-boun...@lists.re-wrenches.org]on Behalf Of benn kilburn
Sent: Wednesday, October 20, 2010 5:18 PM
To: Wrenches
Subject: Re: [RE-wrenches] Mounting Enphase when using S-5-PV Clamps
Not a lot of you guys in the field today 'eh? I was just checking a spec
on my laptop and noticed i had
.@daystarsolar.ca780-906-7807 HAVE A SUNNY DAY
Date: Wed, 20 Oct 2010 12:34:56 -0600
From: al...@positiveenergysolar.com
To: re-wrenches@lists.re-wrenches.org
Subject: Re: [RE-wrenches] Mounting Enphase when using S-5-PV Clamps
We have used these for years. They work bette
We have used these for years. They work better than wire ties, but
the rubber liner deteriorates over time, so install them as if there
is no rubber protection on the loom clamp.
Allan Sindelar
Allan@positiveenergysolar.com
If this helps,
I just installed a system and used 3 different size loop clamps ( del city)
which worked really well.
I used 3/8" for single wires, 3/4 for 2 wires and 1" for 3 and also for the
connector, worked really well, made it all very clean.
I attached them with SS tek screws into the rai
.
_
From: re-wrenches-boun...@lists.re-wrenches.org
[mailto:re-wrenches-boun...@lists.re-wrenches.org] On Behalf Of
toddc...@finestplanet.com
Sent: Wednesday, October 20, 2010 10:23 AM
To: RE-wrenches
Subject: Re: [RE-wrenches] Mounting Enphase when using S-5-PV Clamps
I have the
CA 94953
Cell: 707-321-2937
Office: 707-789-9537
Fax:707-769-9037
From: benn kilburn
To: Wrenches
Sent: Wed, October 20, 2010 8:06:33 AM
Subject: [RE-wrenches] Mounting Enphase when using S-5-PV Clamps
Mornin,
I'm looking at mounting an Enphase M190 s
I have the same question, only regarding pole mounts.
Todd
On Wednesday, October 20, 2010 8:06am, "benn kilburn"
said:
Mornin,
I'm looking at mounting an Enphase M190 system on a standing seam metal roof
and was considering using the S-5-PV clamps (as opposed to just the S-5's and
L-feet),
Benn:
I just designed one of these systems yesterday. It is for an electrical
engineer, so I thought carefully about this project.
If you mount your modules directly to the S-5 clips, you need to install
modules in landscape orientation. If you have two columns, you can place
them in mirro
ts.re-wrenches.org
Date: Wed, 20 Oct 2010 08:39:13 -0700
Subject: Re: [RE-wrenches] Mounting Enphase when using S-5-PV Clamps
Benn,
If it were me, I would mount rails on the S-5! Clamps so that
you can mount the micro-inverters on the rails. It is not good to mount the
inverters on the m
-wrenches.org] On Behalf Of benn kilburn
Sent: Wednesday, October 20, 2010 8:07 AM
To: Wrenches
Subject: [RE-wrenches] Mounting Enphase when using S-5-PV Clamps
Mornin,
I'm looking at mounting an Enphase M190 system on a standing seam metal roof
and was considering using the S-5-PV clamp
Mornin,
I'm looking at mounting an Enphase M190 system on a standing seam metal roof
and was considering using the S-5-PV clamps (as opposed to just the S-5's and
L-feet), which do not use any mounting rails. No rails means no where to
properly mount the M190's!?!It was suggested to mount the
11 matches
Mail list logo
