On Wed, Jun 17, 2015 at 4:48 AM, Jérémie Courrèges-Anglas
wrote:
> Stefan Sperling writes:
>
> > On Wed, Jun 17, 2015 at 12:47:57PM +0200, Jérémie Courrèges-Anglas
wrote:
> >> IIUC BCM43* nics could have been supported if development efforts hadn't
> >> been killed by licensing issues. I
On Thu, Jan 15, 2015 at 9:27 AM, Jon Simola wrote:
>
> You could try looking for a KVM over IP that supports VNC.
>
To explain better, this would be in a private /30 network just so you can
VNC from laptop to the KVM.
--
Jon
On Thu, Jan 15, 2015 at 8:38 AM, Alan McKay wrote:
> Hey folks,
>
> I'm looking for something like this that I can plug into a network
> debugging laptop to get console access to servers in a rack. Ideally
> the laptop would run OpenBSD or in a pinch Linux.
You could try looking for a KVM over
On Mon, Dec 20, 2010 at 3:20 PM, brett wrote:
> r...@beagleboard:~# route add default gw 192.168.10.12 netmask 255.255.255.0
dev
> usb0
Don't set a netmask on your default route. You're adding a route for
0.0.0.0/24.
> r...@beagleboard:~# route
> Kernel IP routing table
> Destination Gatew
On Thu, Dec 17, 2009 at 9:31 AM, Mauro Rezzonico wrote:
> Joakim Aronius wrote:
>
>> I added a big disk over USB which I use for
>> backup (mounted on /backup).
>
> Well don't do that!
>
> Mount under /usr/backup, or /var/backup, or /tmp/backup or whatever!
And/Or wrap the backup script with some
On Thu, Sep 10, 2009 at 10:46 AM, Marco Peereboom wrote:
> I would love to get my hands on such a drive :-)
>
> EMC uses the same magic; they cram stuff in the additional 8 bytes.
I inherited a couple of shelves from an old EMC setup, and ended up
using Seagate's SeaTools Enterprise Edition to re
On Tue, Feb 3, 2009 at 3:56 PM, Vivek Ayer wrote:
> Since I'm in control of a public IP, I'm supposed to set the netmask
> for the ext_if on my openbsd router to 255.255.0.0 not 255.255.255.0.
> Would that solve the mysterious ping problem?
Actually a not-mysterious routing problem.
The entity
On Fri, Aug 8, 2008 at 2:17 AM, clifford bailey
<[EMAIL PROTECTED]> wrote:
> Finally my ospf config:
> hello-interval 1
> router-dead-time 2
Those timings might be a little agressive for VMs to handle, as
missing a single hello
could cause all sorts of excitement with the default SPF timer value
On 7/30/08, Khalid Schofield <[EMAIL PROTECTED]> wrote:
> Any luck with QLA2200's and OpenBSD?
I ran one as an experiment for a while, using an old EMC shelf full of
36GB drives.
Similar story, trying to boot with the array attached would stop while trying to
probe the drives. Had to use the Seag
On 4/18/08, ropers <[EMAIL PROTECTED]> wrote:
> Sometimes I find myself in need of a disk checking utility that can
> check both disks with known *and unknown* filesystems, and/or that can
> check even currently unpartitioned space on a disk.
Not claiming to be an optimal solution (dd is faster)
On 10/3/07, [EMAIL PROTECTED] <[EMAIL PROTECTED]> wrote:
> I'm trying to set up an OpenBSD (4.2 snapshot) router as a VRRP
> neighbor to a Juniper M7i (JunOS version 7.5R2).
<...>
> Does anyone know if there's a tweakable option to fix this, or
> if it's even possible to do this at all (is CARP co
On 9/7/07, Tom Bombadil <[EMAIL PROTECTED]> wrote:
> But is there any way to get a list of all files in the filesystem
> without using 'find'?
tar cvfX /dev/null /mnt > filelist.txt
or perhaps
ls -R /mnt
mtree(8) might also be useful, depending on what you're trying to accomplish.
But the best
On 6/13/07, David Newman <[EMAIL PROTECTED]> wrote:
In the example given here:
http://www.openbsd.org/faq/pf/carp.html
Each physical interface has two IPv4 addresses, one for a shared IP and
one for the interface address. That would require a /29 or shorter to
accommodate these two addresses,
On 5/17/07, Peter Hessler <[EMAIL PROTECTED]> wrote:
Its not just starting with a dash, I also cannot open ones that end the
host section with a dash (ke-.deviantart.com)
On 2007 May 17 (Thu) at 10:46:01 -0700 (-0700), Brian wrote:
:I am trying to open up this url with firefox on openbsd -curren
On 4/23/07, Paul Pruett <[EMAIL PROTECTED]> wrote:
Appears to be a low prices for a 16port capture card,
has anyone tried the ProVideo series with OpenBSD?
Not personally, I did play around with a bktr878 on a Hauppauge
something or other, it worked fine but I never was able to figure out
the
On 4/6/07, Stefan Sperling <[EMAIL PROTECTED]> wrote:
Yes they did: http://bcm-v4.sipsolutions.net/
I've spent some time reading it today, for the occasion.
It seems to be lacking some details, e.g. the section describing
how to attach the backplane bridge of the chip [1] says to turn on the
c
On 3/30/07, Jacob Yocom-Piatt <[EMAIL PROTECTED]> wrote:
NOTE: TAPE=/dev/nrst0 here so it doesn't rewind after tar-ing
That's your problem.
unset TAPE, or just use the default /dev/rst0 device.
(hysterical raisins and all)
--
Jon
On 3/26/07, Aaron Martinez <[EMAIL PROTECTED]> wrote:
My question is. I have OBSD 4.0 running on an Asus p3b-F with 6 pci
slots that i'm wanting to use as a router/firewall. I have 5 fxp
interfaces in the machine inserted starting from the bottom pci slot
up.
A second related question, in t
On 12/21/06, Michael <[EMAIL PROTECTED]> wrote:
> Got no serial cable available right now so I made some photos... :D
>
> http://wp1050733.wp078.webpack.hosteurope.de/hotplug/dsci1679.jpg
> http://wp1050733.wp078.webpack.hosteurope.de/hotplug/dsci1680.jpg
> http://wp1050733.wp078.webpack.hosteur
On 12/18/06, Karl R. Balsmeier <[EMAIL PROTECTED]> wrote:
Is there a specific way to set a name server so that clients are always
*forced* to use an autoritative name server?
Clients can not (or at least, should not) talk directly to
authoritative name servers. Clients make their DNS requests
On 11/30/06, L. V. Lammert <[EMAIL PROTECTED]> wrote:
seems like these 'SATA Backplanes' would be better space wise
Backplanes, in general, are something I really appreciate. Better
cooling and cabling, and quite good for storage density.
Spend time and the extra money getting a backplane wit
On 11/28/06, Daniel Ouellet <[EMAIL PROTECTED]> wrote:
Is there a reason why it's not possible to start spamd with example
spamd -c 1000
in /usr/src/libexec/spamd/spamd.c:
#define MAXCON 800
Not a big deal, but I just couldn't do this.
spamd(8) says the default is 800, which is actually a
On 11/9/06, Constantine A. Murenin <[EMAIL PROTECTED]> wrote:
On 09/11/06, Eric Huiban <[EMAIL PROTECTED]> wrote:
> >> has anyone advise to find cheap sensors (temperature, but also humdity,
> >> pressure, light, electricity before UPS, ...) which are known to work
> >> with openbsd ?
[...]
> Mo
On 11/4/06, Jon Simola <[EMAIL PROTECTED]> wrote:
On 10/4/06, Theo de Raadt <[EMAIL PROTECTED]> wrote:
> The Broadcom 802.11 chipsets are the bastards of the industry. They
> are the most complicated and difficult to program.
http://bcm-specs.sipsolutions.net, and it'
On 11/7/06, Price, Joe <[EMAIL PROTECTED]> wrote:
We're trying our first upgrade to 4.0 and fsck during the upgrade
process seems to freeze the machine.
wd0: 16-sector PIO, LBA48, 238475MB, 488397168 sectors
a: 47185884963 4.2BSD 2048 16384 328 # Cyl
0*-468113
real mem
On 10/4/06, Theo de Raadt <[EMAIL PROTECTED]> wrote:
The Broadcom 802.11 chipsets are the bastards of the industry. They
are the most complicated and difficult to program. Broadcom's
division is not interested in helping at all.
A Linux team has managed to mostly reverse engineer a subset of
On 11/1/06, Bryan <[EMAIL PROTECTED]> wrote:
Do adapters have chipsets in them as well? I mean, according to the
picture, it would appear pretty simple. Just move the contacts to the
correct connections on the PCI slot.
http://www.routerboard.com/rb11.html is $19 from a decent company in
Lat
On 10/30/06, stuartv <[EMAIL PROTECTED]> wrote:
Can anyone point me at some sample code for kevent. I am trying to
write a program that will watch a file for a write and can then
read the new lines and act upon them. So far, I get the first event
but not subsequent events.
tail(1) uses kevent
On 10/26/06, Jon Simola <[EMAIL PROTECTED]> wrote:
I've been playing with my USB mouse, trying to get it to work. I've
found one message in the archives (unanswered) asking about this exact
mouse, a Microsoft Comfort Optical Mouse 3000.
Just an update, if this attracts anyo
I've been playing with my USB mouse, trying to get it to work. I've
found one message in the archives (unanswered) asking about this exact
mouse, a Microsoft Comfort Optical Mouse 3000. I'd like to get this
working, and would appreciate any applications of a cluestick or other
ideas.
It is probed
On 10/25/06, Douglas Hunter <[EMAIL PROTECTED]> wrote:
Other than bsdtalk, NYCBUG and some rare one off taster programmes are there
any recordings of talks about OpenBSD (OGG or MP3) available on the web ?
I'm really hoping someone recorded Theo's talk at the CUUG last night.
I've seen the sli
On 10/20/06, Marc Balmer <[EMAIL PROTECTED]> wrote:
> Would I be correct in assuming the warning is probably due to a weak
> fix by the GPS device?
The sensor state is documented in nmea(4).
Okay, so it's just passing along the GPS's warning, not interpreting
results. Time to get a better GPS
On 10/19/06, Steve Williams <[EMAIL PROTECTED]> wrote:
I am 99% sure that I have seen on the internet SOMEWHERE a "whitelist"
of servers that are like this. I thought Bob Beck had forwarded one at
one point in time, but I can only find his post regarding the tarfile he
maintains for the "zombie
(Feeling rather stupid after the blank email, apologies)
I grabbed an older GPS from that Microsoft Streets and Trips software
and plugged it into my laptop to try the nmea sensor stuff. The
sticker says it's a GPS-360, mfg by Pharos USA with a SiRF chipset.
There looks to be a small bug in the
--
Jon
On 10/13/06, [EMAIL PROTECTED]
<[EMAIL PROTECTED]> wrote:
That is, I am running firmware version 813G. [According to the LSILogic
website, it was released on 2005.03.11, and is now 5 versions old.]
Okay, I'm trying this with an LSI 300-8X, 814B/H431 firmware, with an
AMD64 4.0 snapshot from e
On 10/13/06, S t i n g r a y <[EMAIL PROTECTED]> wrote:
altq on $extif hfsc bandwidth 640Kb queue {others www msn https smtp}
whats happening ? should it limit it to 188Kb fixed ? as i set the upperlimit.
I'm going to guess you're queueing on the wrong interface.
--
Jon
On 10/13/06, [EMAIL PROTECTED]
That is, I am running firmware version 813G. [According to the LSILogic
website, it was released on 2005.03.11, and is now 5 versions old.]
I've got a spare with 813G, and my production one is 813J, fixed a few
little issues.
Do you have a BBU on that card? Wit
On 10/12/06, S t i n g r a y <[EMAIL PROTECTED]> wrote:
i am facing problems using hfsc with PF.
That would be the first problem. Mention of HFSC was scrubbed from the
PF FAQ at http://www.openbsd.org/faq/pf/queueing.html for good reason.
Everything I learned about HFSC was from other web site
On 10/11/06, Sam Fourman Jr. <[EMAIL PROTECTED]> wrote:
For those of you that are knowledgeable, and have the time to respond
does anyone see any troubles with this hardware selection?
I am mostly concerned with the raid Controller selection I am
expecting it to have raid 5 across 16 drives with
might be able to extract raw data rows, running strings will
show you ascii text, tar and most files have a recognizable header
that you might be able to find. You'll be writing your own tools from
scratch and learning far more than you wanted to about filesystems and
file formats.
--
Jon Simola
You
may want to try forcing speed and duplex, that fixed one of my bge
problems.
--
Jon Simola
Systems Administrator
ABC Communications
ork Admin, still not available as
a package yet. If you can't find one (check behind the filing
cabinets), you'll want to investigate snmp, syslog, cron, rsync, your
favourite scripting language, and perhaps a nice monitoring solution
(I've used Cacti, Nagois, and Argus at var
olve others (notably hard lock when promoting drives to hot
spare). Company doesn't want to spring for a spare power supply so I
haven't been able to try replicating that on my spare hardware yet.
--
Jon Simola
Systems Administrator
ABC Communications
enclosures you linked to are dumb sleds. They do have
activity lights, so you could always perform some heavy drive activity
and, by a process of elimination, the one without the blinking
activity light is the failed drive.
--
Jon Simola
Systems Administrator
ABC Communications
set, but it's over 600 lines long.)
Mine is a similar size, mostly NAT and RDR rules for client<->DMZ traffic.
--
Jon Simola
Systems Administrator
ABC Communications
_advbase;
ch_tv.tv_usec = ch->carp_advskew * 100 / 256;
--
Jon Simola
Systems Administrator
ABC Communications
not reconnect the fan and see if that helps?
> I've got a feeling the little box will just give up or even worse
> blow up.
Melt down, most likely.
--
Jon Simola
Systems Administrator
ABC Communications
t via the printer port, but via lpd:
> http://patrick.wagstrom.net/old/weblog/archives/000128.html
Heh, I was trying to remember how to wire up the resistor ladder and
op-amp for nostalgia's sake.
--
Jon Simola
Systems Administrator
ABC Communications
y0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
sysbeep0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
lm0 at isa0 port 0x290/8: W83627HF
dkcsum: sd0 matches BIOS drive 0x80
root on sd0a
rootdev=0x400 rrootdev=0xd00 rawdev=0xd02
--
Jon Simola
Systems Administrator
ABC Communications
network
interfaces entering or leaving the host based on filter rules as de-
scribed in pf.conf(5).
There, thread over.
--
Jon Simola
Systems Administrator
ABC Communications
time=0.208 ms
--- 10.188.3.4 ping statistics ---
2 packets transmitted, 2 packets received, 0.0% packet loss
round-trip min/avg/max/std-dev = 0.208/0.231/0.255/0.027 ms
bash-3.00#
Works here, not intended for small children and the elderly, no
implied usability, etc...
--
Jon Simola
Systems Administrator
ABC Communications
0% and generally takes 5 to 6 hours
with the 300GB drives. RAID5 would probably be a faster rebuild (more
spindles to read from).
--
Jon Simola
Systems Administrator
ABC Communications
sed 300018565120 0:7.0 noencl
--
Jon Simola
Systems Administrator
ABC Communications
the legacy
> ISA system, which will then redirect based on hostname. I'm hesitant to
> use up all our IPs for option 1, but I'm thinking option 2 is even
> worse... Are there any options I haven't thought of?
Use squid in acceleration mode (reverse proxy)?
--
Jon Simola
Systems Administrator
ABC Communications
v 0x00
pchb6 at pci0 dev 25 function 2 "AMD AMD64 DRAM Cfg" rev 0x00
pchb7 at pci0 dev 25 function 3 "AMD AMD64 Misc Cfg" rev 0x00
isa0 at mainbus0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
sysbeep0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
lm0 at isa0 port 0x290/8: W83627HF
dkcsum: sd0 matches BIOS drive 0x80
root on sd0a
rootdev=0x400 rrootdev=0xd00 rawdev=0xd02
--
Jon Simola
Systems Administrator
ABC Communications
On 11/14/05, Steve B <[EMAIL PROTECTED]> wrote:
> problem I am faced with is how to implement MFS for a predefined user and
> their associated /home/username directory.
Maybe I'm missing something, but is there any reason MFS wouldn't work?
/sbin/mount_mfs -s 512000 swap
. Automagically locks
out agressive clients such as viruses and P2P users (and people
browsing Fark photoshop threads). For bonus points, script the
addition of the MAC address to your switching ACLs.
--
Jon Simola
Systems Administrator
ABC Communications
g. now
> things are running fine.
Wipe and recreate the partition/slice/disklabel from scratch. The
on-disk configuration doesn't match what the controller thinks it
should be.
--
Jon Simola
Systems Administrator
ABC Communications
ab at it in the
next week or two.
> If somebody can share appropriate fragments of their working
> /etc/hostname.* stuff, together with relevant hints for dhcpd, etc.,
> that would be real nice. Ta muchly.
My sentiments, exactly.
--
Jon Simola
Systems Administrator
ABC Communications
ame way with OpenBSD.
Unneccessarily complexities with little or no added security benefits.
--
Jon Simola
Systems Administrator
ABC Communications
61 matches
Mail list logo
