s to be attached to a
single parallel port.) If the switch is in the wrong position scanimage
can't detect the scanner, but the switch is in the correct position.
Any other suggestions?
TIA
--
# Mertens Bram "M8ram"Linux User #249103 #
# Red Hat Linux 7.3 KDE 3.0.0-10 ker
On Thu, 2002-11-28 at 17:13, Mertens Bram wrote:
> On Thu, 2002-11-28 at 17:00, Jochen Eisinger wrote:
> > hum, i nearly forgot.. you're using a 600dpi scanner, there's a special
> > option for this in the config file. use600 (see the man-page)
> >
> > do yo
d/mustek_pp.conf...
Do I simply add this line to the end of the file?
The section
# Use this option for 600 dpi scanners
# for example ScanExpress 1200 ED Plus
#option use600
I found this paragraph in the man page but it is nowhere in my
/etc/sane.d/mustek_pp.conf...
TIA
--
# Mertens Br
26 17:45 test.pnm
So the file seems to be ok, only the info that gets written to it seems
to be replaced by a blank image...
Thanks
--
# Mertens Bram "M8ram"Linux User #249103 #
# Red Hat Linux 7.3 KDE 3.0.0-10 kernel 2.4.18-3 i686 128MB RAM #
# 5:47pm up 6 days, 6:37, 3 users, load average: 0.58, 0.40, 0.23 #
On Tue, 2002-11-26 at 13:53, Mertens Bram wrote:
> I always test using the "acquire preview" that wouldn't make a
> difference would it?
Well it seems to make a lot of difference!
I've tried to scan twice without the acquire preview but using the start
scan button fro
r helping me, any other suggestions?
I always test using the "acquire preview" that wouldn't make a
difference would it?
--
# Mertens Bram "M8ram"Linux User #249103 #
# Red Hat Linux 7.3 KDE 3.0.0-10 kernel 2.4.18-3 i686 128MB RAM #
# 1:50pm up 6 days, 2:40, 3 users, load average: 1.34, 1.23, 1.05 #
0
[mustek_pp] motor_controll_1015: control code 0xc3
[mustek_pp] config_ccd: 300 dpi, mode 2, invert 0, size 2600
[mustek_pp] set_dpi_value: value 0x21
[mustek_pp] set_line_adjust: ppl 2600 (2600), adjust 2600, skip 22
[mustek_pp] close: device closed
[mustek_pp] exit: (...)
[root@localhost M8ram]#
On Sun, 2002-11-24 at 18:39, Henning Meier-Geinitz wrote:
> On Sun, Nov 24, 2002 at 05:59:03PM +0100, Mertens Bram wrote:
> > I have configured xsane but I am at the moment unable to run it as
> > normal user.
>
> You mean that your scanner is not detected if you run x
sgo -> sg14
lrwxrwxrwx1 root root4 Jul 3 16:05 sgp -> sg15
[root@localhost sane.d]# scanimage --list-devices
device `mustek_pp:MD9848' is a Medion MFS-600IIIP flatbed scanner
TIA
--
# Mertens Bram "M8ram"Linux User #249103 #
# Red Hat Linux 7.3 KDE 3.0.0-
shows a blank page.
When I actually tried to scan an image xsane terminated with the
following message:
[root@localhost sane.d]# xsane
Floating point exception
Trying again the resulting image was again, completely blank.
Do I have to restart anything? Are there any other settings I must
alter?
10 matches
Mail list logo
