Dear,
Please add this new disk to smarttools database.
Regards,
José
This email and any attached files is for the attention of the intended
recipient. The email and any attachments may contain material that is
confidential, privileged and/or attorney work product. If you are not the
intended recipient: (a) contact the sender immediately and delete from your
system all copies of the email including any attachments. (b) do not read,
print, retain, copy or disseminate this message or any part of it. Any such
unauthorized use may be unlawful. E-mail transmission cannot be guaranteed to
be secure or error-free as information could be intercepted, corrupted, lost,
destroyed, arrive late or incomplete, or contain viruses. The sender therefore
can not accept liability for any errors or omissions in the contents of this
message, which arise as a result of e-mail transmission. If verification is
required please request a hard-copy version. The Electrolux Group
www.electrolux.com
smartctl 6.2 2013-11-07 r3856 [x86_64-linux-4.1.13-5-default] (SUSE RPM)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: MB0500EAMZD
Serial Number: 9WJ0DAZB
LU WWN Device Id: 5 000c50 0270f1920
Firmware Version: HPG1
User Capacity: 500,107,862,016 bytes [500 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7200 rpm
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ATA8-ACS T13/1699-D revision 6
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Sat Dec 19 22:44:53 2015 PET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM feature is: Unavailable
Rd look-ahead is: Enabled
Write cache is: Disabled
ATA Security is: Unavailable
Wt Cache Reorder: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 609) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off
support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 84) minutes.
Conveyance self-test routine
recommended polling time: ( 3) minutes.
SCT capabilities: (0x103d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-- 071 063 044 - 13111878
3 Spin_Up_Time PO---- 097 097 000 - 0
4 Start_Stop_Count -O--CK 100 100 020 - 80
5 Reallocated_Sector_Ct PO--CK 100 100 036 - 2
7 Seek_Error_Rate POSR-- 085 060 030 - 342314345
9 Power_On_Hours -O--CK 053 053 000 - 41391
10 Spin_Retry_Count PO--C- 100 100 097 - 0
12 Power_Cycle_Count -O--CK 100 100 020 - 80
180 Unknown_HDD_Attribute PO-RCK 100 100 000 - 735899143
184 End-to-End_Error -O--CK 100 100 003 - 0
187 Reported_Uncorrect -O--CK 100 100 000 - 0
188 Command_Timeout -O--CK 100 100 000 - 0
189 High_Fly_Writes -O-RCK 100 100 000 - 0
190 Airflow_Temperature_Cel -O---K 075 060 045 - 25 (Min/Max 14/27)
191 G-Sense_Error_Rate -O--CK 099 099 000 - 2477
192 Power-Off_Retract_Count -O--CK 100 100 000 - 56
193 Load_Cycle_Count -O--CK 100 100 000 - 80
194 Temperature_Celsius -O---K 025 040 000 - 25 (0 14 0 0 0)
195 Hardware_ECC_Recovered -O-RC- 040 019 000 - 13111878
196 Reallocated_Event_Count PO--CK 100 100 036 - 2
197 Current_Pending_Sector -O--C- 100 100 000 - 0
198 Offline_Uncorrectable ----C- 100 100 000 - 0
199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 GPL,SL R/O 1 Summary SMART error log
0x02 GPL,SL R/O 5 Comprehensive SMART error log
0x03 GPL R/O 5 Ext. Comprehensive SMART error log
0x04 GPL,SL R/O 8 Device Statistics log
0x06 GPL,SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x09 GPL,SL R/W 1 Selective self-test log
0x10 GPL R/O 1 NCQ Command Error log
0x11 GPL R/O 1 SATA Phy Event Counters
0x12 GPL,SL R/O 1 SATA NCQ Queue Management log
0x21 GPL R/O 1 Write stream error log
0x22 GPL R/O 1 Read stream error log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa1 GPL,SL VS 20 Device vendor specific log
0xa2 GPL VS 2248 Device vendor specific log
0xa8 GPL,SL VS 129 Device vendor specific log
0xa9 GPL,SL VS 1 Device vendor specific log
0xb0 GPL VS 2928 Device vendor specific log
0xb6 GPL VS 1918 Device vendor specific log
0xbd GPL VS 252 Device vendor specific log
0xbe-0xbf GPL VS 65535 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (5 sectors)
Device Error Count: 1
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 1 [0] occurred at disk power-on lifetime: 29520 hours (1230 days + 0
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
10 -- 51 00 00 00 00 00 b3 d3 b8 00 00 Error: IDNF at LBA = 0x00b3d3b8 =
11785144
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
61 00 00 00 08 00 00 01 87 3d a0 40 00 26d+16:45:13.631 WRITE FPDMA QUEUED
61 00 00 00 08 00 00 01 87 3d 98 40 00 26d+16:45:13.631 WRITE FPDMA QUEUED
61 00 00 00 08 00 00 01 87 3d 90 40 00 26d+16:45:13.631 WRITE FPDMA QUEUED
61 00 00 00 08 00 00 01 87 3d 88 40 00 26d+16:45:13.631 WRITE FPDMA QUEUED
61 00 00 00 08 00 00 01 87 3d 80 40 00 26d+16:45:13.631 WRITE FPDMA QUEUED
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours)
LBA_of_first_error
# 1 Short offline Completed without error 00% 41391 -
# 2 Short offline Aborted by host 90% 11 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 522 (0x020a)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 25 Celsius
Power Cycle Min/Max Temperature: 14/27 Celsius
Lifetime Min/Max Temperature: 14/40 Celsius
Under/Over Temperature Limit Count: 0/1526
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 10 minutes
Min/Max recommended Temperature: 0/ 0 Celsius
Min/Max Temperature Limit: 0/ 0 Celsius
Temperature History Size (Index): 128 (34)
Index Estimated Time Temperature Celsius
35 2015-12-19 01:30 25 ******
... ..( 51 skipped). .. ******
87 2015-12-19 10:10 25 ******
88 2015-12-19 10:20 26 *******
89 2015-12-19 10:30 26 *******
90 2015-12-19 10:40 25 ******
91 2015-12-19 10:50 25 ******
92 2015-12-19 11:00 26 *******
93 2015-12-19 11:10 25 ******
... ..( 9 skipped). .. ******
103 2015-12-19 12:50 25 ******
104 2015-12-19 13:00 26 *******
105 2015-12-19 13:10 26 *******
106 2015-12-19 13:20 26 *******
107 2015-12-19 13:30 25 ******
... ..( 16 skipped). .. ******
124 2015-12-19 16:20 25 ******
125 2015-12-19 16:30 26 *******
... ..( 2 skipped). .. *******
0 2015-12-19 17:00 26 *******
1 2015-12-19 17:10 25 ******
... ..( 32 skipped). .. ******
34 2015-12-19 22:40 25 ******
SCT Error Recovery Control:
Read: 100 (10.0 seconds)
Write: 100 (10.0 seconds)
Device Statistics (GP Log 0x04)
Page Offset Size Value Description
1 ===== = = == General Statistics (rev 2) ==
1 0x008 4 80 Lifetime Power-On Resets
1 0x010 4 41391 Power-on Hours
1 0x018 6 10992607794 Logical Sectors Written
1 0x020 6 474045384 Number of Write Commands
1 0x028 6 492074058 Logical Sectors Read
1 0x030 6 9081032 Number of Read Commands
3 ===== = = == Rotating Media Statistics (rev 1) ==
3 0x008 4 41391 Spindle Motor Power-on Hours
3 0x010 4 41391 Head Flying Hours
3 0x018 4 80 Head Load Events
3 0x020 4 2 Number of Reallocated Logical Sectors
3 0x028 4 0 Read Recovery Attempts
4 ===== = = == General Errors Statistics (rev 1) ==
4 0x008 4 0 Number of Reported Uncorrectable Errors
4 0x010 4 0 Resets Between Cmd Acceptance and Completion
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x000a 2 48 Device-to-host register FISes sent due to a COMRESET
0x0001 2 0 Command failed due to ICRC error
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
------------------------------------------------------------------------------
_______________________________________________
Smartmontools-database mailing list
Smartmontools-database@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/smartmontools-database
