On Thu, Jun 13, 2013 at 05:53:17AM +0200, Heiko Schocher wrote: > move s_init from every board code to a common place. > > Signed-off-by: Heiko Schocher <h...@denx.de> > Cc: Tom Rini <tr...@ti.com> > Cc: Matt Porter <mpor...@ti.com> > Cc: Lars Poeschel <poesc...@lemonage.de> > Cc: Tom Rini <tr...@ti.com> > Cc: Enric Balletbo i Serra <eballe...@iseebcn.com> > > --- > This patch is based on the following patches: > > - [U-Boot,v2] arm, am33xx: move rtc32k_enable() to common place > http://patchwork.ozlabs.org/patch/248908/ > > - [U-Boot] arm, am33xx: move uart soft reset code to common place > http://patchwork.ozlabs.org/patch/248508/
These two apply best to u-boot-ti, and with them this patch doesn't
apply cleanly. Please sort that out.
The following adds moving ti814x_evm into the mix and I've sent Matt
some binaries to give a whirl to test on the board:
diff --git a/arch/arm/cpu/armv7/am33xx/board.c
b/arch/arm/cpu/armv7/am33xx/board.c
index 80b65fb..13b086a 100644
--- a/arch/arm/cpu/armv7/am33xx/board.c
+++ b/arch/arm/cpu/armv7/am33xx/board.c
@@ -151,6 +151,8 @@ int arch_misc_init(void)
}
#ifdef CONFIG_SPL_BUILD
+static struct wd_timer *wdtimer = (struct wd_timer *)WDT_BASE;
+
void rtc32k_enable(void)
{
struct rtc_regs *rtc = (struct rtc_regs *)RTC_BASE;
@@ -190,9 +192,6 @@ void uart_soft_reset(void)
}
#endif
-#ifndef CONFIG_TI81XX
-static struct wd_timer *wdtimer = (struct wd_timer *)WDT_BASE;
-
void s_init(void)
{
/*
@@ -202,7 +201,9 @@ void s_init(void)
*/
save_omap_boot_params();
- /* WDT1 is already running when the bootloader gets control
+#ifdef CONFIG_SPL_BUILD
+ /*
+ * WDT1 is already running when the bootloader gets control
* Disable it to avoid "random" resets
*/
writel(0xAAAA, &wdtimer->wdtwspr);
@@ -212,7 +213,6 @@ void s_init(void)
while (readl(&wdtimer->wdtwwps) != 0x0)
;
-#ifdef CONFIG_SPL_BUILD
/* Setup the PLLs and the clocks for the peripherals */
pll_init();
@@ -231,4 +231,3 @@ void s_init(void)
sdram_init();
#endif
}
-#endif
diff --git a/board/ti/ti814x/evm.c b/board/ti/ti814x/evm.c
index 6ad3dd8..08daee4 100644
--- a/board/ti/ti814x/evm.c
+++ b/board/ti/ti814x/evm.c
@@ -35,30 +35,10 @@
DECLARE_GLOBAL_DATA_PTR;
-#ifdef CONFIG_SPL_BUILD
-static struct wd_timer *wdtimer = (struct wd_timer *)WDT_BASE;
-#endif
-
static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
/* UART Defines */
#ifdef CONFIG_SPL_BUILD
-static void uart_enable(void)
-{
- /* UART softreset */
- uart_soft_reset();
-}
-
-static void wdt_disable(void)
-{
- writel(0xAAAA, &wdtimer->wdtwspr);
- while (readl(&wdtimer->wdtwwps) != 0x0)
- ;
- writel(0x5555, &wdtimer->wdtwspr);
- while (readl(&wdtimer->wdtwwps) != 0x0)
- ;
-}
-
static const struct cmd_control evm_ddr2_cctrl_data = {
.cmd0csratio = 0x80,
.cmd0dldiff = 0x04,
@@ -108,37 +88,12 @@ static const struct ddr_data evm_ddr2_data = {
.datauserank0delay = 1,
.datadldiff0 = 0x4,
};
-#endif
/*
* early system init of muxing and clocks.
*/
-void s_init(void)
+void board_enable_early_pinmux(void)
{
-#ifdef CONFIG_SPL_BUILD
- /*
- * Save the boot parameters passed from romcode.
- * We cannot delay the saving further than this,
- * to prevent overwrites.
- */
-#ifdef CONFIG_SPL_BUILD
- save_omap_boot_params();
-#endif
-
- /* WDT1 is already running when the bootloader gets control
- * Disable it to avoid "random" resets
- */
- wdt_disable();
-
- /* Enable timer */
- timer_init();
-
- /* Setup the PLLs and the clocks for the peripherals */
- pll_init();
-
- /* Enable RTC32K clock */
- rtc32k_enable();
-
/* Set UART pins */
enable_uart0_pin_mux();
@@ -147,22 +102,18 @@ void s_init(void)
/* Set Ethernet pins */
enable_enet_pin_mux();
+}
- /* Enable UART */
- uart_enable();
-
- gd = &gdata;
-
- preloader_console_init();
-
+void sdram_init(void)
+{
config_dmm(&evm_lisa_map_regs);
config_ddr(0, 0, &evm_ddr2_data, &evm_ddr2_cctrl_data,
&evm_ddr2_emif0_regs, 0);
config_ddr(0, 0, &evm_ddr2_data, &evm_ddr2_cctrl_data,
&evm_ddr2_emif1_regs, 1);
-#endif
}
+#endif
/*
* Basic board specific setup. Pinmux has been handled already.
Please fold into v2
Signed-off-by: Tom Rini <tr...@ti.com>
--
Tom
signature.asc
Description: Digital signature
_______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot
