On Thu, Dec 5, 2013 at 8:18 PM, Dennis Gilmore <den...@ausil.us> wrote:
> Signed-off-by: Dennis Gilmore <den...@ausil.us>
> ---
> include/configs/wandboard.h | 40 +++++++++++++++++++++++++++++++++++-----
> 1 file changed, 35 insertions(+), 5 deletions(-)
>
> diff --git a/include/configs/wandboard.h b/include/configs/wandboard.h
> index e9c7e64..02d8968 100644
> --- a/include/configs/wandboard.h
> +++ b/include/configs/wandboard.h
> @@ -40,6 +40,9 @@
> #define CONFIG_CONS_INDEX 1
> #define CONFIG_BAUDRATE 115200
>
> +/* enable generic distro config */
> +#define DISTRO_DEFAULTS 1
> +
> /* Command definition */
> #include <config_cmd_default.h>
>
> @@ -48,7 +51,6 @@
> #define CONFIG_CMD_BMODE
> #define CONFIG_CMD_SETEXPR
>
> -#define CONFIG_BOOTDELAY 5
>
> #define CONFIG_SYS_MEMTEST_START 0x10000000
> #define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 500 *
> SZ_1M)
> @@ -65,6 +67,9 @@
> #define CONFIG_CMD_MMC
> #define CONFIG_GENERIC_MMC
> #define CONFIG_BOUNCE_BUFFER
> +
> +#define CONFIG_BOOTDELAY 5
> +
> #define CONFIG_CMD_EXT2
> #define CONFIG_CMD_FAT
> #define CONFIG_DOS_PARTITION
> @@ -74,6 +79,11 @@
> #define CONFIG_CMD_DHCP
> #define CONFIG_CMD_MII
> #define CONFIG_CMD_NET
> +
> +#define CONFIG_OF_LIBFDT
> +#define CONFIG_CMD_BOOTZ
> +
> +/* Ethernet Configuration */
> #define CONFIG_FEC_MXC
> #define CONFIG_MII
> #define IMX_FEC_BASE ENET_BASE_ADDR
> @@ -113,8 +123,30 @@
> "fdt_high=0xffffffff\0" \
> "initrd_high=0xffffffff\0" \
> "fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \
> - "fdt_addr=0x11000000\0" \
> + "fdt_addr=0x11100000\0" \
> + "fdt_addr_r=0x11200000\0" \
> + "pxefile_addr_r=0x11300000\0" \
> + "scr_addr_r=0x11400000\0" \
> + "kernel_addr_r=0x11500000\0" \
> + "ramdisk_addr_r=0x13500000\0" \
> "boot_fdt=try\0" \
> + "bootcmd_setup=mmc rescan\0" \
> + "bootcmd_pxe=setenv bootfile \"\" ;dhcp; tftp ${fdt_addr}
> /dtb/${fdt_file}; pxe get; pxe boot\0" \
> + "bootcmd_disk_scr=ext2load ${boot_ifc} ${bootdevice} ${scr_addr_r}
> boot.scr &&
Why all the non-generic "ext2load"'s? use just "load", then it'll work
with both fat, ext2/3/4 & btrfs...
Regards,
--
Robert Nelson
http://www.rcn-ee.com/
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
