Re: [U-Boot] [PATCH 03/11] video: Add System-Mode configuration hook into mxsfb

[Otavio Salvador]

On Tue, Jul 30, 2013 at 7:45 PM, Marek Vasut <ma...@denx.de> wrote:
> Dear Otavio Salvador,
>
>> On Tue, Jul 30, 2013 at 6:37 PM, Marek Vasut <ma...@denx.de> wrote:
>> > Add hook that allow configuring SmartLCD attached the MXS LCDIF
>> > controller operating in System-Mode. This hook can be overriden
>> > by a platform-specific SmartLCD programming routine, which writes
>> > the SmartLCD specific values into it's registers.
>> >
>> > Also, this patch makes sure the SYNC signals are off for the
>> > SmartLCD case.
>> >
>> > Signed-off-by: Marek Vasut <ma...@denx.de>
>> > Cc: Anatolij Gustschin <ag...@denx.de>
>> > Cc: Fabio Estevam <fabio.este...@freescale.com>
>> > Cc: Otavio Salvador <ota...@ossystems.com.br>
>> > Cc: Stefano Babic <sba...@denx.de>
>> > ---
>> >
>> >  drivers/video/mxsfb.c |   16 ++++++++++++++++
>> >  1 file changed, 16 insertions(+)
>> >
>> > diff --git a/drivers/video/mxsfb.c b/drivers/video/mxsfb.c
>> > index dbc63a6..78709dd 100644
>> > --- a/drivers/video/mxsfb.c
>> > +++ b/drivers/video/mxsfb.c
>> > @@ -34,6 +34,17 @@
>> >
>> >  static GraphicDevice panel;
>> >
>> > +/**
>> > + * mxsfb_system_setup() - Fine-tune LCDIF configuration
>> > + *
>> > + * This function is used to adjust the LCDIF configuration. This is
>> > usually + * needed when driving the controller in System-Mode to operate
>> > an 8080 or + * 6800 connected SmartLCD.
>> > + */
>> > +__weak void mxsfb_system_setup(void)
>> > +{
>> > +}
>> > +
>> >
>> >  /*
>> >
>> >   * DENX M28EVK:
>> >   * setenv videomode
>> >
>> > @@ -88,6 +99,9 @@ static void mxs_lcd_init(GraphicDevice *panel,
>> >
>> >         writel(valid_data << LCDIF_CTRL1_BYTE_PACKING_FORMAT_OFFSET,
>> >
>> >                 &regs->hw_lcdif_ctrl1);
>> >
>> > +
>> > +       mxsfb_system_setup();
>> > +
>> >
>> >         writel((mode->yres << LCDIF_TRANSFER_COUNT_V_COUNT_OFFSET) |
>> >         mode->xres,
>> >
>> >                 &regs->hw_lcdif_transfer_count);
>> >
>> > @@ -115,8 +129,10 @@ static void mxs_lcd_init(GraphicDevice *panel,
>> >
>> >         /* Flush FIFO first */
>> >         writel(LCDIF_CTRL1_FIFO_CLEAR, &regs->hw_lcdif_ctrl1_set);
>> >
>> > +#ifndef CONFIG_VIDEO_MXS_MODE_SYSTEM
>>
>> Mode system or System mode?
>
> This is a name of configuration macro, CONFIG_VIDEO_MXS_MODE_SYSTEM . 
> Otherwise
> I do not understand what you are asking about.

I got this but accordingly to your commitlog it should be
CONFIG_VIDEO_MXS_SYSTEM_MODE to match the description. Any reason to
not use this name?

--
Otavio Salvador                             O.S. Systems
http://www.ossystems.com.br        http://projetos.ossystems.com.br
Mobile: +55 (53) 9981-7854            Mobile: +1 (347) 903-9750
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot