Add to smartmontools-database, please.
smartctl 6.4 2014-10-07 r4002 [x86_64-linux-4.2.0-22-lowlatency] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: ST120HM000-1G5142
Serial Number: Z4M00CNX
LU WWN Device Id: 5 000c50 02ff18988
Firmware Version: C675
User Capacity: 120 034 123 776 bytes [120 GB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: Solid State Device
Form Factor: 2.5 inches
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Sun Jan 3 19:59:59 2016 MSK
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM feature is: Unavailable
Rd look-ahead is: Enabled
Write cache is: Enabled
ATA Security is: Disabled, frozen [SEC2]
Wt Cache Reorder: Unavailable
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x02) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 5) seconds.
Offline data collection
capabilities: (0x19) SMART execute Offline immediate.
No Auto Offline data collection support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
No Selective Self-test supported.
SMART capabilities: (0x0002) Does not save SMART data before
entering power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 19) minutes.
SMART Attributes Data Structure revision number: 0
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate -OSR-- 166 166 006 - 0
5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0
9 Power_On_Hours -O--CK 085 085 000 - 14065
12 Power_Cycle_Count -O--CK 100 100 020 - 312
171 Unknown_Attribute -O--CK 100 100 000 - 0
172 Unknown_Attribute -O--CK 100 100 000 - 0
181 Program_Fail_Cnt_Total -O--CK 100 100 000 - 0
182 Erase_Fail_Count_Total -O--CK 100 100 000 - 0
194 Temperature_Celsius -O---K 030 000 000 - 30 (Min/Max 12/56)
201 Unknown_SSD_Attribute -O--CK 100 100 000 - 0
204 Soft_ECC_Correction -O--CK 100 100 000 - 0
231 Temperature_Celsius PO--C- 097 097 010 - 4
234 Unknown_Attribute -O--CK 100 100 000 - 32240
241 Total_LBAs_Written -O--CK 100 100 000 - 1395
242 Total_LBAs_Read -O--CK 100 100 000 - 767
250 Read_Error_Retry_Rate -O--CK 100 100 000 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log
0x04 GPL,SL R/O 8 Device Statistics log
0x07 GPL,SL R/O 2 Extended self-test log
0x10 GPL R/O 1 SATA NCQ Queued Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa8 GPL VS 521 Device vendor specific log
0xa8 SL VS 255 Device vendor specific log
0xb7 GPL,SL VS 4 Device vendor specific log
SMART Extended Comprehensive Error Log Version: 1 (5 sectors)
Device Error Count: 333 (device log contains only the most recent 20 errors)
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 333 [12] occurred at disk power-on lifetime: 14064 hours (586 days + 0
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 fe 00 00 00 00 00 00 40 08 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 05 00 fe 00 00 00 00 00 00 40 08 3d+04:37:05.740 SET FEATURES [Enable
APM]
60 00 08 00 a8 00 00 01 07 0b c8 40 08 3d+04:37:05.740 READ FPDMA QUEUED
60 00 68 00 a0 00 00 06 03 a3 38 40 08 3d+04:37:05.740 READ FPDMA QUEUED
60 00 d0 00 98 00 00 0b 4b 65 80 40 08 3d+04:37:05.740 READ FPDMA QUEUED
60 00 88 00 90 00 00 04 ac 57 68 40 08 3d+04:37:05.740 READ FPDMA QUEUED
Error 332 [11] occurred at disk power-on lifetime: 14058 hours (585 days + 18
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 fe 00 00 00 00 00 00 40 08 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 05 00 fe 00 00 00 00 00 00 40 08 2d+22:53:35.150 SET FEATURES [Enable
APM]
60 00 c8 00 c8 00 00 0b 5c 55 78 40 08 2d+22:53:35.150 READ FPDMA QUEUED
60 01 00 00 98 00 00 0d 69 c7 00 40 08 2d+22:53:35.150 READ FPDMA QUEUED
60 01 00 00 80 00 00 0d 69 c6 00 40 08 2d+22:53:35.150 READ FPDMA QUEUED
60 00 88 00 c0 00 00 02 06 06 80 40 08 2d+22:53:35.150 READ FPDMA QUEUED
Error 331 [10] occurred at disk power-on lifetime: 14037 hours (584 days + 21
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 fe 00 00 00 00 00 00 40 08 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 05 00 fe 00 00 00 00 00 00 40 08 2d+01:18:29.840 SET FEATURES [Enable
APM]
60 00 20 00 18 00 00 0b 9b 9d 80 40 08 2d+01:18:29.830 READ FPDMA QUEUED
60 01 20 00 10 00 00 0d ae f3 a8 40 08 2d+01:18:29.830 READ FPDMA QUEUED
60 04 58 00 08 00 00 0d ae ed c0 40 08 2d+01:18:29.830 READ FPDMA QUEUED
60 0d a8 00 00 00 00 0d ae df b8 40 08 2d+01:18:29.830 READ FPDMA QUEUED
Error 330 [9] occurred at disk power-on lifetime: 14036 hours (584 days + 20
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 fe 00 00 00 00 00 00 40 08 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 05 00 fe 00 00 00 00 00 00 40 08 2d+00:18:32.520 SET FEATURES [Enable
APM]
60 02 00 00 e8 00 00 0d 69 c4 00 40 08 2d+00:18:32.520 READ FPDMA QUEUED
60 00 08 00 e0 00 00 01 05 fc 18 40 08 2d+00:18:32.520 READ FPDMA QUEUED
60 00 68 00 d8 00 00 01 05 fc 98 40 08 2d+00:18:32.520 READ FPDMA QUEUED
60 00 58 00 c0 00 00 01 05 fc 40 40 08 2d+00:18:32.510 READ FPDMA QUEUED
Error 329 [8] occurred at disk power-on lifetime: 13987 hours (582 days + 19
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 fe 00 00 00 00 00 00 40 08 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 05 00 fe 00 00 00 00 00 00 40 08 00:00:31.980 SET FEATURES [Enable
APM]
60 01 00 00 28 00 00 0d 69 c9 00 40 08 00:00:31.980 READ FPDMA QUEUED
60 01 00 00 20 00 00 0d 69 c8 00 40 08 00:00:31.980 READ FPDMA QUEUED
60 00 20 00 18 00 00 0a 5c a5 20 40 08 00:00:31.980 READ FPDMA QUEUED
60 00 08 00 10 00 00 0b 88 eb 98 40 08 00:00:31.980 READ FPDMA QUEUED
Error 328 [7] occurred at disk power-on lifetime: 13923 hours (580 days + 3
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 fe 00 00 00 00 00 00 40 08 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 05 00 fe 00 00 00 00 00 00 40 08 7d+21:40:56.990 SET FEATURES [Enable
APM]
60 00 88 00 a0 00 00 0d e2 4b e0 40 08 7d+21:40:56.990 READ FPDMA QUEUED
60 00 18 00 98 00 00 04 ac 57 50 40 08 7d+21:40:56.990 READ FPDMA QUEUED
60 00 60 00 90 00 00 06 03 a5 58 40 08 7d+21:40:56.990 READ FPDMA QUEUED
60 00 20 00 88 00 00 0a 5c a5 20 40 08 7d+21:40:56.990 READ FPDMA QUEUED
Error 327 [6] occurred at disk power-on lifetime: 13922 hours (580 days + 2
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 fe 00 00 00 00 00 00 40 08 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 05 00 fe 00 00 00 00 00 00 40 08 7d+20:40:05.450 SET FEATURES [Enable
APM]
60 00 08 00 08 00 00 01 c5 fb c8 40 08 7d+20:40:05.440 READ FPDMA QUEUED
60 00 18 00 f0 00 00 01 c5 fb f0 40 08 7d+20:40:05.440 READ FPDMA QUEUED
60 00 08 00 e8 00 00 01 c5 fb e8 40 08 7d+20:40:05.440 READ FPDMA QUEUED
60 00 08 00 e0 00 00 01 c5 fb e0 40 08 7d+20:40:05.440 READ FPDMA QUEUED
Error 326 [5] occurred at disk power-on lifetime: 13743 hours (572 days + 15
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 51 00 fe 00 00 00 00 00 00 40 08 Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 05 00 fe 00 00 00 00 00 00 40 08 10:06:58.800 SET FEATURES [Enable
APM]
60 00 08 00 b8 00 00 01 07 0b c8 40 08 10:06:58.800 READ FPDMA QUEUED
60 00 08 00 b0 00 00 00 05 f7 80 40 08 10:06:58.800 READ FPDMA QUEUED
60 00 20 00 98 00 00 06 03 a5 38 40 08 10:06:58.800 READ FPDMA QUEUED
60 01 00 00 80 00 00 0d 69 bd 00 40 08 10:06:58.800 READ FPDMA QUEUED
SMART Extended Self-test Log Version: 1 (2 sectors)
Num Test_Description Status Remaining LifeTime(hours)
LBA_of_first_error
# 1 Short offline Completed without error 00% 14064 -
# 2 Extended offline Completed without error 00% 31 -
Selective Self-tests/Logging not supported
SCT Commands not supported
Device Statistics (GP Log 0x04)
Page Offset Size Value Description
1 ===== = = == General Statistics (rev 2) ==
1 0x008 4 312 Lifetime Power-On Resets
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0008 2 0 Device-to-host non-data FIS retries
0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy
0x000a 2 10 Device-to-host register FISes sent due to a COMRESET
0x000b 2 0 CRC errors within host-to-device FIS
0x000d 2 0 Non-CRC errors within host-to-device FIS
0x000f 2 0 R_ERR response for host-to-device data FIS, CRC
0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC
0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC
------------------------------------------------------------------------------
_______________________________________________
Smartmontools-database mailing list
Smartmontools-database@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/smartmontools-database
