Hi John,
The description of 'set interface l2 xcrw' in docs is that 'Add or delete a
Layer 2 to Layer 3 rewrite cross-connect'.
After put the gre tunnel in l2 mode , there is a 'Layer 2 to Layer 2 rewrite
cross-connect'. Is there anything wrong in my comprehension?
Thanks,
Xyxue
From: John
Hi Xyxue,
The L2 cross connect CLI via either xconnect or xcrw would put the source/input
interface into L2 mode and setup an one-directional cross connect to the
specified peer/output interface. The expectation is there should be a
xcrw/cross connect CLI for the other direction specifying the
Hi John，
I changed my configuration to that shown below:
create host-interface name eth1 mac 00:50:56:3a:32:d2
create host-interface name eth5 mac 00:50:56:31:35:92
set interface l3 host-eth1
set interface ip address host-eth1 11.1.1.2/24
create gre tunnel src 11.1.1.2 dst 11.1.1.1 teb
set inter
Dear Natalie,
What is the point of using DPDK marvel driver (which is actually just a wrapper
around musdk) if we already have native musdk support in vpp?
--
Damjan
> On 15 May 2018, at 08:48, Natalie Samsonov wrote:
>
> Hi,
>
> We are working now on upstreaming Marvell’s PMD support in VPP
Dear Damjan,
As I understood, it was a request to use DPDK plugin with all platforms and I
was asked to upstream Marvell DPDK plugin.
Best Regards,
Natalie
From: Damjan Marion [mailto:dmarion.li...@gmail.com]
Sent: Wednesday, May 16, 2018 16:03
To: Natalie Samsonov
Cc: Tina Tsou ; vpp-dev@list
Reminder of Sonar maintenance today
On 04/26/2018 10:02 AM, Vanessa Valderrama wrote:
>
> *Sonar 2018-05-16 - **2100 UTC to 0100 UTC*
>
> Sonar will be unavailable for approximately 2-3 hours depending on
> data transfer.
>
I apologize, Sonar maintenance has been rescheduled to 2018-05-17 due to
conflicts.
Thank you,
Vanessa
On 05/16/2018 09:12 AM, Vanessa Valderrama wrote:
>
> Reminder of Sonar maintenance today
>
>
> On 04/26/2018 10:02 AM, Vanessa Valderrama wrote:
>>
>> *Sonar 2018-05-16 - **2100 UTC to 0100 U
Hi
I am running VPP jut to route traffic between vlans, no routing
protocol involved.
I compiled the tap-inject plugin.
When I enable the plugin, I see I receive packets, but no packets go
out.
RX packets go up, nut no TX packets.
So 2 questions, is this
Hi Natalie,
Who requested that?
Thanks,
--
Damjan
> On 16 May 2018, at 15:33, Natalie Samsonov wrote:
>
> Dear Damjan,
>
> As I understood, it was a request to use DPDK plugin with all platforms and I
> was asked to upstream Marvell DPDK plugin.
>
> Best Regards,
> Natalie
>
> From: Damja
Hi Xyxue,
I have not used xcrw before to know how it is supposed to work, to cross
connect a layer 2 interface to a layer 3 stack. My suggestion was based on the
error shown by the packet trace you provided, that l2-output node found GRE
tunnel not to be set to L2 mode. If a GRE tunnel is cre
Hi all,
When vpp sends packets to a VM via a vhost-user interface, it will put the
packet in a queue (called `rxvq` in the code). It seems the default queue
size is 256 descriptors (I print rxvq->qsz_mask+1, and get 256). Is it
possible to increase the queue size, and how?
I followed the steps he
Hi Wang trying last version.
I have cannot find -lrtnl error.
Any idea ?
its working with last versions ?
Arch for platform 'vpp' is native
Finding source for router
Makefile fragment found in /vpp/build-data/packages/router.mk
Source found in /vpp/router
Yuliang,
Queue size is controlled by the driver, not the device which VPP is running as.
When you launch the VM via Qemu, at the end of virtio-net-pci, specify
rx_queue_size=xxx and/or tx_queue_size=xxx, where xxx is 512 or 1024.
You need Qemu-2.8.0 to specify rx_queue_size. You need to get Qem
13 matches
Mail list logo
