Dear Sonic Zhang,

In message <1360223258-6945-4-git-send-email-sonic....@gmail.com> you wrote:
> 
> Add serial for bf60x.

There is a large number of checkpatch issues.  Please fix!!

> +/*
> + * All Blackfin system MMRs are padded to 32bits even if the register
> + * itself is only 16bits.  So use a helper macro to streamline this.
> + */
> +#define __BFP(m) u16 m; u16 __pad_##m
> +struct bfin_mmr_serial {
> +#if BFIN_UART_HW_VER == 2
> +     __BFP(dll);
> +     __BFP(dlh);
> +     __BFP(gctl);
> +     __BFP(lcr);
> +     __BFP(mcr);
> +     __BFP(lsr);
> +     __BFP(msr);
> +     __BFP(scr);
> +     __BFP(ier_set);
> +     __BFP(ier_clear);
> +     __BFP(thr);
> +     __BFP(rbr);
> +#else
> +     union {
> +             u16 dll;
> +             u16 thr;
> +             const u16 rbr;
> +     };
> +     const u16 __spad0;
> +     union {
> +             u16 dlh;
> +             u16 ier;
> +     };
> +     const u16 __spad1;
> +     const __BFP(iir);
> +     __BFP(lcr);
> +     __BFP(mcr);
> +     __BFP(lsr);
> +     __BFP(msr);
> +     __BFP(scr);
> +     const u32 __spad2;
> +     __BFP(gctl);
> +#endif

Sorry, but this is totally unreadable.


> +# define DO_MUX(port, mux_tx, mux_rx, tx, rx) \
> +     bfin_write_PORT##port##_MUX((bfin_read_PORT##port##_MUX() & 
> ~(PORT_x_MUX_##mux_tx##_MASK | PORT_x_MUX_##mux_rx##_MASK)) | 
> PORT_x_MUX_##mux_tx##_FUNC_1 | PORT_x_MUX_##mux_rx##_FUNC_1); \
> +     bfin_write_PORT##port##_FER(bfin_read_PORT##port##_FER() | P##port##tx 
> | P##port##rx);
> +     switch (CONFIG_UART_CONSOLE) {
> +     case 0:
> +             DO_MUX(G, 7, 7, 12, 13);
> +             break;  /* Port G; mux 7; PG12 and PG13 */
> +     case 1:
> +             DO_MUX(F, 3, 3, 6, 7);
> +             break;  /* Port F; mux 3; PF6 and PF7 */

This is totally unreadable.

This needs serious fixing.

Best regards,

Wolfgang Denk

-- 
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: w...@denx.de
Too bad that all the people who know how to run the country are  busy
driving taxicabs and cutting hair.                     - George Burns
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot

Reply via email to