On 04/12/2015 15:58, Florian Eckert wrote:
> Hallo mailinglist,
>
> I have seen in the linux sources of the lantiq falcon soc, that there
> is some working done for nmi handling.
>
> I have an lantiq xrx200 board and want to use nmi handling to react on
> an power failure which is signaled over
From: Josh Bendavid
Add initial support for Archer C2600 to Makefiles and profiles. This is
sufficient to build a working factory image. Sysupgrade image is not
implemented yet. Currently wired network is working, but
LED's/buttons/wireless are not.
Signed-off-by: Josh Bendavid
---
diff --g
The PBR-M1 support in current OpenWrt is for the early demo board and it
doesn't work on the final board.This patch fixes the support for it.
The LED called pbr-m1:buzzer is a beeper connected to GPIO26 so I used
gpio-beeper instead of gpio-leds.
Changes since V2:
reorder the boards in /etc/diag
From: Josh Bendavid
Add support for Archer C2600 to tplink-safeloader by adding needed
partition table, and vendor information plus support list strings.
Additional string C2600 is enabled for the -B option.
Signed-off-by: Josh Bendavid
---
diff --git a/tools/firmware-utils/src/tplink-safeload
Starting with r47755 the pppoe wan interface section isn't any longer added to
the network config on firstboot, using the default configuration. Since the
commit message does not mention such a change, I assume that this wasn't
intentionally.
Signed-off-by: Mathias Kresin
---
target/linux/lantiq
Ping.
Any comments? what to do about ath79_setup_ar934x_eth_rx_delay.
Leave it as is, or get rid of it?
Regards,
Christian
On Friday, November 27, 2015 08:34:40 PM Christian Lamparter wrote:
> On Saturday, November 21, 2015 08:45:23 PM John Crispin wrote:
> > Hi,
> >
> > sorry to jump in this
Hi,
On Fri, Dec 4, 2015 at 12:40 AM, Nikolay Martynov wrote:
> Current way of compuling dts files involves calling C preprocessor on
> main dts file only. This means that dtsi includes cannot have C-style
> includes.
Why not? Shouldn't they get processed as well as long as they are
included wit
Signed-off-by: Mathias Kresin
---
Tested by my self with a "normal" VDSL2 line and by a user with a german 1&1
VDSL2 vectoring line:
/etc/init.d/dsl_control status
ATU-C Vendor ID: B5,00,42,44,43,4D,A4,61
ATU-C System Vendor ID: B5,00,42,44,43,4D,00,00
Dynamic Spectrum Management is a precondition for G.993.5 (VDSL2 vectoring).
Signed-off-by: Mathias Kresin
---
It has been sucessfully tested by a user with a german 1&1 VDSL2 vectoring line,
who could only get the ADSL2+ fallback speed[1] without this patch (regardless
of vectoring support in f
Hallo mailinglist,
I have seen in the linux sources of the lantiq falcon soc, that there
is some working done for nmi handling.
I have an lantiq xrx200 board and want to use nmi handling to react on
an power failure which is signaled over the nmi gpio.
I have seen filesystem errors if it is not c
Hello,
See inline, below.
Cheers,
Piotr
2015-12-04 14:50 GMT+01:00 GuoGuo :
> The PBR-M1 support in current OpenWrt is for the early demo board and it
> doesn't work on the final board.This patch fixes the support for it.
> The LED called pbr-m1:buzzer is a beeper connected to GPIO26 so I used
Hello!
2015-12-03 20:08 GMT+08:00 Sebastian Careba :
> The board is based on mt7621AT cpu, and has 16mb nor flash, 256mb of ram, 2
> sata ports, microsd card slot, 1 USB 3.0 port and at least one 2.4 and one 5
> ghz antenna.
I think you forgot to enable the XHCI support in the dts file.
> This i
In-line;
On 3 December 2015 at 20:50, Ben Whitten wrote:
> This patch adds a uboot package for at91 and honours COPTS.
> If the SPL binary is generated for the specified board it moves that too.
>
> Signed-off-by: Ben Whitten
> ---
> package/boot/uboot-at91/Makefile | 111
> +++
The PBR-M1 support in current OpenWrt is for the early demo board and it
doesn't work on the final board.This patch fixes the support for it.
The LED called pbr-m1:buzzer is a beeper connected to GPIO26 so I used
gpio-beeper instead of gpio-leds.
Changes since V1:
Fix style problems.
Use pbr-m1:
Hi,
upgrading to latest openwrt trunk broke PPPoE connectivity with fsl-gianfar
Ethernet driver for me.
Reason is the fsl-gianfar driver changed its behavior regarding link state
notifications:
linux 3.10:
[ 1471.142926] libphy: mdio@ffe24000:09 - Link is Up - 1000/Full
ip monitor:
15:43:53.02
15 matches
Mail list logo
