Hello
I have built an RTEMS 4.10.2 elf image for Phycore LPC3250. I am using
u-boot as my bootloader. Although I can boot the image in binary format,
unfortunately there is a problem to boot elf image with bootelf command.
after executing bootelf command u-boot get stuck in an infinite loop with
On Sep 15, 2012, at 4:40 PM, J.Hwan Kim wrote:
Is there limitation of the kernel size which u-boot loads?
No.
My kernel is very big, because I included the ramdisk into the kernel.
My kernel size is over 40MB.
When I load the kernel through u-boot, the prcedure hangs in the
boot step.
Th
On 09/14/2012 07:58 PM, Tom Rini wrote:
On Fri, Sep 14, 2012 at 06:29:02PM +0100, Jos?? Miguel Gon??alves wrote:
The MINI2416 board is based on a Samsung's S3C2416 SoC and has 64MB DDR2 SDRAM,
256MB NAND Flash, a LAN9220 Ethernet Controller and a WM8731 Audio CODEC.
This U-Boot port was impleme
On 09/14/2012 08:01 PM, Tom Rini wrote:
On Fri, Sep 14, 2012 at 07:45:40PM +0100, Jos? Miguel Gon?alves wrote:
On 14-09-2012 19:21, Marek Vasut wrote:
Dear Jos? Miguel Gon?alves,
NAND Flash driver with HW ECC for the S3C24XX SoCs.
Currently it only supports SLC NAND chips.
Signed-off-by: Jos
On 14/09/2012 18:13, Benoît Thébaudeau wrote:
> Hi Stefano,
>
Hi Benoît,
> On Friday, September 14, 2012 6:06:16 PM, Benoît Thébaudeau wrote:
>> Hi Fabio, Greg,
>>
>> On Friday, September 14, 2012 5:15:17 PM, Fabio Estevam wrote:
>>> On Fri, Sep 14, 2012 at 12:04 PM, Greg Topmiller
>>> wrote:
>
On 09/14/2012 08:08 PM, Tom Rini wrote:
On Fri, Sep 14, 2012 at 06:29:01PM +0100, Jos?? Miguel Gon??alves wrote:
Samsung's S3C24XX SoCs need this in order to generate a binary image
with the SPL and U-Boot concatenated.
Signed-off-by: Jos?? Miguel Gon??alves
---
Changes for v2:
- None
---
On 09/15/2012 07:03 PM, Marek Vasut wrote:
Dear José Miguel Gonçalves,
Jumping to board_init_r is not performed due to a bug on address
computation.
Is your CONFIG_SYS_TEXT_BASE configured correctly? I don't detect any
misbehavior on my arm926 boards.
Maybe because you are not using it to bu
Dear José Miguel Gonçalves,
> On 09/15/2012 07:03 PM, Marek Vasut wrote:
> > Dear José Miguel Gonçalves,
> >
> >> Jumping to board_init_r is not performed due to a bug on address
> >> computation.
> >
> > Is your CONFIG_SYS_TEXT_BASE configured correctly? I don't detect any
> > misbehavior on my
On 09/16/2012 11:06 AM, Marek Vasut wrote:
Dear José Miguel Gonçalves,
On 09/15/2012 07:03 PM, Marek Vasut wrote:
Dear José Miguel Gonçalves,
Jumping to board_init_r is not performed due to a bug on address
computation.
Is your CONFIG_SYS_TEXT_BASE configured correctly? I don't detect any
m
Hi
On Thursday 13 September 2012 15:31:39 Tom Rini wrote:
> On Fri, Sep 07, 2012 at 11:19:03AM +0200, Pavel Herrmann wrote:
> > On Friday 07 of September 2012 01:29:55 Marek Vasut wrote:
> > > Dear Pavel Herrmann,
> > >
> > > > This driver uses files as block devices, can be used for testing disk
Move all extern declarations of sata_dev_desc into a single header file.
Signed-off-by: Pavel Herrmann
---
drivers/block/ata_piix.c | 4 +---
drivers/block/dwc_ahsata.c | 1 +
drivers/block/dwc_ahsata.h | 2 --
drivers/block/fsl_sata.c | 3 +--
drivers/block/pata_bfin.c| 1 +
This driver uses files as block devices, can be used for testing disk
operations on sandbox.
A new command "sata_loop" is introduced to load files in runtime.
Signed-off-by: Pavel Herrmann
---
Changes for v5:
use common sata extern header - this requires "[PATCH] Fix checkpatch warnings
about
Dear Pavel Herrmann,
> Move all extern declarations of sata_dev_desc into a single header file.
>
> Signed-off-by: Pavel Herrmann
> ---
> drivers/block/ata_piix.c | 4 +---
> drivers/block/dwc_ahsata.c | 1 +
> drivers/block/dwc_ahsata.h | 2 --
> drivers/block/fsl_sata.c | 3 +-
On Sunday 16 September 2012 14:37:16 Marek Vasut wrote:
> Dear Pavel Herrmann,
> ...
> Won't include/sata.h work just fine ?
I feel include/sata.h is a "consumer-facing" header, and implementation
details such as the array used for all data-retention for command and drivers
should not be there.
Constants set with binary value (0b...) are not compiled
from old toolchain when used by the clrsetbits_le32 macro.
Replaces them with the corresponding hex value.
The error reported (for example with the mx6qsabrelite board)
is something like:
mx6qsabrelite.c:369:1: error: invalid suffix "b101"
Dear Pavel Herrmann,
> On Sunday 16 September 2012 14:37:16 Marek Vasut wrote:
> > Dear Pavel Herrmann,
> >
> > ...
> >
> > Won't include/sata.h work just fine ?
>
> I feel include/sata.h is a "consumer-facing" header, and implementation
> details such as the array used for all data-retention
2012년 09월 16일 14:14, Heiko Schocher 쓴 글:
Hello J.Hwan,
On 16.09.2012 01:40, J.Hwan Kim wrote:
Hi, everyone
Is there limitation of the kernel size which u-boot loads?
Only as I know the maximum RAM size (minus the size U-Boot needs)
My kernel is very big, because I included the ramdisk into
Dear José Miguel Gonçalves,
> On 09/16/2012 11:06 AM, Marek Vasut wrote:
> > Dear José Miguel Gonçalves,
> >
> >> On 09/15/2012 07:03 PM, Marek Vasut wrote:
> >>> Dear José Miguel Gonçalves,
> >>>
> Jumping to board_init_r is not performed due to a bug on address
> computation.
> >>>
Tom,
On Monday 10 September 2012 12:32:00 Tom Warren wrote:
> > -Original Message-
> > From: Stephen Warren [mailto:swar...@wwwdotorg.org]
> > Sent: Monday, September 10, 2012 12:08 PM
> > To: Marc Dietrich
> > Cc: u-boot@lists.denx.de; Tom Warren
> > Subject: Re: [PATCH 2/2] tegra: enable
On 09/16/2012 04:36 PM, Marek Vasut wrote:
Dear José Miguel Gonçalves,
On 09/16/2012 11:06 AM, Marek Vasut wrote:
Dear José Miguel Gonçalves,
On 09/15/2012 07:03 PM, Marek Vasut wrote:
Dear José Miguel Gonçalves,
Jumping to board_init_r is not performed due to a bug on address
computation
From: Daniel Schwierzeck
This series fixes the first bunch of gcc warnings appearing
when compiling for MIPS 64 bit.
For testing purposes all patches are also queued in branch testing at
git://git.denx.de/u-boot-mips.git. The support for MIPS64 and qemu_mips64
is already included.
Daniel Schwi
From: Daniel Schwierzeck
Signed-off-by: Daniel Schwierzeck
---
lib/vsprintf.c | 127 ++---
1 file changed, 77 insertions(+), 50 deletions(-)
diff --git a/lib/vsprintf.c b/lib/vsprintf.c
index e38a4b7..92a9232 100644
--- a/lib/vsprintf.c
+++ b
From: Daniel Schwierzeck
This fixes warnings when compiling with ELDK-5.2.1 for MIPS64:
vsprintf.c: In function 'put_dec':
vsprintf.c:258:9: warning: comparison of distinct pointer types lacks a cast
[enabled by default]
vsprintf.c:258:3: warning: passing argument 1 of '__div64_32' from incompa
From: Daniel Schwierzeck
Signed-off-by: Daniel Schwierzeck
---
common/cmd_elf.c | 134 +++
1 file changed, 67 insertions(+), 67 deletions(-)
diff --git a/common/cmd_elf.c b/common/cmd_elf.c
index 8266bba..0ca1ac2 100644
--- a/common/cmd_elf.c
From: Daniel Schwierzeck
This fixes warnings when compiling with ELDK-5.2.1 for MIPS64:
cmd_elf.c: In function 'load_elf_image_phdr':
cmd_elf.c:289:15: warning: cast to pointer from integer of different size
[-Wint-to-pointer-cast]
cmd_elf.c: In function 'load_elf_image_shdr':
cmd_elf.c:343:12:
Dear José Miguel Gonçalves,
> On 09/16/2012 04:36 PM, Marek Vasut wrote:
> > Dear José Miguel Gonçalves,
> >
> >> On 09/16/2012 11:06 AM, Marek Vasut wrote:
> >>> Dear José Miguel Gonçalves,
> >>>
> On 09/15/2012 07:03 PM, Marek Vasut wrote:
> > Dear José Miguel Gonçalves,
> >
> >>
Add i2c write command to write data from memory to i2c devices.
Signed-off-by: York Sun
---
common/cmd_i2c.c | 50 ++
1 file changed, 50 insertions(+)
diff --git a/common/cmd_i2c.c b/common/cmd_i2c.c
index 2cdc4ed..6099115 100644
--- a/common/cm
Signed-off-by: Ilya Yanok
---
drivers/usb/gadget/config.c |1 -
drivers/usb/gadget/epautoconf.c |1 -
drivers/usb/gadget/ether.c |1 -
drivers/usb/gadget/s3c_udc_otg.c |1 -
drivers/usb/gadget/usbstring.c |1 -
include/linux/usb/ch9.h | 514 ++
Current MUSB driver in U-Boot uses old UDC API while new gagdet
client drivers need new gadget API. Also current MUSB driver has
some significant limitations (like inability to handle tx for
endpoints other than ep0). So I think port of new Linux driver is
desirable.
This is initial port, performe
Backend driver for MUSB OTG controllers found on TI AM33xx and
TI81xx SoCs (tested with AM33xx only).
Signed-off-by: Ilya Yanok
---
Changes in v2:
- rename backend config option to CONFIG_USB_MUSB_DSPS
- we are providing host support now so add yourself to usb.h
arch/arm/include/asm/omap_musb
Linux usb/ch9.h seems to have all the same information (and more)
as usbdescriptors.h so use the former instead of the later one.
As a consequense of this change USB_SPEED_* values don't correspond
directly to EHCI speed encoding anymore, I've added necessary
recoding in EHCI driver. Also there is
AM33xx has support for dual port MUSB OTG controller. This patch
adds initialization for the controller using new MUSB gadget
driver and ether gadget.
Signed-off-by: Ilya Yanok
---
Changes in v2:
- init both musb IPs (conditionally) from arch_init not
from eth_initialize
arch/arm/cpu/armv7/
Enable musb gadget in Ethernet mode on port 0 and
musb host on port1.
Signed-off-by: Ilya Yanok
---
Changes in v2:
- host support enabled
- define CONFIG_ARCH_INIT as now musb_register() is called
from arch_init()
- use new config options
include/configs/am335x_evm.h | 27 ++
This patchset is a STAGE 1 of preparation of the stdio and serial subsys
for the driver model.
The idea of this patchset is:
1) Clean up the struct serial_device
Do a coding style cleanup.
2) Replace .init and .uninit with .start and .stop
This is to bring struct serial_device much closer t
Implement weak default_serial_console() function in serial_pxa
driver, which gets available in case CONFIG_SERIAL_MULTI is
enabled. This will get helpful in subsequent patches, which will
encapsulate PXA's struct serial_device instances in serial_pxa
driver.
Signed-off-by: Marek Vasut
Cc: Marek V
Do a simple cleanup of the struct serial_device and align it with
current coding style. Checkpatch now reports no errors.
Signed-off-by: Marek Vasut
Cc: Marek Vasut
Cc: Tom Rini
---
include/serial.h | 23 +++
1 file changed, 11 insertions(+), 12 deletions(-)
diff --git a
Move the registration of serial_XXuart ports from default
serial_initialize() into driver specific function called from
serial_initialize(). This slims down the serial_initialize() call
to a bare tracker of all possible serial port registration routines
in U-Boot.
The newly implemented pxa_serial_
This macro simplifies declaration of weak aliases for per-driver
functions, which register these drivers with the serial subsystem.
The idea here is to push serial_register() calls from serial.c into
the drivers. To avoid pile of ifdef construct as it is now, create
weak aliases to these functions,
Properly spell out the whole structure member names when an initialized
varible is instantiated from the struct serial_driver. In case the
structure definition for struct serial_driver undergoes reordering,
there will be no impact on variables defined based on this structure.
Signed-off-by: Marek
Move the registration of serial_smc and serial_scc ports from
default serial_initialize() into CPU specific function called from
serial_initialize(). This slims down the serial_initialize() call
to a bare tracker of all possible serial port registration routines
in U-Boot.
The exports of both seri
Move the registration of s5p_serialN_device ports from default
serial_initialize() into driver specific function called from
serial_initialize(). This slims down the serial_initialize() call
to a bare tracker of all possible serial port registration routines
in U-Boot.
The newly implemented s5p_se
Rename the serial_register_bfin_uart() to bfin_initialize_serial()
to be consistent with the rest of the naming. Next, remove it's
prototype from serial.h and properly insert it into serial.c as
the rest of the serial initialization functions.
Signed-off-by: Marek Vasut
Cc: Marek Vasut
Cc: Tom R
Rename .init() to .start() and .uninit() to .stop() in struct
serial_device. This allows aligning struct serial_device with
closer to struct stdio_dev. The real goal here is to allow
these two structures to converge together and eventually make
one to be a superset of the other.
Signed-off-by: Mar
Move the registration of serialN_device ports from default
serial_initialize() into driver specific function called from
serial_initialize(). This slims down the serial_initialize() call
to a bare tracker of all possible serial port registration routines
in U-Boot.
The newly implemented mpc512x_se
Remove the exports from serial.h as they are only used in the blackfin
serial driver. Furthermore, they are only used for registration, which
is handled already inside that driver and default_serial_port() call,
which is also handled in that driver.
Signed-off-by: Marek Vasut
Cc: Marek Vasut
Cc:
Make use of the newly implemented weak default_serial_console in
the serial_pxa driver. This removes all reimplementations of this
function from board files.
Signed-off-by: Marek Vasut
Cc: Marek Vasut
Cc: Tom Rini
---
board/balloon3/balloon3.c |5 -
board/palmld/pal
Make functions that are local-only static, so no hairy symbols
stick out of the serial_pxa driver file.
Signed-off-by: Marek Vasut
Cc: Marek Vasut
Cc: Tom Rini
---
drivers/serial/serial_pxa.c |6 +++---
1 file changed, 3 insertions(+), 3 deletions(-)
diff --git a/drivers/serial/serial_pxa
Move the registration of eserialN_device ports from default
serial_initialize() into driver specific function called from
serial_initialize(). This slims down the serial_initialize() call
to a bare tracker of all possible serial port registration routines
in U-Boot.
The newly implemented ns16550_s
Some of the boards using the mpc512x serial driver didn't properly
define which PSC console to use. This caused breakage when building
with CONFIG_SERIAL_MULTI enabled. Fix this by defining the default
PSC console.
Signed-off-by: Marek Vasut
Cc: Marek Vasut
Cc: Tom Rini
Cc: Anatolij Gustschin
Rework the emulation of serial console via JTAG from simple ad-hoc
implementation of serial port routines to CONFIG_SERIAL_MULTI and
enable CONFIG_SERIAL_MULTI unconditionally for blackfin.
In order for the JTAG serial console to take precedence over all
other serial ports available in system, imp
Move the registration of s3c24xx_serialN_device ports from
default serial_initialize() into driver specific function called from
serial_initialize(). This slims down the serial_initialize() call
to a bare tracker of all possible serial port registration routines
in U-Boot.
The newly implemented s3
Implement support for CONFIG_SERIAL_MULTI into au1x00 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the au1x00 driver. Also, add a weak implementation
of default_serial_conso
Move the registration of xuartlite_serialN_device ports from
default serial_initialize() into driver specific function called from
serial_initialize(). This slims down the serial_initialize() call
to a bare tracker of all possible serial port registration routines
in U-Boot.
The newly implemented
Remove the prototypes for zoom2_serial_deviceN from serial.h . This
can't be done right away, as they are referenced from the zoom2
config file. Therefore, adjust the code so the config file only
specifies number of the port. Then, replace the simple return in
default_serial_console() with a switch
Implement support for CONFIG_SERIAL_MULTI into JZ serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the JZ driver. Also, add a weak implementation
of default_serial_console() ret
Implement support for CONFIG_SERIAL_MULTI into asc serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the asc driver. Also, add a weak implementation
of default_serial_console() r
Implement support for CONFIG_SERIAL_MULTI into mpc5xx serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the mpc5xx driver. Also, add a weak implementation
of default_serial_conso
Implement support for CONFIG_SERIAL_MULTI into mpc8220 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the mpc8220 driver. Also, add a weak implementation
of default_serial_con
Implement support for CONFIG_SERIAL_MULTI into both SCC and SMC mpc8260
serial drivers. These drivers were so far only usable directly, but this
patch also adds support for the multi method. This allows using more than
one serial driver alongside the mpc8260 drivers. Also, add a weak
implementation
Implement support for CONFIG_SERIAL_MULTI into mpc85xx serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the mpc85xx driver. Also, add a weak implementation
of default_serial_con
Implement support for CONFIG_SERIAL_MULTI into iop480 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the iop480 driver. Also, add a weak implementation
of default_serial_conso
Implement support for CONFIG_SERIAL_MULTI into cpci750 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the cpci750 driver. Also, add a weak implementation
of default_serial_con
Implement support for CONFIG_SERIAL_MULTI into marvell serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the marvell driver. Also, add a weak implementation
of default_serial_con
Implement support for CONFIG_SERIAL_MULTI into leon2 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the leon2 driver. Also, add a weak implementation
of default_serial_console
Implement support for CONFIG_SERIAL_MULTI into amirix serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the amirix driver. Also, add a weak implementation
of default_serial_conso
Implement support for CONFIG_SERIAL_MULTI into ml2 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the ml2 driver. Also, add a weak implementation
of default_serial_console() r
Implement support for CONFIG_SERIAL_MULTI into evb64260 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the evb64260 driver. Also, add a weak implementation
of default_serial_c
Implement support for CONFIG_SERIAL_MULTI into p3mx serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the p3mx driver. Also, add a weak implementation
of default_serial_console()
Implement support for CONFIG_SERIAL_MULTI into leon3 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the leon3 driver. Also, add a weak implementation
of default_serial_console
Implement support for CONFIG_SERIAL_MULTI into cogent serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the cogent driver. Also, add a weak implementation
of default_serial_conso
Implement support for CONFIG_SERIAL_MULTI into altera serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the altera driver. Also, add a weak implementation
of default_serial_conso
Implement support for CONFIG_SERIAL_MULTI into altera_jtag serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the altera_jtag driver. Also, add a weak implementation
of default_se
Implement support for CONFIG_SERIAL_MULTI into MCF serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the MCF driver. Also, add a weak implementation
of default_serial_console() r
Implement support for CONFIG_SERIAL_MULTI into lpc32xx serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the lpc32xx driver. Also, add a weak implementation
of default_serial_con
Implement support for CONFIG_SERIAL_MULTI into atmel serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the atmel driver. Also, add a weak implementation
of default_serial_console
Implement support for CONFIG_SERIAL_MULTI into OpenCores serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the OpenCores driver. Also, add a weak implementation
of default_serial
Implement support for CONFIG_SERIAL_MULTI into s3c4510b serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the s3c4510b driver. Also, add a weak implementation
of default_serial_c
Implement support for CONFIG_SERIAL_MULTI into ns9750 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the ns9750 driver. Also, add a weak implementation
of default_serial_conso
Implement support for CONFIG_SERIAL_MULTI into s3c64xx serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the s3c64xx driver. Also, add a weak implementation
of default_serial_con
Implement support for CONFIG_SERIAL_MULTI into clps7111 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the clps7111 driver. Also, add a weak implementation
of default_serial_c
Implement support for CONFIG_SERIAL_MULTI into sandbox serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the sandbox driver. Also, add a weak implementation
of default_serial_con
Implement support for CONFIG_SERIAL_MULTI into ks8695 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the ks8695 driver. Also, add a weak implementation
of default_serial_conso
Implement support for CONFIG_SERIAL_MULTI into lh7a40x serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the lh7a40x driver. Also, add a weak implementation
of default_serial_con
Implement support for CONFIG_SERIAL_MULTI into lpc2292 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the lpc2292 driver. Also, add a weak implementation
of default_serial_con
Implement support for CONFIG_SERIAL_MULTI into ixp serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the ixp driver. Also, add a weak implementation
of default_serial_console() r
Implement support for CONFIG_SERIAL_MULTI into sh serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the sh driver. Also, add a weak implementation
of default_serial_console() ret
Remove the empty bodies from serial_* functions from MXS SPL code.
These empty implementations are now in common/serial.c instead so
declaring them also in the SPL code would cause a colision once
serial multi is enabled unconditionally.
Signed-off-by: Marek Vasut
Cc: Marek Vasut
Cc: Tom Rini
C
Having both USBTTY and CONFIG_SERIAL_MULTI enabled in SPL, the
usbtty.c file is protected in Makefile to not be compiled into
the SPL. Yet, the ns16550 serial driver does not contain such
protection. Add it to avoid missing symbol error.
Signed-off-by: Marek Vasut
Cc: Marek Vasut
Cc: Tom Rini
-
Implement support for CONFIG_SERIAL_MULTI into max3100 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the max3100 driver. Also, add a weak implementation
of default_serial_con
Implement support for CONFIG_SERIAL_MULTI into pl01x serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the pl01x driver. Also, add a weak implementation
of default_serial_console
Implement support for CONFIG_SERIAL_MULTI into sa1100 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the sa1100 driver. Also, add a weak implementation
of default_serial_conso
Implement support for CONFIG_SERIAL_MULTI into imx serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the imx driver. Also, add a weak implementation
of default_serial_console() r
Implement support for CONFIG_SERIAL_MULTI into s3c44b0 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the s3c44b0 driver. Also, add a weak implementation
of default_serial_con
Implement empty serial_* functions for SPL without serial
support enabled. This is imperative to haave once serial
multi is enabled unconditionally.
Signed-off-by: Marek Vasut
Cc: Marek Vasut
Cc: Tom Rini
---
common/serial.c | 12
1 file changed, 12 insertions(+)
diff --git a/c
Compile common/serial.c by default both into SPL and into non-SPL
builds, since CONFIG_SERIAL_MULTI is now the default state. Also
having common/serial.c in by default now, it's pointless to keep
-DCONFIG_SERIAL_MULTI in CPPFLAGS any longer, so remove it as well.
Signed-off-by: Marek Vasut
Cc: Ma
Implement support for CONFIG_SERIAL_MULTI into mxc serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the mxc driver. Also, add a weak implementation
of default_serial_console() r
Enable CONFIG_SERIAL_MULTI for all builds of U-Boot. That includes
both SPL builds and non-SPL builds, everything. To avoid poluting
this patch with removal of ifdef-endif constructions containing
CONFIG_SERIAL_MULTI, the CONFIG_SERIAL_MULTI is temporarily added
into CPPFLAGS in config.mk . This wi
Implement support for CONFIG_SERIAL_MULTI into netarm serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the netarm driver. Also, add a weak implementation
of default_serial_conso
If case the get_current() call fails before relocation, the U-Boot
must try to print an error message, fail and either reset or halt.
Such error is critical enough to halt the system, as it means the
system is in very bad state.
This is now also used in SPL, since CONFIG_SERIAL_MULTI is enabled
un
Remove any notion of CONFIG_SERIAL_MULTI from board config files.
Since CONFIG_SERIAL_MULTI is now enabled by default, it is useless
to specify this config option in the board config files. Therefore
remove it.
Signed-off-by: Marek Vasut
Cc: Marek Vasut
Cc: Tom Rini
Cc: Anatolij Gustschin
Cc:
1 - 100 of 111 matches
Mail list logo
