On 16/10/2014 03:16, Nikolay Dimitrov wrote:
> Hi Sean, guys,
>
> On 10/15/2014 10:47 AM, Sean Cross wrote:
>> On 15/10/2014 12:47, Nikolay Dimitrov wrote:
>>> Hi Marek,
>>>
>>> On 10/15/2014 12:38 AM, Marek Vasut wrote:
>>>> On Sunday, Octob
On 15/10/2014 12:47, Nikolay Dimitrov wrote:
> Hi Marek,
>
> On 10/15/2014 12:38 AM, Marek Vasut wrote:
>> On Sunday, October 12, 2014 at 08:33:21 AM, Sean Cross wrote:
>>> On 12/10/2014 05:04, Fabio Estevam wrote:
>>>> On Sat, Oct 11, 2014 at 11:21 AM, Sean
On 12/10/2014 05:04, Fabio Estevam wrote:
> On Sat, Oct 11, 2014 at 11:21 AM, Sean Cross wrote:
>
>>> Ok, understood. Just curious: which Ethernet PHY is used on the novena
>>> board?
>> It's the same Micrel PHY used on the Sabrelite, the KSZ9021.
> nitro
On 11/10/2014 21:56, Fabio Estevam wrote:
> Hi Nikolay,
>
> On Sat, Oct 11, 2014 at 2:01 AM, Nikolay Dimitrov wrote:
>
>> We had some discussions about the PHY reset sequence and timing, but still
>> not a common opinion, so I suggested to leave this fix for a consequent
>> patch.
> Ok, understood
Hi Nikolay,
On 08/10/2014 23:35, picmas...@mail.bg wrote:
> Hi Sean,
>
> - Цитат от Sean Cross (x...@kosagi.com), на 08.10.2014 в 10:47 -
>
>> On 08/10/2014 05:55, Nikolay Dimitrov wrote:
>>> Hi Marek,
>>>
>>> I'm marking only the criti
On 09/10/2014 07:59, Marek Vasut wrote:
> On Wednesday, October 08, 2014 at 05:35:44 PM, picmas...@mail.bg wrote:
>> Hi Sean,
> Hi all,
Hello
>
>> - Цитат от Sean Cross (x...@kosagi.com), на 08.10.2014 в 10:47 -
>>
>>> On 08/10/2014 05:55, N
On 08/10/2014 05:55, Nikolay Dimitrov wrote:
> Hi Marek,
>
> I'm marking only the critical issues that are left unfixed from
> previous conversations, to speed-up the process a little bit.
> I'll send later patches for the non-critical issues to spare you the
> extra work (and I'm sure my construct
On 07/10/2014 00:02, Marek Vasut wrote:
> Add support for the Kosagi Novena board. Currently supported are:
> - I2C busses
> - FEC Ethernet
> - MMC0, MMC1, Booting from MMC
> - SATA
> - USB ports
> - USB Ethernet
>
This patch looks good. It resets the FPGA, muxes the correct UART
lines, and detect
Hi Marek, Nikolay,
I thought I responded, but it might have gotten lost. I'm sorry about that.
I've taken a closer look, and responded below.
On 24/9/2014 5:40 PM, Marek Vasut wrote:
On Wednesday, September 24, 2014 at 04:46:42 AM, Nikolay Dimitrov wrote:
Hi Marek,
Following are some commen
On 28/09/2014 04:19, Marek Vasut wrote:
> On Wednesday, September 24, 2014 at 06:57:06 PM, Sean Cross wrote:
>
> [...]
>>> +#define NOVENA_AUDIO_PWRON IMX_GPIO_NR(5, 17)
>>> +#define NOVENA_HDMI_GHOST_HPD IMX_GPIO_NR(5, 4)
>>
I asked Bunnie about this, and the routing is 50 ohms.
On 24 September, 2014 5:40:59 pm GMT+08:00, Marek Vasut wrote:
>On Wednesday, September 24, 2014 at 04:46:42 AM, Nikolay Dimitrov
>wrote:
>> Hi Marek,
>>
>> Following are some comments about FEC Ethernet:
>>
>> On 09/23/2014 01:18 PM, Mare
On 29/8/2014 5:30 PM, Marek Vasut wrote:
Add support for the Kosagi Novena board. Currently supported are:
- I2C busses
- FEC Ethernet
- MMC0, MMC1, Booting from MMC
- SATA
- USB ports
- USB Ethernet
Signed-off-by: Marek Vasut
---
arch/arm/Kconfig | 4 +
board/kosagi/noven
12 matches
Mail list logo
