From: Lars Poeschel <poesc...@lemonage.de>
Phytec sells revision or version 3 of pcm051. It is labeled 1358.3 on
the board. The difference for u-boot is that is has other DDR3 RAM on it:
1 x MT41K256M16HA125E instead of 2 x MT41J256M8HX15E on revisions 1 and
2. Both configurations are 512 MiB.
Configure your u-boot build with pcm051_rev3 for the new RAM and
pcm051_rev1 for the old RAM configuration. Board revision 2 has to use
pcm051_rev1 also.
Signed-off-by: Lars Poeschel <poesc...@lemonage.de>
---
board/phytec/pcm051/board.c | 53 ++++++++++++++++++++++++++++++++++++++++-----
boards.cfg | 3 ++-
2 files changed, 49 insertions(+), 7 deletions(-)
diff --git a/board/phytec/pcm051/board.c b/board/phytec/pcm051/board.c
index e40b0bd..629bc52 100644
--- a/board/phytec/pcm051/board.c
+++ b/board/phytec/pcm051/board.c
@@ -49,6 +49,7 @@ const struct dpll_params *get_dpll_ddr_params(void)
return &dpll_ddr;
}
+#ifdef CONFIG_REV1
static const struct ddr_data ddr3_data = {
.datardsratio0 = MT41J256M8HX15E_RD_DQS,
.datawdsratio0 = MT41J256M8HX15E_WR_DQS,
@@ -82,6 +83,52 @@ static struct emif_regs ddr3_emif_reg_data = {
PHY_EN_DYN_PWRDN,
};
+void sdram_init(void)
+{
+ config_ddr(DDR_CLK_MHZ, MT41J256M8HX15E_IOCTRL_VALUE, &ddr3_data,
+ &ddr3_cmd_ctrl_data, &ddr3_emif_reg_data, 0);
+}
+#else
+static const struct ddr_data ddr3_data = {
+ .datardsratio0 = MT41K256M16HA125E_RD_DQS,
+ .datawdsratio0 = MT41K256M16HA125E_WR_DQS,
+ .datafwsratio0 = MT41K256M16HA125E_PHY_FIFO_WE,
+ .datawrsratio0 = MT41K256M16HA125E_PHY_WR_DATA,
+ .datadldiff0 = PHY_DLL_LOCK_DIFF,
+};
+
+static const struct cmd_control ddr3_cmd_ctrl_data = {
+ .cmd0csratio = MT41K256M16HA125E_RATIO,
+ .cmd0dldiff = MT41K256M16HA125E_DLL_LOCK_DIFF,
+ .cmd0iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
+
+ .cmd1csratio = MT41K256M16HA125E_RATIO,
+ .cmd1dldiff = MT41K256M16HA125E_DLL_LOCK_DIFF,
+ .cmd1iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
+
+ .cmd2csratio = MT41K256M16HA125E_RATIO,
+ .cmd2dldiff = MT41K256M16HA125E_DLL_LOCK_DIFF,
+ .cmd2iclkout = MT41K256M16HA125E_INVERT_CLKOUT,
+};
+
+static struct emif_regs ddr3_emif_reg_data = {
+ .sdram_config = MT41K256M16HA125E_EMIF_SDCFG,
+ .ref_ctrl = MT41K256M16HA125E_EMIF_SDREF,
+ .sdram_tim1 = MT41K256M16HA125E_EMIF_TIM1,
+ .sdram_tim2 = MT41K256M16HA125E_EMIF_TIM2,
+ .sdram_tim3 = MT41K256M16HA125E_EMIF_TIM3,
+ .zq_config = MT41K256M16HA125E_ZQ_CFG,
+ .emif_ddr_phy_ctlr_1 = MT41K256M16HA125E_EMIF_READ_LATENCY |
+ PHY_EN_DYN_PWRDN,
+};
+
+void sdram_init(void)
+{
+ config_ddr(DDR_CLK_MHZ, MT41K256M16HA125E_IOCTRL_VALUE, &ddr3_data,
+ &ddr3_cmd_ctrl_data, &ddr3_emif_reg_data, 0);
+}
+#endif
+
void set_uart_mux_conf(void)
{
enable_uart0_pin_mux();
@@ -95,12 +142,6 @@ void set_mux_conf_regs(void)
enable_board_pin_mux();
}
-
-void sdram_init(void)
-{
- config_ddr(DDR_CLK_MHZ, MT41J256M8HX15E_IOCTRL_VALUE, &ddr3_data,
- &ddr3_cmd_ctrl_data, &ddr3_emif_reg_data, 0);
-}
#endif
/*
diff --git a/boards.cfg b/boards.cfg
index 9fc77fb..c2e24d6 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -244,7 +244,8 @@ Active arm armv7 - armltd
vexpress
Active arm armv7 - armltd vexpress
vexpress_ca5x2 -
Matt Waddel <matt.wad...@linaro.org>
Active arm armv7 - armltd vexpress
vexpress_ca9x4 -
Matt Waddel <matt.wad...@linaro.org>
Active arm armv7 am33xx isee igep0033
igep0033 -
Enric Balletbo i Serra <eballe...@iseebcn.com>
-Active arm armv7 am33xx phytec pcm051
pcm051 pcm051
Lars Poeschel <poesc...@lemonage.de>
+Active arm armv7 am33xx phytec pcm051
pcm051_rev1 pcm051:REV1
Lars Poeschel <poesc...@lemonage.de>
+Active arm armv7 am33xx phytec pcm051
pcm051_rev3 pcm051:REV3
Lars Poeschel <poesc...@lemonage.de>
Active arm armv7 am33xx siemens dxr2
dxr2 -
Roger Meier <r.me...@siemens.com>
Active arm armv7 am33xx siemens pxm2
pxm2 -
Roger Meier <r.me...@siemens.com>
Active arm armv7 am33xx siemens rut
rut -
Roger Meier <r.me...@siemens.com>
--
1.8.4.2
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
