On Thu, Nov 29, 2012 at 3:51 PM, Marek Vasut <ma...@denx.de> wrote: > Dear Yegor Yefremov, > >> On Thu, Nov 29, 2012 at 3:29 PM, Marek Vasut <ma...@denx.de> wrote: >> > Dear Yegor Yefremov, >> > >> >> On Thu, Nov 29, 2012 at 1:55 PM, Marek Vasut <ma...@denx.de> wrote: >> >> > Dear Yegor Yefremov, >> >> > >> >> >> On Thu, Nov 29, 2012 at 8:53 AM, Henrik Nordström >> >> >> >> >> >> <hen...@henriknordstrom.net> wrote: >> >> >> > tor 2012-11-29 klockan 07:27 +0100 skrev Marek Vasut: >> >> >> >> Dear yegorsli...@googlemail.com, >> >> >> >> >> >> >> >> > From: Yegor Yefremov <yegorsli...@googlemail.com> >> >> >> >> > >> >> >> >> > The driver code was taken from Linux kernel source: >> >> >> >> > drivers/net/phy/icplus.c >> >> >> >> > >> >> >> >> > Signed-off-by: Yegor Yefremov <yegorsli...@googlemail.com> >> >> >> >> >> >> >> >> [...] >> >> >> >> >> >> >> >> Is there any user for this PHY please? >> >> >> > >> >> >> > I don't have one, but know at least one user having one in an A10 >> >> >> > based "netbook". >> >> >> > >> >> >> > http://linux-sunxi.org/File:H6-netbook-mainboard.jpg >> >> >> >> >> >> I found these boards in kernel: >> >> >> >> >> >> arch/mips/configs/malta_defconfig:CONFIG_ICPLUS_PHY=m >> >> >> arch/mips/configs/bcm47xx_defconfig:CONFIG_ICPLUS_PHY=m >> >> >> arch/mips/configs/ip27_defconfig:CONFIG_ICPLUS_PHY=m >> >> >> arch/mips/configs/sead3_defconfig:CONFIG_ICPLUS_PHY=y >> >> >> arch/powerpc/configs/mpc512x_defconfig:CONFIG_ICPLUS_PHY=y >> >> >> arch/powerpc/configs/52xx/motionpro_defconfig:CONFIG_ICPLUS_PHY=y >> >> >> arch/powerpc/configs/83xx/mpc832x_rdb_defconfig:CONFIG_ICPLUS_PHY=y >> >> >> arch/powerpc/configs/mpc83xx_defconfig:CONFIG_ICPLUS_PHY=y >> >> >> arch/powerpc/configs/ppc6xx_defconfig:CONFIG_ICPLUS_PHY=m >> >> > >> >> > Sure, but the question/point is ... won't this be dead code in u-boot? >> >> > It won't once you add at least one board that actually uses it ... >> >> > adding it only so it's there will only cause it to bitrot and it'll >> >> > actually only add more burden to maintainers. >> >> >> >> It won't be dead code, because we will use it :-) Our board is >> >> derivative of BeagleBone & Co, so the whole support stuff is already >> >> in u-boot. >> > >> > You need to enable it for that board though ;-) >> >> Will do this as soon as we come near to the release. > > Release of what? The hardware?
Release of hardware and when two more patches hit main line u-boot: http://permalink.gmane.org/gmane.comp.boot-loaders.u-boot/147860 http://permalink.gmane.org/gmane.comp.boot-loaders.u-boot/147859 >> I'd like to have basic stuff mainlined before. > > Well, I'll leave that up to Joe anyway O.K. Yegor _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot
