john wrote:
n Mon, Mar 27, 2006 at 03:28:57AM +0200, Sara Stymne wrote:
If I put the page break before or between the floats the
pages get right, but then the page with the last table gets the empty
heading, and the library page gets a normal heading. Or neither of
them
gets any headings if
On Mon, Mar 27, 2006 at 11:29:27AM +0200, Sara Stymne wrote:
> I have tried that, and putting it in the middle of the page to, but it
> is not working, because I get an extra blank page before the library
> page and empty gets applied to that, and the library page still gets
> headings. I get th
Hi,
I have following code in my document to center all images.
\makeatletter
\renewenvironment{figure}[1][]{%
[EMAIL PROTECTED]
\centering
}{%
[EMAIL PROTECTED]
}
\makeatother
I would like to extend this so that it automatically scales down an
image which is wider than 0.9\textwidth to 0.9\text
> "pol" == pol <[EMAIL PROTECTED]> writes:
pol> I need to write a two column doc, printing only the upper half
pol> side of A4 paper. Is there a way to easlily split the document?
pol> An alternative way would be defining a special paper format,
pol> corresponding to half A4. Any hints?
A5
un-suscribe
__
Do You Yahoo!?
Tired of spam? Yahoo! Mail has the best spam protection around
http://mail.yahoo.com
Hi,
I am writing up some code snippets where the output and some of the
snippets (and variable names) need to go inline in a fixed width font
(as opposed to a new paragraph styled with Lyx-code). I can find
commands to make text bold and emphasised, but not this. Is it possible?
This is Ly
Johan Blok wrote:
Hello,
I just created this command sequence in my bind file:
\bind"M-j d" "command-sequence footnote-insert; citation-insert;"
One I press the key sequence I get a footnote and the usual dialog to
select an item of the bibliography. Unfortunately, when I select one and
ch
Peter Bowyer wrote:
Hi,
I am writing up some code snippets where the output and some of the
snippets (and variable names) need to go inline in a fixed width font
(as opposed to a new paragraph styled with Lyx-code). I can find
commands to make text bold and emphasised, but not this. Is it p
Hi,
i am trying to put the subsection or section number and the names of
section/subsection in the header. i used the following commands in the
preamble
\usepackage{fancyhdr}
\pagestyle{fancy}
\renewcommand{\subsectionmark}[1]{\markright{\thesubsection.\ #1}}
\fancyhead[L]{\nouppercase \rig
Hello,
I am trying to compile lyx 1.3.7 on Debian/sarge but I am not having
much luck. I've attached the config.log file. Shown below is the
error message. It's probably that I either don't have the correct
packages installed or I don't have all the paths I need when I
'configure'. On the othe
I want to install a file named:
siimmac.cls
into my document classes. It commes with no other files.
You may find the file at:
http://www.emate.ucr.ac.cr/simmac/simmac.cls
Pierre
You can verify that you have all the packages needed for build by
looking here:
http://packages.debian.org/stable/source/lyx
It lists the "build-depends" for the official stable LyX package, i.e.
those packages that must be installed for the package to be built.
That will be a superset of the
On Wed, Mar 22, 2006 at 01:42:10PM +0900, Ride_Ride_Ride wrote:
> I'm sorry that my question(s) is not associated with Lyx itself, but I
> have another question about this Lyx ML.
>
> Why this ML doesn't use "Reply-to"?
Because this is generally a bad idea. Therer are pointers in the
archives ex
13 matches
Mail list logo
