been
flushed and it is a long ways from new. So will everything come out in
small pieces or will there be big hose plugging flakes?
Any help?
Thanks
Don
From: dre...@gmail.com [mailto:dre...@gmail.com]
Sent: May-24-13 7:41 AM
To: cnc-list@cnc-list.com
Subject: Re: Stus-List Overh
se with a rag or your hand.
>>> If the flow and pressure are good, move downstream. If no flow or you can
>>> stop the flow then the issue is the pump or ahead of the pump.
>>>
>>> If the flow is good, disconnect the hose to the little elbow you cleaned.
>
That is a really interesting tip to store away, and (Hopefully) remember!
Bill Coleman
C&C 39 animated_favicon1
From: CnC-List [mailto:cnc-list-boun...@cnc-list.com] On Behalf Of Gary
Nylander
Sent: Friday, May 24, 2013 11:21 AM
To: cnc-list@cnc-list.com
Subject: Re: Stus-List Overhea
; 35-1 #83
Mandeville, LA
--
From: Knowles Rich
To: "cnc-list@cnc-list.com"
Sent: Thursday, May 23, 2013 8:35 PM
Subject: Re: Stus-List Overheating 3GMD - the plot thickens
Suggest checking the raw water pump impellor to make sure the bronze
insert is not sp
Hi,
My raw water cooled 2QM15 had a problem of intermitting over heating. I check
and replaced many things: hoses, belts, impeller, ... I even pickled the
engine with vinegar and turned over water pump impeller backing plate thinking
the wear was limiting flow. I even thought I licked the
My raw water cooled Yanmar 2qm15 would start with a normal flow of water.
On restarting after a sail, no water flow. This repeated regularly until
the thermostat was changed.
Ed
C&C 30 Mk 1 Dream Girl (for sale)
C&C 34 Briar Patch
New Orleans___
Thi
As others have mentioned, I'd look for an air leak in every seal from
the pump upstream to the hull fitting -including the entire pump.
If the pump gets air bound and the impeller vanes are less than
absolutely factory perfect, it will have a hard time sucking water, and
will just move the air in t
.
Touche' 35-1 #83
Mandeville, LA
--
*From:* Knowles Rich
*To:* "cnc-list@cnc-list.com"
*Sent:* Thursday, May 23, 2013 8:35 PM
*Subject:* Re: Stus-List Overheating 3GMD - the plot thickens
Suggest checking the raw water pump impellor to make sure
ssure there.
Dennis C.
Touche' 35-1 #83
Mandeville, LA
>
> From: Knowles Rich
>To: "cnc-list@cnc-list.com"
>Sent: Thursday, May 23, 2013 8:35 PM
>Subject: Re: Stus-List Overheating 3GMD - the plot thickens
>
>
>
>
Suggest checking the raw water pump impellor to make sure the bronze insert is
not spinning inside the rubber impellor. This can happen with a new or old unit
and can fool you in an inspection as the rubber vanes may look perfect.
Rich Knowles
Indigo. LF38
Halifax
On 2013-05-23, at 22:00, "Don
I assume you checked your seacock and strainer for blockage? I usually
start troubleshooting at the easy stuff, like is there a fish in my water
intake?
The answer is yes, twice. The second time it happened, it was the first
thing I checked. The first time it happened, it was about the 84th.
On 2
Hey Don, I had similar issues with my raw water SB8 on a Mirage 26 and it ended
up being the cooling passages in the head and block. I tore it down and cleaned
them out. Was a long process but manageable. Not sure how complicated it would
be on a 3 gm. Very satisfying when I was done and sat bac
12 matches
Mail list logo
