Re: Stus-List Water Storage on 35-II & Drill Bit Set question

Lee, You should not be gathering water in that area. Since you are the limber holes (a drain hole through a boat frame, designed to prevent water from accumulating against one side of the frame, and allowing it to drain toward the bilge (Wikipedia)) is blocked. You should have a series of lim

Re: Stus-List Water Storage on 35-II & Drill Bit Set question

My friend's 35 Mk.1 has a panel that can be removed at the foot of the Quarter Berth that provides some access to this area for a smaller person. Does the Mk.2 have one? You might want to make an access there? Ken H. On Wed, 28 Nov 2018 at 10:29, Don Kern via CnC-List wrote: > Lee, > > You sho

Re: Stus-List Water Storage on 35-II & Drill Bit Set question

The drill bit set is from Norseman. You can get them off Amazon. On Tue, Nov 27, 2018, 10:25 PM Lee Youngblood via CnC-List < cnc-list@cnc-list.com wrote: > Hi All, > > I have a sweet C&C 35-II, and I’m storing a few gallons of water in the > stern of the boat, on both sides of the vertical bulkh

Stus-List Limber hole issue

Listers: While on the topic of unwanted water accumulation, I have a couple limber holes that were not drilled level with the hull (about 1/2” too high) and, as a result, a certain amount water must accumulate before the area drains. The result is that these areas are always wet. I suppose

Stus-List Prop Shaft Strut - Removal, Alignment, and Re-bedding - C&C 36-1 KCB

Prop shaft strut is weeping around the nuts inside the hull and externally the fairing shows cracks around the perimeter of the strut base although it doesn't feel loose. No slop in the Cutlass bearing. She's on the hard for bottom job and driveline maintenance. I'm interested in your thoughts on h

Re: Stus-List Prop Shaft Strut - Removal, Alignment, and Re-bedding - C&C 36-1 KCB

Tim: The strut on my boat (42 Custom) was not mounted as securely as one would expect (no backing plate, for instance), and a prior owner had done an inadequate job on a previous repair. Probably the same PO that used bondo to level the limber holes – but I digress. Worse yet, the damaged

Re: Stus-List Water Storage on 35-II & Drill Bit Set question

Eric, would it possible to get a link to a photo of your panel installation? Thanks Richard s/v Bushmark4; 1085 C&C 37; Ohio River, Mile 596; Richard N. Bush 2950 Breckenridge Lane, Suite Nine Louisville, Kentucky 40220-1462 502-584-7255 -Original Message- From: Eric Frank via C

Re: Stus-List Limber hole issue

Matt, Some epoxy would do the trick. Might need some thickener. Joel Virus-free. www.avg.com

Stus-List Glue residue

Hey all; I finally managed to remove the 2018 CRW bow stickers from my boat--talk about delaying things! Anyhow, I am now left with the residue of the glue on my Awlgrip painted hull. Goo-gone did nothing to help remove them or the glue residue. I am thinking I need a petroleum based p

Re: Stus-List Glue residue

Lacquer thinner will not harm the paint, but it may not remove the glue. I would not use a scotch brite! Joel Virus-free. www.avg.com

Re: Stus-List Water Storage on 35-II & Drill Bit Set question

Hi Eric and Lee, I would also like to see what Eric has done. I was thinking of doing something like this to my MkII. It would certainly make access to the rear area a lot easier. As far as water getting into the rear quarter it might be getting in via the little wood/plastic panel that sits ju

Re: Stus-List Glue residue

Stripe off 3m wheel should work. I used it to get the old port of call off the transom of Persistence which has a painted hull. No scratches. Mike Persistence Halifax From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Charlie Nelson via CnC-List Sent: Wednesday, November 28, 2

Re: Stus-List Prop Shaft Strut - Removal, Alignment, and Re-bedding - C&C 36-1 KCB

Tim, While I haven't had to change out the strut, I've removed/reinstalled the engine a few times (don't ask), and used your basic approach:  shaft sliding easily in the bearing and centered in the log, then set the engine flange to the shaft flange while on the hard.  Checked it after splash

Stus-List Glue residue

I took the glue residue off my transom when I took the old name off with a very inexpensive product called Goo Gonea liquid in a small plastic container.after several applications, it even seemed to lift, at the least, lighten the gelcoat where the old vinyl was removed.  There is no ab

Re: Stus-List Glue residue

Hi Charlie - you are right to be hesitant about any type of cleaning pad (scotch-brite, etc). They will scratch your paint! Mike Atacama 33mkii Toronto On Wed, Nov 28, 2018, 2:12 PM Charlie Nelson via CnC-List < cnc-list@cnc-list.com wrote: > > Hey all; > > I finally managed to remove the 2018

Re: Stus-List Water Storage on 35-II & Drill Bit Set question

Several folks on the list seem to be interested in seeing the access panel I installed in the rear of Cat’s Paw's cockpit. I’ll be at the boat Sunday or Monday and will take pictures of the installation, so I can post them in the Public folder of my Dropbox. I’ll post the URL of that folder wh

Stus-List Prop shaft strut ....

Tim, I would recommend you check the shaft for true while you have it out, roll it on a flat surface like a granite countertop if you don’t have access to a shop. You need to eliminate all vibration. I would look at changing the prop if it doesn’t come back vibration free and do the final engine

Re: Stus-List Prop Shaft Strut - Removal, Alignment, and Re-bedding - C&C 36-1 KCB

Couple years ago, I removed Touche's strut to straighten it. It was a straightforward job. I did have to remove the fuel tank for access to the nuts. Upon re-install, I used a cone shaped grinding stone to chamfer the 4 fastener holes on the underside. This lets the sealant form an o-ring aroun

Re: Stus-List Glue residue

Most decal adhesives can be removed with mineral spirits. Dennis C. On Wed, Nov 28, 2018, 1:12 PM Charlie Nelson via CnC-List < cnc-list@cnc-list.com wrote: > > Hey all; > > I finally managed to remove the 2018 CRW bow stickers from my boat--talk > about delaying things! > > Anyhow, I am now lef

Re: Stus-List Glue residue

Rubbing alcohol is very effective in many cases too. From: CnC-List on behalf of Dennis C. via CnC-List Sent: November 28, 2018 4:54 PM To: CnClist Cc: Dennis C. Subject: Re: Stus-List Glue residue Most decal adhesives can be removed with mineral spirits. Denn