On Aug 11, 2012, at 6:43 AM, Drake wrote:
> Ray,
>
> If golf cart batteries can't surge over 2000 amps, then it would seem that
> the fuse in line with the QO can be deleted in some cases. Is the 2000 A
> surge for one 6 volt battery or 2 in series?
Current stays the same, just voltage chang
Ray,
If golf cart batteries can't surge over 2000 amps, then it would seem
that the fuse in line with the QO can be deleted in some cases. Is
the 2000 A surge for one 6 volt battery or 2 in series?
Fuses can be put in the QO enclosure ahead of the loads and DC rated
Class T fuses can be bol
I just returned from northern BC Canada, wiring wooden wall tent platforms
for lights. I searched all over the NEC for rules regarding wiring tents,
and couldn't find a single reference! Go figure.
The tents are spread out away from the power center, so it's 120vac from a
1kW Magnum MME inverter (
Sounds like a good opportunity to recycle (loose) old hand me over equipment. Dan BrownFoxfire Energy Corp.Renewable Energy Systems(802)-483-2564www.Foxfire-Energy.comNABCEP #092907-44
Original Message
Subject: Re: [RE-wrenches] 12V loads
From: R Ray Walters <r...@solarray.
The only way I deal with hunting lodges and the like is to install close to
full code (I do relax on the exact year, since it isn't new construction), or I
supply parts and advice, and let them do it themselves.
In Taos, we had some pretty poor folks trying to make it out in the desert, so
I alm
The "code compliance" part has been my worry. The small DC system seems to be
full of code problems. I do see the benefit of the DC only for the fish houses,
but the hunting shacks make me always think code. I have used the morningstar
300W for a few applications and have a magnum 1000W in my
The QO breaker has an AIC of 5000 amps. The usual golf cart batteries have a
short circuit current of about 2000 amps, so you could do a set of 4 golf cart
batteries at 12v, without worrying about the extra fuse.
Once again, if the system gets any bigger, they should just go to an inverter
base
Good point Ray. I work on lots of low budget micro remote systems
too.decent ATC fuse blocks are avaiIable (though I avoid Autozone etc)
and you can mount 'em in a gray metal box to look code-ish Have done marine
disco (big red switch) and class t fuse in some tiny systems for inverter
-- the M
I second using QO load centers. You will want to put a fuse, like an
FRN-R, between the battery and the load center, as the QO breakers
don't have a high AIC rating. 12 V systems can be wired as easily as
a regular AC system.
At 05:05 PM 8/9/2012, you wrote:
Hello,
I've been looking at a l
The problem with many of the suggestions, is that these Micro 12 v systems
generally have budgets under $1000 parts. 20% of the budget allocated to
breakers and discos isn't reasonable, same with a Trimetric.
The ATC fuses are used for literally billions of 12 v circuits that all of you
use e
Great ideas. I think for this job I will use the combiner box idea. I do have
an old trace disconnect box as mentioned laying around that would work as well.
Since I'm only putting in a couple DC lights, the combiner method should work
great. I get a lot of fish house and hunting shack inquire
On the cheap side, Square D QO. They are indeed rated to 48VDC, which means
you can use them with a 24v system (but NOT a 48v system). If there is an
inverter too, the Midnite mini-panel ($160 with main breaker) and DIN-rail
DC breakers.
Dan Fink,
Executive Director;
Otherpower
Buckville Energy Co
I like the Midnite MNDC series.low
cost, with lots of room for future expansion.
List price around $225
I like Maverick's suggestion of using a combiner box, even lower
cost.
Roy Butler
NABCEP Certified Small Wind Installer®
NABCEP Certified Solar
I'd try using one of midnite's many boxes
Jay
Peltz power
Sent from my iPhone
On Aug 10, 2012, at 6:55 AM, Jason Szumlanski wrote:
> I'm not sure about the price, but what about using the DC enclosure from an
> Outback Flexware system? Lots of space for branch circuit breakers, plus a
> big
I'm not sure about the price, but what about using the DC enclosure from an
Outback Flexware system? Lots of space for branch circuit breakers, plus a
big DC disconnect.
Jason Szumlanski
Fafco Solar
On Thu, Aug 9, 2012 at 5:05 PM, Jesse Dahl wrote:
> Hello,
>
> I've been looking at a lot of h
I've seen lots of folks use old Trace DC Boxes. I try to set up some kind of low battery disco if it's just DC.Dan BrownFoxfire Energy Corp.Renewable Energy Systems(802)-483-2564www.Foxfire-Energy.comNABCEP #092907-44
Original Message
Subject: Re: [RE-wrenches] 12V
Actually if you want to really keep the price down, you can use a 12 v ATC fuse
block from Del City wire.
I only use it for RVs, autos, and temporary structures (like fish houses).
12 vdc has its place in Micro systems, but it quickly becomes ridiculous, as
soon as you want more than a couple
Thats what I was looking at. Cost wise, if you were to get crazy with
panelboards and stuff the price just skyrockets.
Thanks eh!
Jesse
Sent from my iPhone
On Aug 9, 2012, at 4:40 PM, "Maverick Brown [Maverick Solar]"
wrote:
> We use solar combiner boxes. For instance, the first breaker
We use solar combiner boxes. For instance, the first breaker is actually a 63A
for the "Main" and then you could have load breakers for each circuit.
Thank you,
Maverick
Maverick Brown
BSEET, NABCEP Certified Solar PV Installer ®
President & CEO
Maverick Solar Enterprises, Inc.
Office: 5
Square D QO is listed to 24V DC according to some of their literature.
Matt
Matthew Partymiller
Solar Energy Solutions LLC
(859) 312-7456
m...@solar-energy-solutions.com
> Hello,
>
> I've been looking at a lot of hunting shacks, fish houses and other 12V
> loads setups and was wondering how peop
20 matches
Mail list logo
