Since the type of "ext_csd" was array of char, the following
calculation might fail when the value of ext_csd[EXT_CSD_SEC_CNT]
was minus.
capacity = ext_csd[EXT_CSD_SEC_CNT] << 0
| ext_csd[EXT_CSD_SEC_CNT + 1] << 8
| ext_csd[EXT_CSD_SEC_CNT +
>On 06/06/2012 10:16 PM, Xie Shaohui-B21989 wrote:
>>> -Original Message-
>>> From: Wood Scott-B07421
>>> Sent: Thursday, June 07, 2012 2:19 AM
>>> To: Xie Shaohui-B21989
>>> Cc: Wood Scott-B07421; u-boot@lists.denx.de; Tabi Timur-B04825
>>> Subject: Re: [U-Boot] [PATCH] powerpc/CoreNet: ad
The controller can control high capacity cards. So, the patch adds
the flag. If the flag is not set, "mmcinfo" will fail when a high
capacity card is used.
Signed-off-by: Yoshihiro Shimoda
---
drivers/mmc/sh_mmcif.c |2 +-
1 files changed, 1 insertions(+), 1 deletions(-)
diff --git a/driver
Dear Dinh,
In message
<71b37e0559ac6849a68c5ba94c509fb458298d3...@sj-itmsg02.altera.priv.altera.com>
you wrote:
>
> > Sorry, but this commit message is misleading - I was expecting to see
> > something like udelay() in the code, but there wasn't any...
>
> Combining the 2 individual writes int
Dear Dinh,
In message <1339104480-6191-1-git-send-email-dingu...@altera.com> you wrote:
> This commit is an add-on to f6c4191f. There are a few other registers where
> consecutive writes must have a delay.
Sorry, but this commit message is misleading - I was expecting to see
something like udelay
On Thu, 2012-06-07 at 15:27 +0200, Luka Perkov wrote:
> Hi all,
>
> On Sun, May 27, 2012 at 11:44:51PM +0200, Luka Perkov wrote:
> > The kwboot program boots boards based on Marvell's Kirkwood platform
> > via Xmodem over their integrated UART.
> >
> > Signed-off-by: Daniel Stodden
> > Acked-by:
This commit is an add-on to f6c4191f. There are a few other registers where
consecutive writes must have a delay.
Signed-off-by: Dinh Nguyen
---
drivers/net/designware.c |4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/drivers/net/designware.c b/drivers/net/designware.c
Dear Anatolij Gustschin,
In message <20120605095753.0b080872@wker> you wrote:
> Hello Wolfgang,
>
> The following changes since commit 4398d55991eb3c2484a2a8e991d701e5d7a64874:
>
> net: sh-eth: Add support Gigabit of SH7734 (2012-05-23 17:53:09 -0500)
>
> are available in the git repository a
Dear Rudy,
In message
<7a6a685f2ad2c242812385088f128c121c5a332...@ausp01vmbx02.collaborationhost.net>
you wrote:
>
> The latest version does not appear to contain support for the the
> twrmpc5125 processor because the following command issued in the
> u-boot installation directory yields nothin
Dear Andreas =?iso-8859-1?Q?Bie=DFmann?=,
In message <20120604104547.ga29...@azuregos.er.corscience.de> you wrote:
> The following changes since commit 4398d55991eb3c2484a2a8e991d701e5d7a64874:
>
> net: sh-eth: Add support Gigabit of SH7734 (2012-05-23 17:53:09 -0500)
>
> are available in the
Dear Daniel Schwierzeck,
In message
<1338761093-27598-1-git-send-email-daniel.schwierz...@googlemail.com> you wrote:
> Dear Wolfgang,
>
> please pull some checkpatch.pl cleanups for MIPS.
>
> The following changes since commit 4398d55991eb3c2484a2a8e991d701e5d7a64874:
>
> net: sh-eth: Add su
Dear Nobuhiro Iwamatsu,
In message
you wrote:
> Dear Wolfgang Denk.
>
> Please pull from git://git.denx.de/u-boot-sh master.
>
> Best regards,
> Nobuhiro
>
> The following changes since commit 4398d55991eb3c2484a2a8e991d701e5d7a64874:
>
> net: sh-eth: Add support Gigabit of SH7734 (2012-
Dear Marek Vasut,
In message <1337955286-22345-1-git-send-email-ma...@denx.de> you wrote:
> This patch conditionally defines flush_dcache_range() and
> invalidate_dcache_range() on MPC8xxx, to avoid EHCI complaining,
> resulting in the following output:
>
> $ ARCH=powerpc CROSS_COMPILE=powerpc-li
Dear Zang Roy-R61911,
In message <201206071134.02455.ma...@denx.de> Marek Vasut wrote:
>
> The patch "[PATCH V2] MPC8xxx: Define cache ops for USB" wasn't applied yet
> for
> some reason. It fixes the issue.
>
> > Hi, Marek
> >
> > When I build P5020DS_config with the current u-boot head, I g
Dear Xie Shaohui-B21989,
In message
you wrote:
>
> >I want to get rid if config.mk files to the extend possible - and here I
> >see no need for a new one.
> [Xie Shaohui] Actually, I was hesitate to use the config.mk file, I found
> other person define the "CONFIG_XXX_CONFIG" in header files,
On 06/07/2012 11:04 AM, Sughosh Ganu wrote:
> On Thu Jun 07, 2012 at 10:36:53AM -0600, Stephen Warren wrote:
>> On 06/07/2012 01:15 AM, Sughosh Ganu wrote:
>>> On Wed Jun 06, 2012 at 10:44:59AM -0600, Stephen Warren wrote:
On 06/05/2012 03:20 PM, Allen Martin wrote:
>>>
>>>
>>>
> diff --g
From: Fabio Estevam
CONFIG_MII_GASKET is not defined anywhere, so remove it.
Signed-off-by: Fabio Estevam
---
include/configs/mx53ard.h |1 -
1 files changed, 0 insertions(+), 1 deletions(-)
diff --git a/include/configs/mx53ard.h b/include/configs/mx53ard.h
index f48a41e..f59960e 100644
-
On 06/07/2012 12:19 PM, Steve Sakoman wrote:
> Commit 418396e212b59bf907dbccad997ff50f7eb61b16 introduced a
> bug that causes nand read and nand write to crash in strcmp
> due to a null pointer.
>
> Root cause is that strchr(cmd, '.') returns a null pointer when
> the input string does not contain
Commit 418396e212b59bf907dbccad997ff50f7eb61b16 introduced a
bug that causes nand read and nand write to crash in strcmp
due to a null pointer.
Root cause is that strchr(cmd, '.') returns a null pointer when
the input string does not contain a '.'
The strcmp function does not check for null point
On Thu Jun 07, 2012 at 10:36:53AM -0600, Stephen Warren wrote:
> On 06/07/2012 01:15 AM, Sughosh Ganu wrote:
> > On Wed Jun 06, 2012 at 10:44:59AM -0600, Stephen Warren wrote:
> >> On 06/05/2012 03:20 PM, Allen Martin wrote:
> >
> >
> >
> >>> diff --git a/include/configs/tegra2-spl.h b/include/c
On Wed, Jun 06, 2012 at 07:02:45PM -0700, Stephen Warren wrote:
> On 06/06/2012 04:00 PM, Allen Martin wrote:
> > Yes, that's the intention. Although I do have plans down the road for
> > adding memory initialization to the SPL so I can use it for
> > boot/flashing when in recovery mode and there'
On 06/06/2012 10:16 PM, Xie Shaohui-B21989 wrote:
>> -Original Message-
>> From: Wood Scott-B07421
>> Sent: Thursday, June 07, 2012 2:19 AM
>> To: Xie Shaohui-B21989
>> Cc: Wood Scott-B07421; u-boot@lists.denx.de; Tabi Timur-B04825
>> Subject: Re: [U-Boot] [PATCH] powerpc/CoreNet: add tool
On 06/07/2012 01:15 AM, Sughosh Ganu wrote:
> On Wed Jun 06, 2012 at 10:44:59AM -0600, Stephen Warren wrote:
>> On 06/05/2012 03:20 PM, Allen Martin wrote:
>
>
>
>>> diff --git a/include/configs/tegra2-spl.h b/include/configs/tegra2-spl.h
>>
>>> + * published by the Free Software Foundation; eit
Albert,
On Thu, May 31, 2012 at 9:47 AM, Tom Warren wrote:
> Albert,
>
> Please pull u-boot-tegra/master into ARM master. Thanks!
Haven't seen a reply, so repinging you.
Thanks,
Tom
>
> The following changes since commit 2ca4a209a5b961ad1be8782c68dabe326d77dfaf:
> SRICHARAN R (1):
> OMA
Hi Albert,
On Tue, May 15, 2012 at 09:42:59PM +0200, Albert ARIBAUD wrote:
> >On Sun, Apr 29, 2012 at 10:19:41PM +0200, Luka Perkov wrote:
> >>On Thu, Apr 19, 2012 at 08:38:19AM +0200, Albert ARIBAUD wrote:
> >>>Not my main area of expertise here, but I am not sure how this plays
> >>>on Marvell n
Hi all,
On Sun, May 27, 2012 at 11:44:51PM +0200, Luka Perkov wrote:
> The kwboot program boots boards based on Marvell's Kirkwood platform
> via Xmodem over their integrated UART.
>
> Signed-off-by: Daniel Stodden
> Acked-by: Luka Perkov
> Tested-By: Holger Brunck
> Tested-By: David Purdy
>
Hi Eric,
On Wed, Jun 06, 2012 at 22:47:46, Eric Bénard wrote:
> Hi Prabhakar,
>
> Le Fri, 1 Jun 2012 19:04:37 +0530,
> Prabhakar Lad a écrit :
>
> > From: Rajashekhara, Sudhakar
> >
> > On DA850/OMAP-L138 it was observed that in RMII mode,
> > auto negotiation was not performed. This patch en
From: Rajashekhara, Sudhakar
On DA850/OMAP-L138 it was observed that in RMII mode,
auto negotiation was not performed. This patch enables
auto negotiation in RMII mode. Without this patch, EMAC
initialization takes more time and sometimes tftp fails
in RMII mode.
Signed-off-by: Rajashekhara, Sud
From: Thomas Herzmann
On kmcoge5un unfortunately the HW wiring is differently to
other km arm boards.
Signed-off-by: Thomas Herzmann
Signed-off-by: Holger Brunck
---
board/keymile/km_arm/km_arm.c |4
1 files changed, 4 insertions(+), 0 deletions(-)
diff --git a/board/keymile/km_arm/
From: Holger Brunck
The additional headerfile is unneeded here, we can use the generic
km_kirkwood.h instead. And we can use the better config option
KM_PIGGY4_88E6061 for the specific features for boards with this
design in km_arm.c.
Signed-off-by: Holger Brunck
Signed-off-by: Valentin Longcha
These functions tried to access two static tables before relocation
(board_early_init_f is executed before relocation). But these static
tables lie in the bss section which is not valid before relocation.
These accesses then overwrote some parts of u-boot binary before it was
relocated. For the kmn
From: Holger Brunck
Use the generic header km_kirkwood.h and get rid of the
board specific header.
Signed-off-by: Holger Brunck
Signed-off-by: Valentin Longchamp
cc: Gerlando Falauto
cc: Prafulla Wadaskar
---
board/keymile/km_arm/km_arm.c |9 ++--
boards.cfg|2 +-
From: Thomas Herzmann
Add a function to read the dip_switch on kmcoge5un. If the
switch is set the actual_bank is set to 0 and this SW is
booted.
Signed-off-by: Thomas Herzmann
Signed-off-by: Holger Brunck
---
board/keymile/km_arm/km_arm.c | 14 +-
include/configs/km_kirkwood.h
The configuration EEPROM should be removed for P1B.
Signed-off-by: Valentin Longchamp
---
board/keymile/km_arm/km_arm.c | 11 +--
board/keymile/km_arm/managed_switch.c |3 ++-
board/keymile/km_arm/managed_switch.h |7 +++
3 files changed, 14 insertions(+), 7 deletio
From: Holger Brunck
For u-boot this board is similar to mgcoge3un. But some differences
are present. We have a different SDRAM on it and therefore a new
SDRAM config file. Additionaly this board has a direct MAC/MAC
connection from the kirkwood to a marvell simple switch without a
phy inbetween,
The PCIe FPGAs now have to support 2 resets: one for the non traffic
affecting part (PCIe) and one for the traffic affecting part.
When the FPGA is not reconfigured, we only reset the PCIe part.
Signed-off-by: Valentin Longchamp
---
board/keymile/km_arm/fpga_config.c | 13 +
1 fil
Some very similar #defines for reg addresses are used in a later patch
(managed_switch support for km_arm).
Signed-off-by: Valentin Longchamp
cc: Holger Brunck
cc: Prafulla Wadaskar
---
board/keymile/km_arm/km_arm.c | 22 +++---
1 files changed, 11 insertions(+), 11 deletions
In order to be able to perform board resets without interrupting the
traffic, the configuration of an already properly configured FPGA is
skipped.
This is because some PCIe FPGAs embed some other function that must
continue to work over reset.
It is then the responsibility of the application to t
From: Holger Brunck
Now we toggle between SPI and NAND flash automatically if
we claim the SPI bus. So we can get rid of this command.
Signed-off-by: Holger Brunck
Signed-off-by: Valentin Longchamp
cc: Prafulla Wadaskar
---
board/keymile/km_arm/km_arm.c | 26 --
inc
This adds a first support of the FPGA download for a PCIe FPGA based
on the BOCO2 CPLD.
This takes place in 3 steps, all done accessing the SPICTRL reg of the
BOCO2:
1) start the FPGA config with an access to the FPGA_PROG bit
2) later in the boot sequence, wait for the FPGA_DONE bit to toggle to
This can be used if we do not want to use an EEPROM for the
configuration.
Signed-off-by: Valentin Longchamp
---
board/keymile/common/common.h |7 --
board/keymile/km_arm/managed_switch.c | 169 +++--
board/keymile/km_arm/managed_switch.h | 99 +
From: Holger Brunck
Remove config options from boards.cfg and simply add one switch
per board and differ afterwards in km_kirkwood.h between the features.
More boards are upcoming and therefore it's easier to have this
at one place.
Signed-off-by: Holger Brunck
Signed-off-by: Valentin Longchamp
From: Holger Brunck
This board is similar to portl2, but it has the u-boot environment
in a SPI NOR flash and not in an i2c eeprom like portl2 have.
Some other details:
- IVM EEPROM is at adress: pca9547:70:9
- PCI is enabled
- PIGGY4 is connected via MV88E6352 simple switch. There is no phy
They are needed on all km_arm boards where we have the environement
variables in the NOR Flash. First boards using this feature are
kmcoge5un and kmnusa.
Signed-off-by: Valentin Longchamp
Signed-off-by: Holger Brunck
cc: Gerlando Falauto
cc: Prafulla Wadaskar
---
board/keymile/km_arm/km_arm.c
This is achieved thanks to the support read/write regs for the external
88e6352 switch. The functions for this are added into an own file
managed_switch.c. This is compiled if the define CONFIG_KM_MANAGED_SW_ADDR
was set in the board setup. This define specifies the phy address.
Signed-off-by: Val
So that they can be redefined by some boards specific values.
Signed-off-by: Valentin Longchamp
Signed-off-by: Holger Brunck
cc: Gerlando Falauto
cc: Prafulla Wadaskar
---
arch/arm/include/asm/arch-kirkwood/config.h | 12 +---
1 files changed, 9 insertions(+), 3 deletions(-)
diff -
This is required for all our keymile ARM boards. The selected MPPs are
the default one for the SPI controller, thus the 0x0 definition.
Signed-off-by: Valentin Longchamp
cc: Holger Brunck
cc: Prafulla Wadaskar
---
include/configs/km/km_arm.h |3 +++
1 files changed, 3 insertions(+), 0 dele
This used to be done with registers direct access, which is not clear
and optimal.
Signed-off-by: Valentin Longchamp
Signed-off-by: Holger Brunck
cc: Gerlando Falauto
cc: Prafulla Wadaskar
---
board/keymile/km_arm/km_arm.c | 53 +---
include/configs/km/km
This series adds support for 2 new Kirkwood boards at Keymile: kmnusa and
kmcoge5un. All the previously supported boards that had a proper config file
now are all supported by the generic km_kirkwood.h config file.
This series also adds support for the environment variables in the SPI NOR
Flash, f
From: Lad, Prabhakar
This patch adds support for direct NOR boot mode on
da850/omap-l138. added da850evm_direct_nor entry in
boards.cfg to allow to build targets.
Signed-off-by: Lad, Prabhakar
Signed-off-by: Rajashekhara, Sudhakar
Signed-off-by: Hadli, Manjunath
---
Changes for v2:
1: Added
From: Lad, Prabhakar
This patch adds support for NAND SPL on DA850/OMAP-L138.
Signed-off-by: Lad, Prabhakar
Signed-off-by: Rajashekhara, Sudhakar
Signed-off-by: Hadli, Manjunath
---
Changes for v2:
1:Added a check to perform initializations of serial
console only if CONFIG_SPL_LIBCOMMON_
From: Lad, Prabhakar
Though Commit id a3f88293ddd13facd734769c1664d35ab4ed681f (da850evm:
setup the NAND flash timings) has configured the AEMIF timings, they
are not exactly in sync with the timings used in Linux. Linux is
configuring the timing register as 0x0804, where as currently it
conf
From: Rajashekhara, Sudhakar
On Logic PD Rev.3 DA850/OMAP-L138 EVM, NOR and MMC/SD cannot
work together. This patch enables the MMC/SD support only
when NOR support is disabled. NOR Flash identification works
even without this patch, but erase and write will have issues.
Signed-off-by: Rajashekh
From: Lad, Prabhakar
DA850/OMAP-L138 does not support strict MMC/SD boot mode. SPL will
be in SPI flash and U-Boot image will be in MMC/SD card. SPL will
do the low level initialization and then loads the u-boot image
from MMC/SD card.
Define the CONFIG_SPL_MMC_LOAD macro in the DA850/OMAP-L138
From: Rajashekhara, Sudhakar
AHCLKR/UART1_RTS/GP0[11] pin needs to be configured for
MMC and NOR to work on DA850/OMAP-L138 Rev.3 EVM. When
GP0[11] is low, the SD0 interface will not work, but NOR
flash will. When GP0[11] is high, SD0 will work but NOR
flash will not.
Signed-off-by: Rajashekhara
From: Lad, Prabhakar
This patch adds support for MMC/SD on DA850/OMAP-L138.
Signed-off-by: Lad, Prabhakar
Signed-off-by: Rajashekhara, Sudhakar
Signed-off-by: Hadli, Manjunath
---
Changes for v2:
1:Removed CONFIG_MMC_MBLOCK config which was never used.
2:Added comment while enabling MMC co
From: Lad, Prabhakar
This series adds MMC/SD, NAND and NOR SPL support
for Logic PD's DA850/OMAP-L138 EVM. This series
also fixes some issues found on the EVM during
testing. The patches are sent in a series as these
patches need to be applied in the order they are sent.
Changes for v2:
1: Fixed
Hi Prafulla,
On 06/05/2012 04:21 PM, Prafulla Wadaskar wrote:
>> -Original Message-
>> From: Valentin Longchamp [mailto:valentin.longch...@keymile.com]
>> Sent: 01 June 2012 17:01
>> To: Prafulla Wadaskar
>> Cc: u-boot@lists.denx.de; Valentin Longchamp; Holger Brunck
>> Subject: [PATCH v4
Dear Zang Roy-R61911,
The patch "[PATCH V2] MPC8xxx: Define cache ops for USB" wasn't applied yet for
some reason. It fixes the issue.
> Hi, Marek
>
> When I build P5020DS_config with the current u-boot head, I got:
> /home/roy/CVS/upstream/u-boot/drivers/usb/host/ehci-hcd.c:346: undefined
> re
On Wed Jun 06, 2012 at 10:44:59AM -0600, Stephen Warren wrote:
> On 06/05/2012 03:20 PM, Allen Martin wrote:
> > diff --git a/include/configs/tegra2-spl.h b/include/configs/tegra2-spl.h
>
> > + * published by the Free Software Foundation; either version 2 of
> > + * the License, or (at your opt
60 matches
Mail list logo
