Re: [Openocd-development] [PATCH] Add ft2232_index command

I's think serial numbers would suffice, and be much more usable/stable. ___ Openocd-development mailing list Openocd-development@lists.berlios.de https://lists.berlios.de/mailman/listinfo/openocd-development

[Openocd-development] [PATCH] Add ft2232_index command

Attached patch introduces ft2232_index command that allows to set specific FT2232 device if there are several of them in the system. Comes handy when you have two JTAG adapters or JTAG adapter and USB/serial post converter ft2232_index.patch Description: Binary data _

[Openocd-development] Problems with LPC2148 persists also with Wiggler clone

Hi there. I still have not been able to connect properly to my Olimex LPC-H2148 prototype board. After my first mail thread I could connect the olimex-arm-usb-tiny-h adapter by adding -c "jtag_khz 1000" to the command line. I have lately also discovered that this also works with the openocd 0.4.0

[Openocd-development] [PATCH] cfg: add omapl138 support and da850evm preliminary support

This patch adds support for the omapl138 target and preliminary support for the da850evm. The target cfg file is based on the icepick routing done by the target/ti_dm6446.cfg file. I have performed limited testing with this setup. I am posting this patch in the interest of sharing cfg files and

Re: [Openocd-development] avi_v5_swd.c implementation

How this patch is implemented is not important. But some information will be helpful, I think. For example: I find that after dap_to_swd sequence, some idles bits should be added. Maybe it will be a method to try if a lot of "CTRL/STAT error" are received. 2010/8/10 simon qian > This patch is

Re: [Openocd-development] avi_v5_swd.c implementation

This patch is not for comming to openocd. I just publish the patch for testing Versaloon driver, especially SWD driver. All code is intended to be just simple, and working(hope it's working). APACC/DPACC for JTAG is a register. But for SWD, it's only a bit in the request part (5.3.1 section of AD

Re: [Openocd-development] avi_v5_swd.c implementation

One way you can tell this is very wrong is that it references JTAG-specific registers APACC/DPACC ... those concepts don't even exist with SWD. ___ Openocd-development mailing list Openocd-development@lists.berlios.de https://lists.berlios.de/mailman/li

Re: [Openocd-development] Warn : Timeout (1000ms) wai ting for ACK=OK/FAULT in JTAG-DP

Hello I'm using the LM3SB92 with the same error. The LM3S1958 works fine. Could anyone help us? I'm using the openocd-0.4.0. Thanks Spin ___ Openocd-development mailing list Openocd-development@lists.berlios.de https://lists.berlios.de/mailman/listin

[Openocd-development] avi_v5_swd.c implementation

Attachment is the adi_v5_swd.c and arm_adi_v5.c code for my recent SWD patch for OpenOCD. Code is almost similar as adi_v5_jtag.c but with some fix for SWD. 1. original dap_to_swd is not stable. I change the last 4 bits of jtag2swd_bitseq from '1' to '0', the 4 bits act as idle bits. 2. after dap_

Re: [Openocd-development] Clarifying deassert reset + fixing reset run + halt

Merged. -- Øyvind Harboe US toll free 1-866-980-3434 / International +47 51 63 25 00 http://www.zylin.com/zy1000.html ARM7 ARM9 ARM11 XScale Cortex JTAG debugger and flash programmer ___ Openocd-development mailing list Openocd-development@lists.berlios

Re: [Openocd-development] disable polling when polling fails

Merged. -- Øyvind Harboe US toll free 1-866-980-3434 / International +47 51 63 25 00 http://www.zylin.com/zy1000.html ARM7 ARM9 ARM11 XScale Cortex JTAG debugger and flash programmer ___ Openocd-development mailing list Openocd-development@lists.berl