HI Randy,
Go to http://www.righthandeng.com/
They got them.
jay
peltz power
On Jul 16, 2009, at 8:44 PM, Randy Brooks wrote:
Wrenches,
A while back I recall hearing about an after market add on to
provide non-volatile memory for Trace inverter settings. I haven't
been able to locate suc
HI all,
I've got a different issue here with FM interference.
I replaced an old Trace DR with a Magnum 4024 pure sine wave.
The radio in question, or location is within 15' from the inverter.
The interference is there on a portable FM unit as well.
There is no interference with just the generato
Wrenches,
A while back I recall hearing about an after market add on to provide
non-volatile memory for Trace inverter settings. I haven't been able
to locate such a product. Anyone know of one, or have experience
with one?
Also, a customer with one SW4024 inverter is interested in addi
I see that this install is using EMT, are you using a bonding bushings on
the EMT? If so, I had interference on a large PV powered refrigeration unit
that used an electronic expansion valve. The wires were installed inside EMT
causing all kinds of weird problems. When I removed bonding at both en
Excellent article that sums it all up.
The one thing I would add is that ferrite filters don't actively "do"
anything - they just act like a high resistance to EMI/RFI and swamp it out,
so you can put as many as you want, anywhere, and it won't hurt anything
(but it may also not do anything) -
Excellent Dan! The first thing I would do in most cases is your #5.
Increasing the RF signal to the receiver will usually overcome the
relatively low level RFI. As an amateur operator (KB5HMU) I sometimes
have to deal with close RFI at 160 meters, 1.8 to 2kHz. I have a
tunable dipole with p
Interference from inverters will always be an issue. It's a difficult topic
for many to understand .. and equally difficult to reduce. Note you can reduce
.. but not eliminate the interference.
To complicate things, the farther a radio is from the transmitter, the more
difficult this issue w
Allan,
I have two different systems using these EU6500 generators but instead of
the Trace they have a Magnum MS 4024 and 4024AE. Both work flawlessly as
long as the eco-throttle is off.
Good luck!
Mark Dickson
Oasis Montana Inc.
_
From: re-wrenches-boun...@lists.re-wrenche
In some cases we have had good luck with Ferrite filters. But not always, and
not always easy to find the source of the noise.
..
Northern Arizona Wind & Sun - Electricity From The Sun Since 1979
Solar
Check out
http://www.williamsform.com/Ground_Anchors/Polyester_Resin_Rock_Anchors/polyester_resin_anchors.html
Found my solution for anchoring into rock. Hope this helps. Also check out
"micro-piles" in the downloadable catalog...Pole mounting?? They will do
the engineering
Contact - Rob We
Nik,
I have several customers who use your basic computer UPS. 100VA should be
plenty for a circulator and controller.
Kirk Herander
Vermont Solar Engineering
802.863.1202
NABCEP(tm) Certified Solar Installer
NYSERDA-eligible Installer
VT Solar Incentive Program Partner
_
Fro
Logan,
The SS generator seemed to be a hopeful option. I've tried
repeatedly to get pricing and warranty information, but as of yet,
this information has not been supplied. What is the deal?
Drake
At 10:40 AM 7/10/2009, you wrote:
Here is an 7Kw option that has proved itself all over Mont
Mike,
Following is an email that I received by our State office of Energy
Security. The link should get you the information that you are looking for.
Hello all:
Interstate Renewable Energy Council (IREC) and Solar Electric Power
Association (SEPA) hosted a one hour Federal Solar Tax Cr
Folks,
Anyone have experience with a small backup power system specifically for a
solar hot water system?
Thanks in advance,
Nik
--
Nicholas Ponzio
Building Energy
1570 South Brownell Road
Williston, VT 05495
t: 802-859-3384 x15
f: 802-658-3982
www.BuildingEnergyVT.com
"Building Solutions for
14 matches
Mail list logo
