Hello.
I have two Solaris 10 servers (release 10/09). The first one is a Sun M4000
Server with SPARC technology. The other one is a Sun Fire X4170 with x86 Intel
architecture. Both servers are attached via SAN to the same EMC Storage system.
The disks from the M4000 Server are cloned every nigh
> I'm not sure I didn't have dedup enabled. I might
> have.
> As it happens, the system rebooted and is now in
> single user mode.
> I'm trying another import. Most services are not
> running which should free ram.
>
> If it crashes again, I'll try the live CD while I see
> about more RAM.
Succ
> Tom,
>
> If you freshly installed the root pool, then those
> devices
> should be okay so that wasn't a good test. The other
> pools
> should remain unaffected by the install, and I hope,
> from
> the power failure.
Yes. I was able to import them and have since exported them.
>
> We've seen
Tom,
If you freshly installed the root pool, then those devices
should be okay so that wasn't a good test. The other pools
should remain unaffected by the install, and I hope, from
the power failure.
We've seen device info get messed up during a power failure,
which is why I asked.
If you don't
> Hi Tom,
>
> Did you boot from the OpenSolaris LiveCD and attempt
> to manually
> mount the data3 pool? The import might take some
> time.
I haven't tried that. I am booting from a new install to the hard drive though.
>
> I'm also curious whether the device info is coherent
> after the
> pow
Hi Tom,
Did you boot from the OpenSolaris LiveCD and attempt to manually
mount the data3 pool? The import might take some time.
I'm also curious whether the device info is coherent after the
power failure. You might review the device info for the root
pool to confirm.
If the device info is okay
My power supply failed. After I replaced it, I had issues staying up after
doing zpool import -f.
I reinstalled OpenSolaris 134 on my rpool and still had issues.
I have 5 pools:
rpool - 1*37GB
data - RAIDZ, 4*500GB
data1 - RAID1 2*750GB
data2 - RAID1 2*750GB
data3 - RAID1 2*2TB - WD20EARS
The s
And i just found out that one of my disk in the pool is showing missing labels
r...@essapl020-u006 # zdb -l /dev/dsk/emcpower0c
LABEL 0
version=4
name='emcpool1'
state=0
txg=6973090
pool_
didn't help .. tried
r...@essapl020-u006 # zpool import
pool: emcpool1
id: 5596268873059055768
state: UNAVAIL
status: One or more devices are missing from the system.
action: The pool cannot be imported. Attach the missing
devices and try again.
see: http://www.sun.com/msg/ZFS-
On 29.06.09 11:41, Ketan wrote:
I'm having following issue .. i import the zpool and it shows pool imported
correctly
'zpool import' only show what pools are available to import. In order to
actually import pool you need to to
zpool import emcpool1
but after few seconds when i issue comma
Hi,
you have to upgrade your pool:
The pool is formatted using an older on-disk version.
# *zpool upgrade -v*
Then it should works fine.
Kind regards,
Moutacim
Ketan schrieb:
I'm having following issue .. i import the zpool and it shows pool imported correctly but after few seconds when i i
Hi,
you have to upgrade your pool:
The pool is formatted using an older on-disk version.
Then it should works fine.
Kind regards,
Moutacim
Ketan schrieb:
I'm having following issue .. i import the zpool and it shows pool imported correctly but after few seconds when i issue command zpool lis
I'm having following issue .. i import the zpool and it shows pool imported
correctly but after few seconds when i issue command zpool list .. it does not
show any pool and when again i try to import it says device is missing in pool
.. what could be the reason for this .. and yes this all star
13 matches
Mail list logo
