Try running the installed version instead of the one in utilities. If you executed "sudo make install" there should be a copy in /usr/local/bin
--Greg On Fri, Aug 29, 2014 at 4:50 PM, Jon Behrens <j...@crimsonthread.com> wrote: > Thanks for the response Greg, but that doesn't work. Without being root: > > ./installmgr -ri CrossWire ESV > Couldn't find remote source [CrossWire] > > ./installmgr -sc > (Returns warnings and asks whether to proceed) > enable? [no] yes > Failed to sync config file with master remote source list. > > Jon > > > > On 08/29/2014 03:27 PM, Greg Hellings wrote: > > Try doing it as not root. I don't know why the docs suggest using root to > do the work, but try doing it in your local directory by running the > installmgr commands without being root. > > --Greg > > > On Fri, Aug 29, 2014 at 4:15 PM, Jon Behrens <j...@crimsonthread.com> > wrote: > >> Hello >> >> This started out as a C# binding question, but the problem is deeper than >> that. Basically >> I can't get the installmgr to do anything useful. I am new to Linux, but >> have been writing software on other platforms for ~50 years. >> >> To insure that my machine configuration was not the problem (I had >> installed Xiphos >> and BibleTime earlier), I set up a new virtual machine using VirtualBox >> and Mint 17. >> >> I updated all the packages and installed build-essentials. No other >> software. >> I downloaded Sword-1.73 and uncompressed it into a folder 'sword-1.7.3' >> under my >> home directory. >> >> I then followed the instructions in the INSTALL file and everything >> appeared to make >> correctly. >> >> I went to the utilities directory and ran the installmgr >> >> sudo ./installmgr -sc //Synch with master appeared to work >> sudo ./installmgr -r CrossWire //refresh remote source - appears to >> work, 411 packages >> sudo ./installmgr -ri CrossWire KJV //returns 'Remote source >> [CrossWire] does not make available module [KJV] >> >> sudo ./installmgr -rl CrossWire //list modules on CrossWire - sure >> enough, no KJV >> >> Went to ~/.sword/InstallMgr/20081216195754/mods.d/ and found kjv.conf. So >> refreshing the remote source finds KJV but install does not. >> >> OK - let's try a local install: >> >> Downloaded ESV.zip and unpacked it into the same directory (Downloads) >> >> sudo ./installmgr -li ~/Downloads/ESV.zip ESV >> Module [ESV] not available at path [/home/jsb/Downloads/ESV.zip] >> >> sudo ./installmgr -li ~/Downloads/ESV ESV >> Module [ESV] not available at path [/home/jsb/Downloads/ESV] >> >> sudo ./installmgr -li ~/Downloads/ESV/mods.d ESV >> Module [ESV] not available at path >> [/home/jsb/Downloads/ESV/mods.d] >> >> sudo ./installmgr -li ~/Downloads/ESV/modules ESV >> Module [ESV] not available at path >> [/home/jsb/Downloads/ESV/modules] >> >> Well, that didn't work. So let's try just extracting the archive into >> /usr/share/sword >> >> cd /usr/share/sword >> sudo unzip ~/Downloads/ESV.zip >> Archive: /home/jsb/Downloads/ESV.zip >> inflating: modules/texts/ztext/esv/nt.bzv >> inflating: modules/texts/ztext/esv/nt.bzs >> inflating: modules/texts/ztext/esv/ot.bzs >> inflating: modules/texts/ztext/esv/nt.bzz >> inflating: modules/texts/ztext/esv/ot.bzv >> inflating: modules/texts/ztext/esv/ot.bzz >> inflating: mods.d/esv.conf >> >> That's hopeful, let's try it out. >> >> cd ~/sword-1.7.3/examples/cmdline //previously made this >> project >> ./lookup ESV Jn.3.16 >> Could not find module [ESV]. Available modules: >> >> Note that the list of available modules is empty. >> >> So at this point I'm stuck. It is my hope to write a front end in C#, but >> I can't seem to get the package installed and working properly. >> >> I'd appreciate any help. >> Jon >> >> >> >> _______________________________________________ >> sword-devel mailing list: sword-devel@crosswire.org >> http://www.crosswire.org/mailman/listinfo/sword-devel >> Instructions to unsubscribe/change your settings at above page >> > > > > _______________________________________________ > sword-devel mailing list: > sword-devel@crosswire.orghttp://www.crosswire.org/mailman/listinfo/sword-devel > Instructions to unsubscribe/change your settings at above page > > > > _______________________________________________ > sword-devel mailing list: sword-devel@crosswire.org > http://www.crosswire.org/mailman/listinfo/sword-devel > Instructions to unsubscribe/change your settings at above page >
_______________________________________________ sword-devel mailing list: sword-devel@crosswire.org http://www.crosswire.org/mailman/listinfo/sword-devel Instructions to unsubscribe/change your settings at above page
