Sir,
We are having our own custom board based on the FDI design,on which we are
not able to mount USB. In the eaboard configuration files support for usb in
the u-boot is there and we have commands to check the usb inserted. But this
was not the case with FDI board,there were no commands for usb
Truncated CCs
Hi,
On 2012.10/25, Manukumar wrote:
> Dear All
>
> While board bring up in custom board
> iam getting below mentioned error
>
> I2C: ready
> DRAM: DDR: failed to read SPD from address
It seems you are using a DIMM for your memory (as opposed to directly soldered
on the board
Dear All
While board bring up in custom board
iam getting below mentioned error
I2C: ready
DRAM: DDR: failed to read SPD from address
I googled it but i am un able to rectify it..
Please resole ASAP
manukumar
___
U-Boot mailing list
U-Boot@lists.
Hello,
I resolved u-boot issues in u-boot level
but i am facing an issue in kernel level usb
detection can any suggest me to resolve this
issue.
manukumar
signal-networks
On Tue, 2012-07-10 at 04:17 +0200, Marek Vasut wrote:
> Dear Manukumar,
>
> > hello
> > I checked with the hardware spec
>
Dear Manukumar,
> hello
> I checked with the hardware spec
> in that
> P1020RDB: having connection like
> P1012processor -> PHY -> HUB -> ports
>
> whereas in custom board
> P1012processor -> phy -> port(single usb port)
This is fairy normal.
> In uboot source code initializing sequence of u-bo
Hi Manukumar,
On Mon, 09 Jul 2012 14:17:49 +0530, Manukumar
wrote:
> hello
> I checked with the hardware spec
> in that
> P1020RDB: having connection like
> P1012processor -> PHY -> HUB -> ports
>
> whereas in custom board
> P1012processor -> phy -> port(single usb port)
>
> In uboot source co
hello
I checked with the hardware spec
in that
P1020RDB: having connection like
P1012processor -> PHY -> HUB -> ports
whereas in custom board
P1012processor -> phy -> port(single usb port)
In uboot source code initializing sequence of u-boot
is below:
1.usb_init()
2.usb_scan_devices()
3.usb_new_
Dear Albert ARIBAUD,
> Hi Manukumar,
>
> On Thu, 05 Jul 2012 15:57:49 +0530, Manukumar
>
> wrote:
> > Hello,
> >
> > I have connected USB hard disk to P1020RB
>
> Which board is this? Neither "git grep -i P1020RB" nor "find . iname
> '*P1020RB*'" yield any result.
Ain't it P1020RDB?
> > and
Hi Manukumar,
On Thu, 05 Jul 2012 15:57:49 +0530, Manukumar
wrote:
> Hello,
>
> I have connected USB hard disk to P1020RB
Which board is this? Neither "git grep -i P1020RB" nor "find . iname
'*P1020RB*'" yield any result.
> and in command prompt(u-boot) i used
> command
> => usb start
> (Re)s
Hello,
I have connected USB hard disk to P1020RB
and in command prompt(u-boot) i used
command
=> usb start
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 3 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
=> usb
Hi,
I am using OMAPL137EVM, using DaVinci-PSP-SDK-03.20.00.14 package and trying
to boot from USB on u-boot.
While configuring u-boot for USB support we have enabled macro's
CONFIG_USB_DA8XX and CONFIG_USB_STORAGE
in include/configs/da8xx_evm.h following below link :
http://processors.wiki.ti
11 matches
Mail list logo
