Short status update after recent ARM pull request http://lists.denx.de/pipermail/u-boot/2009-April/051803.html
Dirk Behme wrote: >> To avoid loosing the overview, here my list of pending OMAP3 patches >> ready to be applied. From my point of view there are no open comments >> on these which will prevent to apply them. But please correct if I >> overlooked anything or add what (patches? comments?) I missed. >> >> 1. OMAP3: Beagle: Set pinmux conditionally for Rev C boards >> http://lists.denx.de/pipermail/u-boot/2009-April/051013.html > > Mail > > http://lists.denx.de/pipermail/u-boot/2009-April/051459.html > > tells us that this should be applied to u-boot-arm next. But I can't > find it in gitweb > > http://git.denx.de/?p=u-boot/u-boot-arm.git;a=shortlog;h=refs/heads/next > > Did I miss something? > > Btw.: As initial patch and first update was sent ~1 day after merge > window close (Apr 4?) I hoped to have a chance to still get it into > master ;( Applied to u-boot-arm next. >> 2. OMAP3: Remove legacy NAND defines >> http://lists.denx.de/pipermail/u-boot/2009-April/050882.html > > Applied to u-boot-arm next. Request to move to master by Wolfgang. Copied to u-boot-arm master and part of above ARM pull request (still in u-boot-arm next, too?) >> 3. OMAP3: Fix timer handling to 1ms and CONFIG_SYS_HZ to 1000 >> http://lists.denx.de/pipermail/u-boot/2009-April/051178.html Pending http://lists.denx.de/pipermail/u-boot/2009-April/051518.html >> 4. OMAP3: Fix changed mmc init command >> http://lists.denx.de/pipermail/u-boot/2009-April/051179.html > > Applied to u-boot-arm master. ... and part of above ARM pull request. >> 5. OMAP3: Remove unused board-types >> http://lists.denx.de/pipermail/u-boot/2009-April/051338.html >> >> 6. OMAP3: Print correct silicon revision >> http://lists.denx.de/pipermail/u-boot/2009-April/051339.html > > Patches 5 & 6 replaced by update which includes switch to checkboard and > print_cpuinfo: > > OMAP3: Board specific updates (3 patches) > http://lists.denx.de/pipermail/u-boot/2009-April/051505.html > http://lists.denx.de/pipermail/u-boot/2009-April/051506.html > http://lists.denx.de/pipermail/u-boot/2009-April/051507.html All three patches applied to u-boot-arm master and part of above pull request. >> 7. Zoom2 respin II (10 patches) ... Recent remaining 5 Zoom2 patches http://lists.denx.de/pipermail/u-boot/2009-April/051651.html http://lists.denx.de/pipermail/u-boot/2009-April/051652.html http://lists.denx.de/pipermail/u-boot/2009-April/051653.html http://lists.denx.de/pipermail/u-boot/2009-April/051654.html http://lists.denx.de/pipermail/u-boot/2009-April/051655.html pending/under discussion http://lists.denx.de/pipermail/u-boot/2009-April/051792.html Summary: Besides the question if "Set pinmux conditionally for Rev C boards" should go from next to master, the 5 "Zoom2" and the "OMAP3: Fix timer handling to 1ms and CONFIG_SYS_HZ to 1000" are still open. Best regards Dirk _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot