
>>> + /* Wait for mux change */
>>> + while (readl(&clk->mux_stat_cpu) & MUX_STAT_CPU_CHANGING)
>>> + continue;
>>> +
>>> + /* Set APLL to 1000MHz */
>>> + clr_pll_con0 = SDIV(0x7) | PDIV(0x3f) | MDIV(0x3ff) | FSEL(0x1);
>>> + set = SDIV(0) | PDIV(3) | MDIV(125) | FSEL(1);
>>> +
>>> + clrsetbits_le32(&clk->apll_con0, clr_pll_con0, set);
>>> +
>>> + /* Wait for PLL to be locked */
>>> + while (!(readl(&clk->apll_con0) & PLL_LOCKED_BIT))
>>> + continue;
>>> +
>>> + /* Set CMU_CPU clocks src to APLL */
>>> + set = MUX_APLL_SEL(1) | MUX_CORE_SEL(0) | MUX_HPM_SEL(0) |
>>> + MUX_MPLL_USER_SEL_C(1);
>>> + clrsetbits_le32(&clk->src_cpu, clr_src_cpu, set);
>>> +
>>> + /* Wait for mux change */
>>> + while (readl(&clk->mux_stat_cpu) & MUX_STAT_CPU_CHANGING)
>>> + continue;
>>> +
>>> + set = CORE_RATIO(0) | COREM0_RATIO(2) | COREM1_RATIO(5) |
>>> + PERIPH_RATIO(0) | ATB_RATIO(4) | PCLK_DBG_RATIO(1) |
>>> + APLL_RATIO(0) | CORE2_RATIO(0);
>>> + /*
>>> + * Set dividers for MOUTcore = 1000 MHz
>>> + * coreout = MOUT / (ratio + 1) = 1000 MHz (0)
>>> + * corem0 = armclk / (ratio + 1) = 333 MHz (2)
>>> + * corem1 = armclk / (ratio + 1) = 166 MHz (5)
>>> + * periph = armclk / (ratio + 1) = 1000 MHz (0)
>>> + * atbout = MOUT / (ratio + 1) = 200 MHz (4)
>>> + * pclkdbgout = atbout / (ratio + 1) = 100 MHz (1)
>>> + * sclkapll = MOUTapll / (ratio + 1) = 1000 MHz (0)
>>> + * core2out = core_out / (ratio + 1) = 1000 MHz (0) (armclk)
>>> + */
>>> + clr = CORE_RATIO(0x7) | COREM0_RATIO(0x7) | COREM1_RATIO(0x7) |
>>> + PERIPH_RATIO(0x7) | ATB_RATIO(0x7) | PCLK_DBG_RATIO(0x7) |
>>> + APLL_RATIO(0x7) | CORE2_RATIO(0x7);
>>> +
>>> + clrsetbits_le32(&clk->div_cpu0, clr, set);
>>> +
>>> + /* Wait for divider ready status */
>>> + while (readl(&clk->div_stat_cpu0) & DIV_STAT_CPU0_CHANGING)
>>> + continue;
>>> +
>>> + /*
>>> + * For MOUThpm = 1000 MHz (MOUTapll)
>>> + * doutcopy = MOUThpm / (ratio + 1) = 200 (4)
>>> + * sclkhpm = doutcopy / (ratio + 1) = 200 (4)
>>> + * cores_out = armclk / (ratio + 1) = 1000 (0)
>>> + */
>>> + clr = COPY_RATIO(0x7) | HPM_RATIO(0x7) | CORES_RATIO(0x7);
>>> + set = COPY_RATIO(4) | HPM_RATIO(4) | CORES_RATIO(0);
>>> +
>>> + clrsetbits_le32(&clk->div_cpu1, clr, set);
>>> +
>>> + /* Wait for divider ready status */
>>> + while (readl(&clk->div_stat_cpu1) & DIV_STAT_CPU1_CHANGING)
>>> + continue;
>>> +
>>> + /*
>>> + * Set CMU_DMC clocks src to APLL
>>> + * Bit values: 0 ; 1
>>> + * MUX_C2C_SEL: SCLKMPLL ; SCLKAPLL
>>> + * MUX_DMC_BUS_SEL: SCLKMPLL ; SCLKAPLL
>>> + * MUX_DPHY_SEL: SCLKMPLL ; SCLKAPLL
>>> + * MUX_MPLL_SEL: FINPLL ; MOUT_MPLL_FOUT
>>> + * MUX_PWI_SEL: 0110 (MPLL); 0111 (EPLL); 1000 (VPLL); 0(XXTI)
>>> + * MUX_G2D_ACP0_SEL: SCLKMPLL ; SCLKAPLL
>>> + * MUX_G2D_ACP1_SEL: SCLKEPLL ; SCLKVPLL
>>> + * MUX_G2D_ACP_SEL: OUT_ACP0 ; OUT_ACP1
>>> + */
>>> + clr_src_dmc = MUX_C2C_SEL(0x1) | MUX_DMC_BUS_SEL(0x1) |
>>> + MUX_DPHY_SEL(0x1) | MUX_MPLL_SEL(0x1) |
>>> + MUX_PWI_SEL(0xf) | MUX_G2D_ACP0_SEL(0x1) |
>>> + MUX_G2D_ACP1_SEL(0x1) | MUX_G2D_ACP_SEL(0x1);
>>> + set = MUX_C2C_SEL(1) | MUX_DMC_BUS_SEL(1) | MUX_DPHY_SEL(1) |
>>> + MUX_MPLL_SEL(0) | MUX_PWI_SEL(0) | MUX_G2D_ACP0_SEL(1) |
>>> + MUX_G2D_ACP1_SEL(1) | MUX_G2D_ACP_SEL(1);
>>> +
>>> + clrsetbits_le32(&clk->src_dmc, clr_src_dmc, set);
>>> +
>>> + /* Wait for mux change */
>>> + while (readl(&clk->mux_stat_dmc) & MUX_STAT_DMC_CHANGING)
>>> + continue;
>>> +
>>> + /* Set MPLL to 800MHz */
>>> + set = SDIV(0) | PDIV(3) | MDIV(100) | FSEL(0) | PLL_ENABLE(1);
>>> +
>>> + clrsetbits_le32(&clk->mpll_con0, clr_pll_con0, set);
>>> +
>>> + /* Wait for PLL to be locked */
>>> + while (!(readl(&clk->mpll_con0) & PLL_LOCKED_BIT))
>>> + continue;
>>> +
>>> + /* Switch back CMU_DMC mux */
>>> + set = MUX_C2C_SEL(0) | MUX_DMC_BUS_SEL(0) | MUX_DPHY_SEL(0) |
>>> + MUX_MPLL_SEL(1) | MUX_PWI_SEL(8) | MUX_G2D_ACP0_SEL(0) |
>>> + MUX_G2D_ACP1_SEL(0) | MUX_G2D_ACP_SEL(0);
>>> +
>>> + clrsetbits_le32(&clk->src_dmc, clr_src_dmc, set);
>>> +
>>> + /* Wait for mux change */
>>> + while (readl(&clk->mux_stat_dmc) & MUX_STAT_DMC_CHANGING)
>>> + continue;
>>> +
>>> + /* CLK_DIV_DMC0 */
>>> + clr = ACP_RATIO(0x7) | ACP_PCLK_RATIO(0x7) | DPHY_RATIO(0x7) |
>>> + DMC_RATIO(0x7) | DMCD_RATIO(0x7) | DMCP_RATIO(0x7);
>>> + /*
>>> + * For:
>>> + * MOUTdmc = 800 MHz
>>> + * MOUTdphy = 800 MHz
>>> + *
>>> + * aclk_acp = MOUTdmc / (ratio + 1) = 200 (3)
>>> + * pclk_acp = aclk_acp / (ratio + 1) = 100 (1)
>>> + * sclk_dphy = MOUTdphy / (ratio + 1) = 400 (1)
>>> + * sclk_dmc = MOUTdmc / (ratio + 1) = 400 (1)
>>> + * aclk_dmcd = sclk_dmc / (ratio + 1) = 200 (1)
>>> + * aclk_dmcp = aclk_dmcd / (ratio + 1) = 100 (1)
>>> + */
>>> + set = ACP_RATIO(3) | ACP_PCLK_RATIO(1) | DPHY_RATIO(1) |
>>> + DMC_RATIO(1) | DMCD_RATIO(1) | DMCP_RATIO(1);
>>> +
>>> + clrsetbits_le32(&clk->div_dmc0, clr, set);
>>> +
>>> + /* Wait for divider ready status */
>>> + while (readl(&clk->div_stat_dmc0) & DIV_STAT_DMC0_CHANGING)
>>> + continue;
>>> +
>>> + /* CLK_DIV_DMC1 */
>>> + clr = G2D_ACP_RATIO(0xf) | C2C_RATIO(0x7) | PWI_RATIO(0xf) |
>>> + C2C_ACLK_RATIO(0x7) | DVSEM_RATIO(0x7f) | DPM_RATIO(0x7f);
>>> + /*
>>> + * For:
>>> + * MOUTg2d = 800 MHz
>>> + * MOUTc2c = 800 Mhz
>>> + * MOUTpwi = 108 MHz
>>> + *
>>> + * sclk_g2d_acp = MOUTg2d / (ratio + 1) = 400 (1)
>>> + * sclk_c2c = MOUTc2c / (ratio + 1) = 400 (1)
>>> + * aclk_c2c = sclk_c2c / (ratio + 1) = 200 (1)
>>> + * sclk_pwi = MOUTpwi / (ratio + 1) = 18 (5)
>>> + */
>>> + set = G2D_ACP_RATIO(1) | C2C_RATIO(1) | PWI_RATIO(5) |
>>> + C2C_ACLK_RATIO(1) | DVSEM_RATIO(1) | DPM_RATIO(1);
>>> +
>>> + clrsetbits_le32(&clk->div_dmc1, clr, set);
>>> +
>>> + /* Wait for divider ready status */
>>> + while (readl(&clk->div_stat_dmc1) & DIV_STAT_DMC1_CHANGING)
>>> + continue;
>>> +
>>> + /* CLK_SRC_PERIL0 */
>>> + clr = UART0_SEL(0xf) | UART1_SEL(0xf) | UART2_SEL(0xf) |
>>> + UART3_SEL(0xf) | UART4_SEL(0xf);
>>> + /*
>>> + * Set CLK_SRC_PERIL0 clocks src to MPLL
>>> + * src values: 0(XXTI); 1(XusbXTI); 2(SCLK_HDMI24M); 3(SCLK_USBPHY0);
>>> + * 5(SCLK_HDMIPHY); 6(SCLK_MPLL_USER_T); 7(SCLK_EPLL);
>>> + * 8(SCLK_VPLL)
>>> + *
>>> + * Set all to SCLK_MPLL_USER_T
>>> + */
>>> + set = UART0_SEL(6) | UART1_SEL(6) | UART2_SEL(6) | UART3_SEL(6) |
>>> + UART4_SEL(6);
>>> +
>>> + clrsetbits_le32(&clk->src_peril0, clr, set);
>>> +
>>> + /* CLK_DIV_PERIL0 */
>>> + clr = UART0_RATIO(0xf) | UART1_RATIO(0xf) | UART2_RATIO(0xf) |
>>> + UART3_RATIO(0xf) | UART4_RATIO(0xf);
>>> + /*
>>> + * For MOUTuart0-4: 800MHz
>>> + *
>>> + * SCLK_UARTx = MOUTuartX / (ratio + 1) = 100 (7)
>>> + */
>>> + set = UART0_RATIO(7) | UART1_RATIO(7) | UART2_RATIO(7) |
>>> + UART3_RATIO(7) | UART4_RATIO(7);
>>> +
>>> + clrsetbits_le32(&clk->div_peril0, clr, set);
>>> +
>>> + while (readl(&clk->div_stat_peril0) & DIV_STAT_PERIL0_CHANGING)
>>> + continue;
>>> +
>>> + /* CLK_DIV_FSYS1 */
>>> + clr = MMC0_RATIO(0xf) | MMC0_PRE_RATIO(0xff) | MMC1_RATIO(0xf) |
>>> + MMC1_PRE_RATIO(0xff);
>>> + /*
>>> + * For MOUTmmc0-3 = 800 MHz (MPLL)
>>> + *
>>> + * DOUTmmc1 = MOUTmmc1 / (ratio + 1) = 100 (7)
>>> + * sclk_mmc1 = DOUTmmc1 / (ratio + 1) = 50 (1)
>>> + * DOUTmmc0 = MOUTmmc0 / (ratio + 1) = 100 (7)
>>> + * sclk_mmc0 = DOUTmmc0 / (ratio + 1) = 50 (1)
>>> + */
>>> + set = MMC0_RATIO(7) | MMC0_PRE_RATIO(1) | MMC1_RATIO(7) |
>>> + MMC1_PRE_RATIO(1);
>>> +
>>> + clrsetbits_le32(&clk->div_fsys1, clr, set);
>>> +
>>> + /* Wait for divider ready status */
>>> + while (readl(&clk->div_stat_fsys1) & DIV_STAT_FSYS1_CHANGING)
>>> + continue;
>>> +
>>> + /* CLK_DIV_FSYS2 */
>>> + clr = MMC2_RATIO(0xf) | MMC2_PRE_RATIO(0xff) | MMC3_RATIO(0xf) |
>>> + MMC3_PRE_RATIO(0xff);
>>> + /*
>>> + * For MOUTmmc0-3 = 800 MHz (MPLL)
>>> + *
>>> + * DOUTmmc3 = MOUTmmc3 / (ratio + 1) = 100 (7)
>>> + * sclk_mmc3 = DOUTmmc3 / (ratio + 1) = 50 (1)
>>> + * DOUTmmc2 = MOUTmmc2 / (ratio + 1) = 100 (7)
>>> + * sclk_mmc2 = DOUTmmc2 / (ratio + 1) = 50 (1)
>>> + */
>>> + set = MMC2_RATIO(7) | MMC2_PRE_RATIO(1) | MMC3_RATIO(7) |
>>> + MMC3_PRE_RATIO(1);
>>> +
>>> + clrsetbits_le32(&clk->div_fsys2, clr, set);
>>> +
>>> + /* Wait for divider ready status */
>>> + while (readl(&clk->div_stat_fsys2) & DIV_STAT_FSYS2_CHANGING)
>>> + continue;
>>> +
>>> + /* CLK_DIV_FSYS3 */
>>> + clr = MMC4_RATIO(0xf) | MMC4_PRE_RATIO(0xff);
>>> + /*
>>> + * For MOUTmmc4 = 800 MHz (MPLL)
>>> + *
>>> + * DOUTmmc4 = MOUTmmc4 / (ratio + 1) = 100 (7)
>>> + * sclk_mmc4 = DOUTmmc4 / (ratio + 1) = 100 (0)
>>> + */
>>> + set = MMC4_RATIO(7) | MMC4_PRE_RATIO(0);
>>> +
>>> + clrsetbits_le32(&clk->div_fsys3, clr, set);
>>> +
>>> + /* Wait for divider ready status */
>>> + while (readl(&clk->div_stat_fsys3) & DIV_STAT_FSYS3_CHANGING)
>>> + continue;
>>> +
>>> + return;
>>> +}
>>> +
>>> +static void board_gpio_init(void)
>>> +{
>>> + /* Set GPA1 pin 1 to HI - enable XCL205 output */
>>> + gpio_set_pull(EXYNOS4X12_GPIO_A11, S5P_GPIO_PULL_UP);
>>> + gpio_set_drv(EXYNOS4X12_GPIO_A11, S5P_GPIO_DRV_4X);
>>> + gpio_direction_output(EXYNOS4X12_GPIO_A11, 1);
>>> +
>>> + gpio_cfg_pin(EXYNOS4X12_GPIO_K12, S5P_GPIO_FUNC(0x1));
>>> + gpio_set_pull(EXYNOS4X12_GPIO_K12, S5P_GPIO_PULL_NONE);
>>> + gpio_set_drv(EXYNOS4X12_GPIO_K12, S5P_GPIO_DRV_4X);
>>> +
>>> + /* Enable FAN (Odroid U3) */
>>> + gpio_set_pull(EXYNOS4X12_GPIO_D00, S5P_GPIO_PULL_UP);
>>> + gpio_set_drv(EXYNOS4X12_GPIO_D00, S5P_GPIO_DRV_4X);
>>> + gpio_direction_output(EXYNOS4X12_GPIO_D00, 1);
>>> +}
>>> +
>>> +static int pmic_init_max77686(void)
>>> +{
>>> + struct pmic *p = pmic_get("MAX77686_PMIC");
>>> +
>>> + if (pmic_probe(p))
>>> + return -ENODEV;
>>> +
>>> + /* Set LDO Voltage */
>>> + max77686_set_ldo_voltage(p, 20, 1800000); /* LDO20 eMMC */
>>> + max77686_set_ldo_voltage(p, 21, 2800000); /* LDO21 SD */
>>> + max77686_set_ldo_voltage(p, 22, 2800000); /* LDO22 eMMC */
>>
>> LDO20/22 are used the eMMC? VDD/VDD-IO power?
>>
>
> Yes, those are the pull-up voltage sources for eMMC and SD.
>
>
> Thank you,
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
