From: Jamie Lentin <j...@lentin.co.uk> Extend dnskw to support the D-Link DNS-320 ShareCenter NAS also. For more information on this NAS, see:-
http://jamie.lentin.co.uk/devices/dlink-dns320 http://dns323.kood.org/dns-320 http://sharecenter.dlink.com/products/DNS-320 Changes since V1: * Shorten CONFIG_IDENT_STRING [Prafulla Wadaskar] Changes since V2: * Correct a mismerge conflict Signed-off-by: Jamie Lentin <j...@lentin.co.uk> Cc: prafu...@marvell.com Cc: albert.u.b...@aribaud.net Cc: ste...@herbrechtsmeier.net --- board/d-link/dnskw/dnskw.c | 8 +- board/d-link/dnskw/dnskw.h | 6 + board/d-link/dnskw/kwbimage.dns320.cfg | 207 +++++++++++++++++++++++++++++++++ boards.cfg | 1 + include/configs/dnskw.h | 10 ++ 5 files changed, 228 insertions(+), 4 deletions(-) create mode 100644 board/d-link/dnskw/kwbimage.dns320.cfg diff --git a/board/d-link/dnskw/dnskw.c b/board/d-link/dnskw/dnskw.c index 22b0ffb..a9fa9a2 100644 --- a/board/d-link/dnskw/dnskw.c +++ b/board/d-link/dnskw/dnskw.c @@ -42,8 +42,8 @@ int board_early_init_f(void) MPP10_UART0_TXD, MPP11_UART0_RXD, MPP12_SD_CLK, - MPP13_SD_CMD, - MPP14_SD_D0, + MPP13_UART1_TXD, /* Custom ...*/ + MPP14_UART1_RXD, /* ... controller */ MPP15_SD_D1, MPP16_SD_D2, MPP17_SD_D3, @@ -58,13 +58,13 @@ int board_early_init_f(void) MPP26_GPIO, /* power led */ MPP27_GPIO, /* sata0(right) error led */ MPP28_GPIO, /* sata1(left) error led */ - MPP29_GPIO, /* usb error led */ + MPP29_GPIO, /* usb error led (dns-325) */ MPP30_GPIO, MPP31_GPIO, MPP32_GPIO, MPP33_GPIO, MPP34_GPIO, /* power key */ - MPP35_GPIO, + MPP35_GPIO, /* usb error led (dns-320) */ MPP36_GPIO, MPP37_GPIO, MPP38_GPIO, diff --git a/board/d-link/dnskw/dnskw.h b/board/d-link/dnskw/dnskw.h index 8d2e2b1..f87f02c 100644 --- a/board/d-link/dnskw/dnskw.h +++ b/board/d-link/dnskw/dnskw.h @@ -27,6 +27,12 @@ #define DNSKW_OE_VAL_HIGH 0x00000800 /* disable leds */ #endif /* CONFIG_BOARD_IS_DNS325 */ +/* DNS-320 specific configuration */ +#ifdef CONFIG_BOARD_IS_DNS320 +#define DNSKW_OE_VAL_LOW 0x38000000 /* disable leds */ +#define DNSKW_OE_VAL_HIGH 0x00000808 /* disable leds */ +#endif /* CONFIG_BOARD_IS_DNS320 */ + /* PHY related */ #define MV88E1116_MAC_CTRL_REG 21 #define MV88E1116_PGADR_REG 22 diff --git a/board/d-link/dnskw/kwbimage.dns320.cfg b/board/d-link/dnskw/kwbimage.dns320.cfg new file mode 100644 index 0000000..b515bf2 --- /dev/null +++ b/board/d-link/dnskw/kwbimage.dns320.cfg @@ -0,0 +1,207 @@ +# +# Copyright (C) 2012 +# Jamie Lentin <j...@lentin.co.uk> +# +# Based on dns325 support: +# Copyright (C) 2011 +# Stefan Herbrechtsmeier <ste...@code.herbrechtsmeier.net> +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, +# MA 02110-1301 USA +# +# Refer docs/README.kwimage for more details about how-to configure +# and create kirkwood boot image +# + +# Boot Media configurations +BOOT_FROM nand +NAND_ECC_MODE default +NAND_PAGE_SIZE 0x0800 + +# SOC registers configuration using bootrom header extension +# Maximum KWBIMAGE_MAX_CONFIG configurations allowed + +# Configure RGMII-0 interface pad voltage to 1.8V +DATA 0xFFD100e0 0x1b1b1b9b + +#Dram initalization for SINGLE x16 CL=3 @ 200MHz +DATA 0xFFD01400 0x43000618 # DDR Configuration register +# bit13-0: 0x618 DDR2 clks refresh rate +# bit23-14: 0 required +# bit24: 1, enable exit self refresh mode on DDR access +# bit25: 1 required +# bit29-26: 0 required +# bit31-30: 0b01 required + +DATA 0xFFD01404 0x35143000 # DDR Controller Control Low +# bit3-0: 0 required +# bit4: 0, addr/cmd in smame cycle +# bit5: 0, clk is driven during self refresh, we don't care for APX +# bit6: 0, use recommended falling edge of clk for addr/cmd +# bit11-7: 0 required +# bit12: 1 required +# bit13: 1 required +# bit14: 0, input buffer always powered up +# bit17-15: 0 required +# bit18: 1, cpu lock transaction enabled +# bit19: 0 required +# bit23-20: 1, Recommended for CL 3 and STARTBURST_DEL disabled +# bit27-24: 5, CL + 2 +# bit30-28: 3 required +# bit31: 0, no additional STARTBURST delay + +DATA 0xFFD01408 0x11012227 # DDR Timing (Low) +# bit3-0: 7, 8 cycle tRAS (tRAS[3-0]) +# bit7-4: 2, 3 cycle tRCD +# bit11-8: 2, 3 cycle tRP +# bit15-12: 2, 3 cycle tWR +# bit19-16: 1, 2 cycle tWTR +# bit20: 1, 2 cycle tRAS (tRAS[4]) +# bit23-21: 0 required +# bit27-24: 1, 2 cycle tRRD +# bit31-28: 1, 2 cycle tRTP + +DATA 0xFFD0140C 0x00000819 # DDR Timing (High) +# bit6-0: 0x19, 20 cycle tRFC +# bit8-7: 0, 1 cycle tR2bR +# bit10-9: 0, 1 cycle tR2W +# bit12-11: 1, 1 cycle tW2W gap +# bit31-13: 0 required + +DATA 0xFFD01410 0x00000008 # DDR Address Control +# bit1-0: 0, Cs0width=x8 (out of spec?) +# bit3-2: 2, Cs0size=512Mb +# bit5-4: 0, Cs1width=nonexistent +# bit7-6: 0, Cs1size=nonexistent +# bit9-8: 0, Cs2width=nonexistent +# bit11-10: 0, Cs2size=nonexistent +# bit13-12: 0, Cs3width=nonexistent +# bit15-14: 0, Cs3size=nonexistent +# bit16: 0, Cs0AddrSel +# bit17: 0, Cs1AddrSel +# bit18: 0, Cs2AddrSel +# bit19: 0, Cs3AddrSel +# bit31-20: 0 required + +DATA 0xFFD01414 0x00000000 # DDR Open Pages Control +# bit0: 0, OPEn=OpenPage enabled +# bit31-1: 0 required + +DATA 0xFFD01418 0x00000000 # DDR Operation +# bit3-0: 0, Cmd=Normal SDRAM Mode +# bit31-4: 0 required + +DATA 0xFFD0141C 0x00000632 # DDR Mode +# bit2-0: 2, Burst Length (2 required) +# bit3: 0, Burst Type (0 required) +# bit6-4: 3, CAS Latency (CL) 3 +# bit7: 0, (Test Mode) Normal operation +# bit8: 0, (Reset DLL) Normal operation +# bit11-9: 3, Write recovery for auto-precharge (3 required) +# bit12: 0, Fast Active power down exit time (0 required) +# bit31-13: 0 required + +DATA 0xFFD01420 0x00000040 # DDR Extended Mode +# bit0: 0, DRAM DLL enabled +# bit1: 0, DRAM drive strength normal +# bit2: 0, ODT control Rtt[0] (Rtt=2, 150 ohm termination) +# bit5-3: 0 required +# bit6: 1, ODT control Rtt[1] (Rtt=2, 150 ohm termination) +# bit9-7: 0 required +# bit10: 0, differential DQS enabled +# bit11: 0 required +# bit12: 0, DRAM output buffer enabled +# bit31-13: 0 required + +DATA 0xFFD01424 0x0000F07F # DDR Controller Control High +# bit2-0: 0x7 required +# bit3: 1, MBUS Burst Chop disabled +# bit6-4: 0x7 required +# bit7: 0 required +# bit8: 0, no add writepath sample stage +# bit9: 0, no half clock cycle addition to dataout +# bit10: 0, 1/4 clock cycle skew enabled for addr/ctl signals +# bit11: 0, 1/4 clock cycle skew disabled for write mesh +# bit15-12: 0xf required +# bit31-16: 0 required + +DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing +# bit3-0: 0 required +# bit7-4: 2, 2 cycles from read command to assertion of M_ODT signal +# bit11-8: 5, 5 cycles from read command to de-assertion of M_ODT signal +# bit15-12: 5, 5 cycles from read command to assertion of internal ODT signal +# bit19-16: 8, 8 cycles from read command to de-assertion of internal ODT signal +# bit31-20: 0 required + +DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing +# bit3-0: 2, 2 cycles from write comand to assertion of M_ODT signal +# bit7-4: 5, 5 cycles from write command to de-assertion of M_ODT signal +# bit15-12: 5, 5 cycles from write command to assertion of internal ODT signal +# bit19-16: 8, 8 cycles from write command to de-assertion of internal ODT signal +# bit31-16: 0 required + +DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0 +DATA 0xFFD01504 0x07FFFFF1 # CS[0]n Size +# bit0: 1, Window enabled +# bit1: 0, Write Protect disabled +# bit3-2: 0x0, CS0 hit selected +# bit23-4: 0xfffff required +# bit31-24: 0x07, Size (i.e. 128MB) + +DATA 0xFFD01508 0x08000000 # CS[1]n Base address to 128Mb +DATA 0xFFD0150C 0x0FFFFFF0 # CS[1]n Size, window disabled +# bit0: 0, Window disabled +# bit1: 0, Write Protect disabled +# bit3-2: 0, CS1 hit selected +# bit23-4: 0xfffff required +# bit31-24: 0x0f, Size (i.e. 256MB) + +DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled +DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled + +DATA 0xFFD01494 0x003c0000 # DDR ODT Control (Low) +# bit3-0: 0b0000, (read) M_ODT[0] is not asserted during read from DRAM +# bit7-4: 0b0000, (read) M_ODT[1] is not asserted during read from DRAM +# bit15-8: 0 required +# bit19-16: 0b1100, (write) M_ODT[0] is asserted during write to DRAM CS2 and CS3 +# bit23-20: 0b0011, (write) M_ODT[1] is asserted during write to DRAM CS0 and CS1 +# bit31-24: 0 required + +DATA 0xFFD01498 0x00000000 # DDR ODT Control (High) +# bit1-0: 0, M_ODT[0] assertion is controlled by ODT Control Low register +# bit3-2: 0, M_ODT[1] assertion is controlled by ODT Control Low register +# bit31-4 0 required + +DATA 0xFFD0149C 0x0000E803 # CPU ODT Control +# bit3-0: 0b0011, internal ODT is asserted during read from DRAM bank 0-1 +# bit7-4: 0b0000, internal ODT is not asserted during write to DRAM bank 0-4 +# bit9-8: 0, Internal ODT assertion is controlled by fiels +# bit11-10: 2, M_DQ, M_DM, and M_DQS I/O buffer ODT 75 ohm +# bit13-12: 2, M_STARTBURST_IN I/O buffer ODT 75 ohm +# bit14: 1, M_STARTBURST_IN ODT enabled +# bit15: 1, DDR IO ODT Unit: Drive ODT calibration values +# bit20-16: 0, Pad N channel driving strength for ODT +# bit25-21: 0, Pad P channel driving strength for ODT +# bit31-26: 0 required + +DATA 0xFFD01480 0x00000001 # DDR Initialization Control +# bit0: 1, enable DDR init upon this register write +# bit31-1: 0, required + +# End of Header extension +DATA 0x0 0x0 diff --git a/boards.cfg b/boards.cfg index 2c555da..79999da 100644 --- a/boards.cfg +++ b/boards.cfg @@ -168,6 +168,7 @@ Active arm arm926ejs davinci omicron calimain Active arm arm926ejs kirkwood buffalo lsxl lschlv2 lsxl:LSCHLV2 Michael Walle <mich...@walle.cc> Active arm arm926ejs kirkwood buffalo lsxl lsxhl lsxl:LSXHL Michael Walle <mich...@walle.cc> Active arm arm926ejs kirkwood cloudengines - pogo_e02 - Dave Purdy <david.c.pu...@gmail.com> +Active arm arm926ejs kirkwood d-link dnskw dns320 dnskw:BOARD_IS_DNS320 Jamie Lentin <j...@lentin.co.uk> Active arm arm926ejs kirkwood d-link dnskw dns325 dnskw:BOARD_IS_DNS325 Stefan Herbrechtsmeier <ste...@code.herbrechtsmeier.net> Active arm arm926ejs kirkwood iomega - iconnect - Luka Perkov <l...@openwrt.org> Active arm arm926ejs kirkwood karo tk71 tk71 - - diff --git a/include/configs/dnskw.h b/include/configs/dnskw.h index b415216..e55fdc4 100644 --- a/include/configs/dnskw.h +++ b/include/configs/dnskw.h @@ -25,6 +25,16 @@ #endif /* CONFIG_BOARD_IS_DNS325 */ +#ifdef CONFIG_BOARD_IS_DNS320 +#define MACH_TYPE_DNS320 3985 +#define CONFIG_MACH_TYPE MACH_TYPE_DNS320 +#define CONFIG_IDENT_STRING "\nDNS-320" + +#define CONFIG_SYS_KWD_CONFIG $(SRCTREE)/$(CONFIG_BOARDDIR)/kwbimage.dns320.cfg +#define CONFIG_SYS_TCLK 166666667 /* 800Mhz */ + +#endif /* CONFIG_BOARD_IS_DNS320 */ + /* * High Level Configuration Options (easy to change) */ -- 2.0.0.rc2 _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot
