_
From: CnC-List [cnc-list-boun...@cnc-list.com] on behalf of Patrick Davin via
CnC-List [cnc-list@cnc-list.com]
Sent: Tuesday, August 11, 2015 8:29 PM
To: cnc-list@cnc-list.com
Cc: Patrick Davin
Subject: Stus-List Yanmar engine mounts replacement
Anyone have tips for replacing engine mounts on a
Mine were bolts not lag screws. I've never seen lag screws used. Mine are
either tapped right into the fiberglass or there is a nut or backing plate
embedded into the stringer. I looked at generic torque spec charts for the
size bolt I had and torqued them approximately once everything was align
[Oops, sorry about the Digest subject line, forgot to rename it before
sending my prior mail]
Where would you slide the angle iron? Under the rear mounts? The forward
mounts are the ones visible in the picture in the link I sent (in the
drivetrain photo) -
https://drive.google.com/drive/folders/0B
>
> Steve Thomas
> C&C27 MKIII
> Port Stanley, ON
>
> - Original Message -
> *From:* Robert Boyer via CnC-List
> *To:* cnc-list@cnc-list.com
> *Cc:* Robert Boyer ; Patrick Davin
>
> *Sent:* Wednesday, August 12, 2015 06:00
> *Subject:* Re: Stus-L
PITA...
Cheers,Aaron R.Admiral Maggie,1979 C&C 30 MK1 #540Annapolis, MD
Date: Tue, 11 Aug 2015 20:29:29 -0700
To: cnc-list@cnc-list.com
Subject: Stus-List Yanmar engine mounts replacement
From: cnc-list@cnc-list.com
CC: jda...@gmail.com
Anyone have tips for replacing engine mounts on a Yanmar 3HM?
cnc-list.com>"
> mailto:cnc-list@cnc-list.com>>
> Subject: Stus-List Yanmar engine mounts replacement
> Message-ID:
><mailto:CAHixY6QzJHe=xqzqbdolqjpqnwidhyq2e7qtvsjybt66um+...@mail.gmail.com>>
> Content-Type: text/plain; charset="utf-8"
>
; Steve Thomas
> C&C27 MKIII
> Port Stanley, ON
>
> - Original Message -
> *From:* Robert Boyer via CnC-List
> *To:* cnc-list@cnc-list.com
> *Cc:* Robert Boyer ; Patrick Davin
>
> *Sent:* Wednesday, August 12, 2015 06:00
> *Subject:* Re: Stus-List Yanmar en
, ON
- Original Message -
From: Robert Boyer via CnC-List
To: cnc-list@cnc-list.com
Cc: Robert Boyer ; Patrick Davin
Sent: Wednesday, August 12, 2015 06:00
Subject: Re: Stus-List Yanmar engine mounts replacement
Patrick:
The yard replaced all four of my mounts when my
I replaced all 4 of mine 2 winters ago with PYI. They are captured so even
if/when the rubber breaks down or delaminates the mount will still hold the
engine. Yanmar even recognizes the possibility of a torn engine mount and
recommends installing a heavy gauge "twist tie" to prevent the engine fr
Patrick:
The yard replaced all four of my mounts when my fuel tank was replaced over a
winter. If I recall correctly, they replaced one at a time and didn't need a
jack. The two aft mounts were the toughest.
Bob
Sent from my iPhone, Bob Boyer
> On Aug 11, 2015, at 11:29 PM, Patrick Davin vi
Hi PatrickNot sure a sissor jack will fit. You might have to get creative
in supporting the nack of the engine. For realignment purposes, I would
recommend measuring the existing height of the mounts. That will get you close
for realigning the shaft. I think the hull will support half
Anyone have tips for replacing engine mounts on a Yanmar 3HM? In terms of
the logistics, like how to prop up the engine, get the old mounts out, etc.
I have the transmission out now for a rebuild (fwd clutch failed) so it's
the perfect time to replace mounts. I'm just going to do the forward two
(
12 matches
Mail list logo
