Hi Christian, the drive is a little strange, i.e. it never succeeded a 'long' test. Any such attempt was invariably "aborted by host" after a short while. Not sure what that means. Anyway, here is the output you requested:
$ smartctl -d usbjmicron,x -x /dev/sdb | smartctl 5.39.1 2010-01-28 r3054 [i686-pc-linux-gnu] (openSUSE RPM) | Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net | | === START OF INFORMATION SECTION === | Device Model: SAMSUNG HM252HX | Serial Number: C1042F121A031I | Firmware Version: 2AC101C4 | User Capacity: 250.059.350.016 bytes | Device is: Not in smartctl database [for details use: -P showall] | ATA Version is: 8 | ATA Standard is: ATA-8-ACS revision 6 | Local Time is: Mon Jul 25 22:02:26 2011 CEST | SMART support is: Available - device has SMART capability. | SMART support is: Enabled | | === START OF READ SMART DATA SECTION === | SMART overall-health self-assessment test result: PASSED | | General SMART Values: | Offline data collection status: (0x00) Offline data collection activity | was never started. | Auto Offline Data Collection: Disabled. | Self-test execution status: ( 24) The self-test routine was aborted by | the host. | Total time to complete Offline | data collection: (4200) seconds. | Offline data collection | capabilities: (0x5b) SMART execute Offline immediate. | Auto Offline data collection on/off support. | Suspend Offline collection upon new | command. | Offline surface scan supported. | Self-test supported. | No Conveyance Self-test supported. | Selective Self-test supported. | SMART capabilities: (0x0003) Saves SMART data before entering | power-saving mode. | Supports SMART auto save timer. | Error logging capability: (0x01) Error logging supported. | General Purpose Logging supported. | Short self-test routine | recommended polling time: ( 2) minutes. | Extended self-test routine | recommended polling time: ( 70) minutes. | SCT capabilities: (0x003f) SCT Status supported. | SCT Feature Control supported. | SCT Data Table supported. | | SMART Attributes Data Structure revision number: 16 | Vendor Specific SMART Attributes with Thresholds: | ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE | 1 Raw_Read_Error_Rate 0x002f 100 100 051 Pre-fail Always - 0 | 2 Throughput_Performance 0x0026 252 252 000 Old_age Always - 0 | 3 Spin_Up_Time 0x0023 091 091 025 Pre-fail Always - 2840 | 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 170 | 5 Reallocated_Sector_Ct 0x0033 252 252 010 Pre-fail Always - 0 | 7 Seek_Error_Rate 0x002e 252 252 051 Old_age Always - 0 | 8 Seek_Time_Performance 0x0024 252 252 015 Old_age Offline - 0 | 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 84 | 10 Spin_Retry_Count 0x0032 252 252 051 Old_age Always - 0 | 11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 13 | 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 80 | 191 G-Sense_Error_Rate 0x0022 100 100 000 Old_age Always - 38 | 192 Power-Off_Retract_Count 0x0022 252 252 000 Old_age Always - 0 | 194 Temperature_Celsius 0x0002 064 064 000 Old_age Always - 26 (Lifetime Min/Max 14/42) | 195 Hardware_ECC_Recovered 0x003a 100 100 000 Old_age Always - 0 | 196 Reallocated_Event_Count 0x0032 252 252 000 Old_age Always - 0 | 197 Current_Pending_Sector 0x0032 252 252 000 Old_age Always - 0 | 198 Offline_Uncorrectable 0x0030 252 252 000 Old_age Offline - 0 | 199 UDMA_CRC_Error_Count 0x0036 200 200 000 Old_age Always - 0 | 200 Multi_Zone_Error_Rate 0x002a 100 100 000 Old_age Always - 3 | 223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 13 | 225 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 2215 | | General Purpose Logging (GPL) feature set supported | General Purpose Log Directory Version 1 | SMART Log Directory Version 1 [multi-sector log support] | GP/S Log at address 0x00 has 1 sectors [Log Directory] | SMART Log at address 0x01 has 1 sectors [Summary SMART error log] | SMART Log at address 0x02 has 2 sectors [Comprehensive SMART error log] | GP Log at address 0x03 has 2 sectors [Ext. Comprehensive SMART error log] | SMART Log at address 0x06 has 1 sectors [SMART self-test log] | GP Log at address 0x07 has 2 sectors [Extended self-test log] | SMART Log at address 0x09 has 1 sectors [Selective self-test log] | GP Log at address 0x10 has 1 sectors [NCQ Command Error] | GP Log at address 0x11 has 1 sectors [SATA Phy Event Counters] | GP/S Log at address 0x80 has 16 sectors [Host vendor specific log] | GP/S Log at address 0x81 has 16 sectors [Host vendor specific log] | GP/S Log at address 0x82 has 16 sectors [Host vendor specific log] | GP/S Log at address 0x83 has 16 sectors [Host vendor specific log] | GP/S Log at address 0x84 has 16 sectors [Host vendor specific log] | GP/S Log at address 0x85 has 16 sectors [Host vendor specific log] | GP/S Log at address 0x86 has 16 sectors [Host vendor specific log] | GP/S Log at address 0x87 has 16 sectors [Host vendor specific log] | GP/S Log at address 0x88 has 16 sectors [Host vendor specific log] | GP/S Log at address 0x89 has 16 sectors [Host vendor specific log] | GP/S Log at address 0x8a has 16 sectors [Host vendor specific log] | GP/S Log at address 0x8b has 16 sectors [Host vendor specific log] | GP/S Log at address 0x8c has 16 sectors [Host vendor specific log] | GP/S Log at address 0x8d has 16 sectors [Host vendor specific log] | GP/S Log at address 0x8e has 16 sectors [Host vendor specific log] | GP/S Log at address 0x8f has 16 sectors [Host vendor specific log] | GP/S Log at address 0x90 has 16 sectors [Host vendor specific log] | GP/S Log at address 0x91 has 16 sectors [Host vendor specific log] | GP/S Log at address 0x92 has 16 sectors [Host vendor specific log] | GP/S Log at address 0x93 has 16 sectors [Host vendor specific log] | GP/S Log at address 0x94 has 16 sectors [Host vendor specific log] | GP/S Log at address 0x95 has 16 sectors [Host vendor specific log] | GP/S Log at address 0x96 has 16 sectors [Host vendor specific log] | GP/S Log at address 0x97 has 16 sectors [Host vendor specific log] | GP/S Log at address 0x98 has 16 sectors [Host vendor specific log] | GP/S Log at address 0x99 has 16 sectors [Host vendor specific log] | GP/S Log at address 0x9a has 16 sectors [Host vendor specific log] | GP/S Log at address 0x9b has 16 sectors [Host vendor specific log] | GP/S Log at address 0x9c has 16 sectors [Host vendor specific log] | GP/S Log at address 0x9d has 16 sectors [Host vendor specific log] | GP/S Log at address 0x9e has 16 sectors [Host vendor specific log] | GP/S Log at address 0x9f has 16 sectors [Host vendor specific log] | GP Log at address 0xbb has 4 sectors [Device vendor specific log] | GP Log at address 0xbc has 2 sectors [Device vendor specific log] | GP/S Log at address 0xe0 has 1 sectors [SCT Command/Status] | GP/S Log at address 0xe1 has 1 sectors [SCT Data Transfer] | | SMART Extended Comprehensive Error Log Version: 1 (2 sectors) | No Errors Logged | | SMART Extended Self-test Log Version: 1 (2 sectors) | Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error | # 1 Extended offline Aborted by host 80% 80 - | # 2 Extended offline Aborted by host 90% 75 - | # 3 Extended offline Aborted by host 90% 75 - | # 4 Extended offline Aborted by host 80% 75 - | # 5 Extended offline Aborted by host 80% 75 - | # 6 Short offline Completed without error 00% 75 - | | Note: selective self-test log revision number (0) not 1 implies that no selective self-test has ever been run | SMART Selective self-test log data structure revision number 0 | Note: revision number not 1 implies that no selective self-test has ever been run | SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS | 1 0 0 Aborted_by_host [80% left] (0-65535) | 2 0 0 Not_testing | 3 0 0 Not_testing | 4 0 0 Not_testing | 5 0 0 Not_testing | Selective self-test flags (0x0): | After scanning selected spans, do NOT read-scan remainder of disk. | If Selective self-test is pending on power-up, resume after 0 minute delay. | | SCT Status Version: 2 | SCT Version (vendor specific): 256 (0x0100) | SCT Support Level: 1 | Device State: Active (0) | Current Temperature: 26 Celsius | Power Cycle Min/Max Temperature: 24/30 Celsius | Lifetime Min/Max Temperature: 19/42 Celsius | Lifetime Average Temperature: 80 Celsius | Under/Over Temperature Limit Count: 0/0 | SCT Temperature History Version: 2 | Temperature Sampling Period: 5 minutes | Temperature Logging Interval: 5 minutes | Min/Max recommended Temperature: -5/80 Celsius | Min/Max Temperature Limit: -10/85 Celsius | Temperature History Size (Index): 128 (66) | | Index Estimated Time Temperature Celsius | 67 2011-07-25 11:25 26 ******* | 68 2011-07-25 11:30 29 ********** | 69 2011-07-25 11:35 27 ******** | 70 2011-07-25 11:40 29 ********** | 71 2011-07-25 11:45 26 ******* | 72 2011-07-25 11:50 24 ***** | 73 2011-07-25 11:55 25 ****** | 74 2011-07-25 12:00 26 ******* | 75 2011-07-25 12:05 27 ******** | 76 2011-07-25 12:10 27 ******** | 77 2011-07-25 12:15 28 ********* | 78 2011-07-25 12:20 28 ********* | 79 2011-07-25 12:25 28 ********* | 80 2011-07-25 12:30 29 ********** | ... ..( 3 skipped). .. ********** | 84 2011-07-25 12:50 29 ********** | 85 2011-07-25 12:55 30 *********** | ... ..( 8 skipped). .. *********** | 94 2011-07-25 13:40 30 *********** | 95 2011-07-25 13:45 29 ********** | 96 2011-07-25 13:50 29 ********** | 97 2011-07-25 13:55 25 ****** | 98 2011-07-25 14:00 30 *********** | 99 2011-07-25 14:05 24 ***** | 100 2011-07-25 14:10 27 ******** | 101 2011-07-25 14:15 29 ********** | 102 2011-07-25 14:20 29 ********** | 103 2011-07-25 14:25 30 *********** | 104 2011-07-25 14:30 30 *********** | 105 2011-07-25 14:35 30 *********** | 106 2011-07-25 14:40 31 ************ | ... ..( 18 skipped). .. ************ | 125 2011-07-25 16:15 31 ************ | 126 2011-07-25 16:20 32 ************* | ... ..( 2 skipped). .. ************* | 1 2011-07-25 16:35 32 ************* | 2 2011-07-25 16:40 31 ************ | ... ..( 5 skipped). .. ************ | 8 2011-07-25 17:10 31 ************ | 9 2011-07-25 17:15 30 *********** | 10 2011-07-25 17:20 31 ************ | 11 2011-07-25 17:25 30 *********** | ... ..( 15 skipped). .. *********** | 27 2011-07-25 18:45 30 *********** | 28 2011-07-25 18:50 22 *** | 29 2011-07-25 18:55 23 **** | 30 2011-07-25 19:00 25 ****** | 31 2011-07-25 19:05 25 ****** | 32 2011-07-25 19:10 27 ******** | 33 2011-07-25 19:15 28 ********* | 34 2011-07-25 19:20 28 ********* | 35 2011-07-25 19:25 28 ********* | 36 2011-07-25 19:30 29 ********** | ... ..( 8 skipped). .. ********** | 45 2011-07-25 20:15 29 ********** | 46 2011-07-25 20:20 28 ********* | 47 2011-07-25 20:25 28 ********* | 48 2011-07-25 20:30 29 ********** | 49 2011-07-25 20:35 28 ********* | 50 2011-07-25 20:40 29 ********** | 51 2011-07-25 20:45 29 ********** | 52 2011-07-25 20:50 28 ********* | 53 2011-07-25 20:55 28 ********* | 54 2011-07-25 21:00 29 ********** | 55 2011-07-25 21:05 29 ********** | 56 2011-07-25 21:10 30 *********** | 57 2011-07-25 21:15 29 ********** | 58 2011-07-25 21:20 28 ********* | 59 2011-07-25 21:25 29 ********** | 60 2011-07-25 21:30 30 *********** | 61 2011-07-25 21:35 29 ********** | 62 2011-07-25 21:40 29 ********** | 63 2011-07-25 21:45 29 ********** | 64 2011-07-25 21:50 24 ***** | 65 2011-07-25 21:55 26 ******* | 66 2011-07-25 22:00 26 ******* | | SATA Phy Event Counters (GP Log 0x11) | ID Size Value Description | 0x0001 4 0 Command failed due to ICRC error | 0x0002 4 0 R_ERR response for data FIS | 0x0003 4 0 R_ERR response for device-to-host data FIS | 0x0004 4 0 R_ERR response for host-to-device data FIS | 0x0005 4 0 R_ERR response for non-data FIS | 0x0006 4 0 R_ERR response for device-to-host non-data FIS | 0x0007 4 0 R_ERR response for host-to-device non-data FIS | 0x0008 4 0 Device-to-host non-data FIS retries | 0x0009 4 0 Transition from drive PhyRdy to drive PhyNRdy | 0x000a 4 0 Device-to-host register FISes sent due to a COMRESET | 0x000b 4 0 CRC errors within host-to-device FIS | 0x000d 4 0 Non-CRC errors within host-to-device FIS | 0x000f 4 0 R_ERR response for host-to-device data FIS, CRC | 0x0010 4 0 R_ERR response for host-to-device data FIS, non-CRC | 0x0012 4 0 R_ERR response for host-to-device non-data FIS, CRC | 0x0013 4 0 R_ERR response for host-to-device non-data FIS, non-CRC | 0x8e00 4 0 Vendor specific | 0x8e01 4 0 Vendor specific | 0x8e02 4 0 Vendor specific | 0x8e03 4 0 Vendor specific | 0x8e04 4 0 Vendor specific | 0x8e05 4 0 Vendor specific | 0x8e06 4 0 Vendor specific | 0x8e07 4 0 Vendor specific | 0x8e08 4 0 Vendor specific | 0x8e09 4 0 Vendor specific | 0x8e0a 4 0 Vendor specific | 0x8e0b 4 0 Vendor specific | 0x8e0c 4 0 Vendor specific | 0x8e0d 4 0 Vendor specific | 0x8e0e 4 0 Vendor specific | 0x8e0f 4 0 Vendor specific | 0x8e10 4 0 Vendor specific | 0x8e11 4 0 Vendor specific Take care, Peter ------------------------------------------------------------------------------ Storage Efficiency Calculator This modeling tool is based on patent-pending intellectual property that has been used successfully in hundreds of IBM storage optimization engage- ments, worldwide. Store less, Store more with what you own, Move data to the right place. Try It Now! http://www.accelacomm.com/jaw/sfnl/114/51427378/ _______________________________________________ Smartmontools-database mailing list Smartmontools-database@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/smartmontools-database
