Hello.
smartctl -x output is in attachment.
Please note that sector sizes of '512 bytes logical, 4096 bytes physical'
because drive is
attached to HBA controller as JBOD drive and in this mode only 512 bytes
sector is available.
Best regards,
beelzebubbie.l...@gmail.com smartctl 5.42 2011-10-20 r3458 [x86_64-linux-3.8.13-gentoo-Jun13] (local build)
Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Device Model: Hitachi HTS727550A9E364
Serial Number: J3360081GM1H9C
LU WWN Device Id: 5 000cca 689c8a8a8
Firmware Version: JF3OA0E0
User Capacity: 500,107,862,016 bytes [500 GB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 6
Local Time is: Sat Jun 29 19:33:57 2013 ALMT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 39) The self-test routine was interrupted
by the host with a hard or soft reset.
Total time to complete Offline
data collection: ( 45) seconds.
Offline data collection
capabilities: (0x51) SMART execute Offline immediate.
No Auto Offline data collection support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 113) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-K 100 100 062 - 0
2 Throughput_Performance P-S--K 100 100 040 - 0
3 Spin_Up_Time PO---K 183 100 033 - 2
4 Start_Stop_Count -O--CK 100 100 000 - 120
5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0
7 Seek_Error_Rate POSR-K 100 100 067 - 0
8 Seek_Time_Performance P-S--K 100 100 040 - 0
9 Power_On_Hours -O--CK 100 100 000 - 187
10 Spin_Retry_Count PO--CK 100 100 060 - 0
12 Power_Cycle_Count -O--CK 100 100 000 - 119
183 Runtime_Bad_Block -O--CK 100 100 000 - 0
184 End-to-End_Error PO--CK 100 100 097 - 0
187 Reported_Uncorrect -O--CK 100 100 000 - 12884967424
188 Command_Timeout -O--CK 100 100 000 - 0
190 Airflow_Temperature_Cel -O---K 081 053 045 - 19 (Min/Max 15/23)
191 G-Sense_Error_Rate -O--CK 100 100 000 - 46
192 Power-Off_Retract_Count -O--CK 100 100 000 - 1441814
193 Load_Cycle_Count -O--CK 100 100 000 - 4647
196 Reallocated_Event_Count -O--CK 100 100 000 - 0
197 Current_Pending_Sector -O--CK 100 100 000 - 0
198 Offline_Uncorrectable ----CK 100 100 000 - 0
199 UDMA_CRC_Error_Count -OS-CK 100 100 000 - 0
223 Load_Retry_Count -O-R-K 100 100 000 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
ATA_READ_LOG_EXT (addr=0x00:0x00, page=0, n=1) failed: 48-bit ATA commands not
supported
Read GP Log Directory failed.
SMART Log Directory Version 1 [multi-sector log support]
SMART Log at address 0x00 has 1 sectors [Log Directory]
SMART Log at address 0x01 has 1 sectors [Summary SMART error log]
SMART Log at address 0x02 has 1 sectors [Comprehensive SMART error log]
SMART Log at address 0x06 has 1 sectors [SMART self-test log]
SMART Log at address 0x09 has 1 sectors [Selective self-test log]
SMART Log at address 0x80 has 16 sectors [Host vendor specific log]
SMART Log at address 0x81 has 16 sectors [Host vendor specific log]
SMART Log at address 0x82 has 16 sectors [Host vendor specific log]
SMART Log at address 0x83 has 16 sectors [Host vendor specific log]
SMART Log at address 0x84 has 16 sectors [Host vendor specific log]
SMART Log at address 0x85 has 16 sectors [Host vendor specific log]
SMART Log at address 0x86 has 16 sectors [Host vendor specific log]
SMART Log at address 0x87 has 16 sectors [Host vendor specific log]
SMART Log at address 0x88 has 16 sectors [Host vendor specific log]
SMART Log at address 0x89 has 16 sectors [Host vendor specific log]
SMART Log at address 0x8a has 16 sectors [Host vendor specific log]
SMART Log at address 0x8b has 16 sectors [Host vendor specific log]
SMART Log at address 0x8c has 16 sectors [Host vendor specific log]
SMART Log at address 0x8d has 16 sectors [Host vendor specific log]
SMART Log at address 0x8e has 16 sectors [Host vendor specific log]
SMART Log at address 0x8f has 16 sectors [Host vendor specific log]
SMART Log at address 0x90 has 16 sectors [Host vendor specific log]
SMART Log at address 0x91 has 16 sectors [Host vendor specific log]
SMART Log at address 0x92 has 16 sectors [Host vendor specific log]
SMART Log at address 0x93 has 16 sectors [Host vendor specific log]
SMART Log at address 0x94 has 16 sectors [Host vendor specific log]
SMART Log at address 0x95 has 16 sectors [Host vendor specific log]
SMART Log at address 0x96 has 16 sectors [Host vendor specific log]
SMART Log at address 0x97 has 16 sectors [Host vendor specific log]
SMART Log at address 0x98 has 16 sectors [Host vendor specific log]
SMART Log at address 0x99 has 16 sectors [Host vendor specific log]
SMART Log at address 0x9a has 16 sectors [Host vendor specific log]
SMART Log at address 0x9b has 16 sectors [Host vendor specific log]
SMART Log at address 0x9c has 16 sectors [Host vendor specific log]
SMART Log at address 0x9d has 16 sectors [Host vendor specific log]
SMART Log at address 0x9e has 16 sectors [Host vendor specific log]
SMART Log at address 0x9f has 16 sectors [Host vendor specific log]
SMART Log at address 0xe0 has 1 sectors [SCT Command/Status]
SMART Log at address 0xe1 has 1 sectors [SCT Data Transfer]
SMART Extended Comprehensive Error Log (GP Log 0x03) not supported
SMART Error Log Version: 1
No Errors Logged
SMART Extended Self-test Log (GP Log 0x07) not supported
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours)
LBA_of_first_error
# 1 Short offline Interrupted (host reset) 70% 187 -
# 2 Short offline Completed without error 00% 2 -
# 3 Short offline Completed without error 00% 1 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Error Write SCT Data Table command failed: Operation not permitted
Error Write SCT (Get) Error Recovery Control Command failed: Operation not
permitted
Warning: device does not support SCT (Get) Error Recovery Control command
SATA Phy Event Counters (GP Log 0x11) not supported
------------------------------------------------------------------------------
This SF.net email is sponsored by Windows:
Build for Windows Store.
http://p.sf.net/sfu/windows-dev2dev
_______________________________________________
Smartmontools-database mailing list
Smartmontools-database@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/smartmontools-database
